MKMinkyun Kang

Minkyun Kang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Minkyun Kang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Plasma Excitation Mode on Rutile TiO2 MIM Capacitors Grown on RuO2 Seed Electrodes

    by Yongwoon Jang, Byungwook Kim, Hyeonwu Nam, Minkyun Kang, Changyun Hong, Changbun Yoon

    Maintaining low leakage current with high capacitance density in metal–insulator–metal (MIM) capacitors is essential for next-generation dynamic random-access memory (DRAM) scaling. Rutile TiO2 is a promising high-k dielectric; however, its narrow bandgap causes high leakage, while defect-free stabilization in ultrathin films remains challenging. RuO2/TiO2/Ru MIM capacitors were fabricated using a reactive direct current (DC)-sputtered RuO2 bottom electrode, followed by TiO2 growth by direct plasma atomic layer deposition (DP-ALD) or remote plasma atomic layer deposition (RP-ALD) and rapid thermal annealing in O2 to reduce defects. Rutile TiO2 was deposited directly on highly crystalline RuO2 under both plasma modes, suggesting that RuO2 crystallinity governs TiO2 phase evolution. The RP-ALD film replicated the RuO2 grain morphology, yielding higher roughness than that of the DP-ALD film. Moreover, the RP-ALD film exhibited lower oxygen-vacancy density and improved stoichiometric stability. The RP-ALD-fabricated capacitors exhibited a higher dielectric constant and lower leakage current density at 0.8 V than the DP-ALD-fabricated capacitors (~100 and ~1.76 × 10−6 A/cm2 vs. ~97 and ~1.41 × 10−4 A/cm2, respectively). Ion bombardment during DP-ALD likely promoted oxygen-vacancy-related defect formation, whereas RP-ALD mitigated such damage, improving leakage characteristics. This work highlights the potential of RP-ALD-based RuO2/TiO2/Ru MIM capacitors for next-generation DRAM.

  • Open Access

    Selective Plasma Mode Modulation in HfO2 Charge Trap Layers via RP/DP/RP Atomic Layer Deposition for Enhanced Memory Performance and Interface Quality

    by Byungwook Kim, Yongwoon Jang, Hyeonwu Nam, Changyun Hong, Minkyun Kang, Wookyung Lee, Changbun Yoon

    Hafnium oxide (HfO2) has emerged as a promising charge trap layer (CTL) for nonvolatile memory devices; however, its long-term reliability remains challenging due to leakage current through grain boundary pathways and interface defect formation. Within plasma-enhanced atomic layer deposition (PEALD), direct plasma ALD (DPALD) forms crystalline HfO2 with deeper trap sites, while its ion-assisted nature may contribute to interface damage, resulting in a lower net trap density than remote plasma ALD (RPALD), which better preserves interfacial quality. We propose an interface–bulk–interface (RP/DP/RP) process design that places RPALD at the interfaces and DPALD in the bulk, aiming to combine bulk trap sites with interfacial protection. Charge trap memory (CTM) devices were fabricated across RP/DP/RP thickness combinations. Within the tested range, the optimized structure exhibited the widest memory window and the highest effective trapped charge density among the measured devices, improving upon DPALD and comparable to RPALD, together with the lowest near-interface trap density at the Si/Al2O3 interface. The device also maintained a stable memory window up to 104 program/erase cycles, and short-term retention data suggest potentially stable program and erase states, requiring longer-term validation. These results indicate that spatial modulation of plasma modes offers a process-level strategy for improving HfO2-based CTM devices.

  • Open Access

    Interface-Engineered, Low-Damage IGZO/HfO2 Charge-Trapping Memory Devices Fabricated Using a Remote Plasma ALD Process

    by Inkook Hwang, Hyeonwu Nam, Jiwon Kim, Byungwook Kim, Yongwoon Jang, Wookyung Lee, Minkyun Kang, Changbun Yoon

    In this study, charge-trapping memory (CTM) transistors were developed using indium gallium zinc oxide (IGZO) as the oxide semiconductor channel and high-k HfO2 as the charge-trapping layer, aiming for next-generation nonvolatile memory applications. To evaluate the impact of plasma exposure on film quality and device performance, HfO2 thin films were deposited via atomic layer deposition (ALD) using both direct plasma (DP) and remote plasma (RP) modes. Post-deposition annealing (PDA) was applied to the IGZO and HfO2 layers, with experiments conducted at various annealing temperatures to enhance the interfacial stability between the HfO2 layer and the IGZO channel. Electrical characterization results demonstrated that the RP-processed devices exhibited a wider memory window, reduced gate leakage current, and improved threshold voltage stability compared with the DP-processed devices. Thermal treatment effectively reduced the interfacial defect density and enhanced the crystallinity at the dielectric–channel interface. These findings underscore that the selection of the plasma process and annealing conditions is critical in determining the electrical characteristics and reliability of oxide semiconductor-based CTM devices.