Chau-Tan-Phat Le
Research Subjects
Chau-Tan-Phat Le has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Xuan-Huy Nguyen
Department of Electrical Engineering, National Kaohsiung University of Science and Technology, Kaohsiung 80778, Taiwan
3 shared publications - Thanh-Tuan Nguyen
Faculty of Electrical and Electronics Engineering, Nha Trang University, Nha Trang, 650000, Vietnam
2 shared publications Thanh-Tuan Nguyen
1 shared publication
Latest Publications
- 15 September 2026
- Published by Elsevier in Materials Today Nano
- Vol. 36
Composition-dependent deformation pathways and non-monotonic strength-toughness synergy in CuxCoCrFeNi high-entropy alloy nanowires
- 15 September 2026
- Published by Elsevier in Materials Today Nano
- Vol. 36
Composition-dependent deformation pathways and non-monotonic strength-toughness synergy in CuxCoCrFeNi high-entropy alloy nanowires
- Open Access
- 21 July 2026
- Published by Elsevier in SSRN Electronic Journal
Composition-dependent deformation pathways and non-monotonic strength-toughness synergy in CuxCoCrFeNi high-entropy alloy nanowires
We report statistically replicated molecular dynamics simulations of CuxCoCrFeNi (x = 0.5, 1.0, 1.5) nanowires under uniaxial tension at 100, 300, 600 and 900 K, using the Farkas-Caro embedded-atom method potential with n = 3-4 independent configurations per condition (CVUTS < 2.1% in all 12 cases). Seven mechanical parameters extracted from each stress-strain curve are read against Von Mises shear strain maps taken at three stages of deformation. The equiatomic composition exhibits a non-monotonic strength-toughness optimum. Cu1.0CoCrFeNi at 100 K records both the highest ultimate tensile strength (22.84 ± 0.37 GPa) and the highest toughness modulus (2.06 ± 0.09 GPa) of any condition studied, exceeding Cu0.5 in toughness by deltaUt = 0.20 GPa at essentially the same peak stress. The strain maps at 300 K identify three distinct failure routes: diffuse multi-zone slip in Cu0.5, a single shear band that forms abruptly in Cu1.0, and early planar fracture seeded by void nucleation in Cu1.5. The timing of plastic localisation differs across compositions. Cu1.0 remains in the low-strain regime at both the sub-UTS and near-UTS frames, whereas Cu0.5 already carries slip traces and Cu1.5 shows strain concentrating at two sites. This constitutes direct atomistic evidence for a delayed-localisation mechanism. Independently of composition, the 0.2% offset yield strength falls from roughly 7.5-8.5 GPa at 100 K to 2.2-2.6 GPa at 900 K while the hardening capacity (σUTS -σy)/σUTS rises from about 62% to about 85%, a shift attributed to thermally activated, surface-dominated dislocation nucleation. These results map the deformation pathways of CuxCoCrFeNi nanowires and provide quantitative guidance for designing nanostructured HEAs.
- 21 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessComposition-dependent deformation pathways and non-monotonic strength-toughness synergy in CuxCoCrFeNi high-entropy alloy nanowires
We report statistically replicated molecular dynamics simulations of CuxCoCrFeNi (x = 0.5, 1.0, 1.5) nanowires under uniaxial tension at 100, 300, 600 and 900 K, using the Farkas-Caro embedded-atom method potential with n = 3-4 independent configurations per condition (CVUTS < 2.1% in all 12 cases). Seven mechanical parameters extracted from each stress-strain curve are read against Von Mises shear strain maps taken at three stages of deformation. The equiatomic composition exhibits a non-monotonic strength-toughness optimum. Cu1.0CoCrFeNi at 100 K records both the highest ultimate tensile strength (22.84 ± 0.37 GPa) and the highest toughness modulus (2.06 ± 0.09 GPa) of any condition studied, exceeding Cu0.5 in toughness by deltaUt = 0.20 GPa at essentially the same peak stress. The strain maps at 300 K identify three distinct failure routes: diffuse multi-zone slip in Cu0.5, a single shear band that forms abruptly in Cu1.0, and early planar fracture seeded by void nucleation in Cu1.5. The timing of plastic localisation differs across compositions. Cu1.0 remains in the low-strain regime at both the sub-UTS and near-UTS frames, whereas Cu0.5 already carries slip traces and Cu1.5 shows strain concentrating at two sites. This constitutes direct atomistic evidence for a delayed-localisation mechanism. Independently of composition, the 0.2% offset yield strength falls from roughly 7.5-8.5 GPa at 100 K to 2.2-2.6 GPa at 900 K while the hardening capacity (σUTS -σy)/σUTS rises from about 62% to about 85%, a shift attributed to thermally activated, surface-dominated dislocation nucleation. These results map the deformation pathways of CuxCoCrFeNi nanowires and provide quantitative guidance for designing nanostructured HEAs.
- Open Access
- 24 June 2026
- Published by Elsevier in SSRN Electronic Journal
Composition-dependent deformation pathways and non-monotonic strength-toughness synergy in CuxCoCrFeNi high-entropy alloy nanowires
We report statistically replicated molecular dynamics simulations of CuxCoCrFeNi (x = 0.5, 1.0, 1.5) nanowires under uniaxial tension at 100, 300, 600 and 900 K, using the Farkas-Caro embedded-atom method potential with n = 3-4 independent configurations per condition (CVUTS < 2.1% in all 12 cases). Seven mechanical parameters extracted from each stress-strain curve are read against Von Mises shear strain maps taken at three stages of deformation. The equiatomic composition exhibits a non-monotonic strength-toughness optimum. Cu1.0CoCrFeNi at 100 K records both the highest ultimate tensile strength (22.84 ± 0.37 GPa) and the highest toughness modulus (2.06 ± 0.09 GPa) of any condition studied, exceeding Cu0.5 in toughness by deltaUt = 0.20 GPa at essentially the same peak stress. The strain maps at 300 K identify three distinct failure routes: diffuse multi-zone slip in Cu0.5, a single shear band that forms abruptly in Cu1.0, and early planar fracture seeded by void nucleation in Cu1.5. The timing of plastic localisation differs across compositions. Cu1.0 remains in the low-strain regime at both the sub-UTS and near-UTS frames, whereas Cu0.5 already carries slip traces and Cu1.5 shows strain concentrating at two sites. This constitutes direct atomistic evidence for a delayed-localisation mechanism. Independently of composition, the 0.2% offset yield strength falls from roughly 7.5-8.5 GPa at 100 K to 2.2-2.6 GPa at 900 K while the hardening capacity (σUTS -σy)/σUTS rises from about 62% to about 85%, a shift attributed to thermally activated, surface-dominated dislocation nucleation. These results map the deformation pathways of CuxCoCrFeNi nanowires and provide quantitative guidance for designing nanostructured HEAs.
- 24 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessComposition-dependent deformation pathways and non-monotonic strength-toughness synergy in CuxCoCrFeNi high-entropy alloy nanowires
We report statistically replicated molecular dynamics simulations of CuxCoCrFeNi (x = 0.5, 1.0, 1.5) nanowires under uniaxial tension at 100, 300, 600 and 900 K, using the Farkas-Caro embedded-atom method potential with n = 3-4 independent configurations per condition (CVUTS < 2.1% in all 12 cases). Seven mechanical parameters extracted from each stress-strain curve are read against Von Mises shear strain maps taken at three stages of deformation. The equiatomic composition exhibits a non-monotonic strength-toughness optimum. Cu1.0CoCrFeNi at 100 K records both the highest ultimate tensile strength (22.84 ± 0.37 GPa) and the highest toughness modulus (2.06 ± 0.09 GPa) of any condition studied, exceeding Cu0.5 in toughness by deltaUt = 0.20 GPa at essentially the same peak stress. The strain maps at 300 K identify three distinct failure routes: diffuse multi-zone slip in Cu0.5, a single shear band that forms abruptly in Cu1.0, and early planar fracture seeded by void nucleation in Cu1.5. The timing of plastic localisation differs across compositions. Cu1.0 remains in the low-strain regime at both the sub-UTS and near-UTS frames, whereas Cu0.5 already carries slip traces and Cu1.5 shows strain concentrating at two sites. This constitutes direct atomistic evidence for a delayed-localisation mechanism. Independently of composition, the 0.2% offset yield strength falls from roughly 7.5-8.5 GPa at 100 K to 2.2-2.6 GPa at 900 K while the hardening capacity (σUTS -σy)/σUTS rises from about 62% to about 85%, a shift attributed to thermally activated, surface-dominated dislocation nucleation. These results map the deformation pathways of CuxCoCrFeNi nanowires and provide quantitative guidance for designing nanostructured HEAs.