Karahan Ocak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Karahan Ocak has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Aisha Gokce Ozbay
TUBITAK UME (National Metrology Institute), Kocaeli 41470, Türkiye
1 shared publication - Aykut Can Önel
TUBITAK UME (National Metrology Institute), Kocaeli 41470, Türkiye
1 shared publication - Kaan Orhan
Department of Oral and Maxillofacial Radiology, Faculty of Dentistry, Ankara University, Ankara 06560, Türkiye
1 shared publication - Kagan Berk
Department of Orthodontics, University Hospital Schleswig Holstein, Arnold-Heller-Straße 3, 24105 Kiel, Germany
1 shared publication - Oral Cenk Aktas
Department of Orthodontics, University Hospital Schleswig Holstein, Arnold-Heller-Straße 3, 24105 Kiel, Germany
1 shared publication - Salih Veziroglu
Chair for Multicomponent Materials, Department of Materials Science, Faculty of Engineering, Kiel University, Kaiserstr. 2, 24143 Kiel, Germany
1 shared publication
Latest Publications
- Open Access
- 30 June 2026
- Published by MDPI AG in Journal of Functional Biomaterials
- Vol. 17 (7) , 315
Influence of Post-Processing Techniques on Surface Roughness, Wettability, and Friction of SLM-Manufactured CoCrW Orthodontic Materials
This study investigates the effects of post-processing on the surface roughness, wettability, and frictional behavior of selective laser-melted (SLM) cobalt–chromium–tungsten (CoCrW) alloys for orthodontic use. The SLM-CoCrW specimens were tested in as-manufactured, mechanically polished, and electropolished states. Surface characterization via stylus profilometry and atomic force microscopy (AFM) showed that both polishing methods reduced macro- and micro-scale roughness, with electropolishing producing the smoothest, most uniform topography. Static water contact angle (WCA) measurements revealed that mechanical polishing provided an optimal balance of roughness and hydrophilicity, resulting in the lowest friction, while ultrasmooth electropolished surfaces exhibited slightly higher friction due to increased hydrophobicity and a uniform Cr-rich oxide layer confirmed by X-ray photoelectron spectroscopy (XPS). XPS also indicated that electropolishing generated a homogenous chromium oxide passive film, whereas mechanical polishing left a chemically heterogeneous surface with exposed metallic sites. Importantly, performance is not governed solely by surface roughness; surface chemistry is equally critical, and both must be considered together—along with wettability and tribological behavior—to achieve optimal functional outcomes. From a clinical perspective, optimization of surface roughness and surface chemistry may result in decreased frictional resistance, improved sliding mechanics, and enhanced long-term performance of additively manufactured orthodontic components; however, the present study was restricted to in vitro characterization under simplified laboratory conditions, and further investigations involving artificial saliva, long-term aging, wear and clinical simulations are necessary to validate the translational relevance of these findings.
- 30 June 2026
- Published by MDPI AG in Journal of Functional Biomaterials
- Vol. 17 (7) , 315
Open AccessInfluence of Post-Processing Techniques on Surface Roughness, Wettability, and Friction of SLM-Manufactured CoCrW Orthodontic Materials
This study investigates the effects of post-processing on the surface roughness, wettability, and frictional behavior of selective laser-melted (SLM) cobalt–chromium–tungsten (CoCrW) alloys for orthodontic use. The SLM-CoCrW specimens were tested in as-manufactured, mechanically polished, and electropolished states. Surface characterization via stylus profilometry and atomic force microscopy (AFM) showed that both polishing methods reduced macro- and micro-scale roughness, with electropolishing producing the smoothest, most uniform topography. Static water contact angle (WCA) measurements revealed that mechanical polishing provided an optimal balance of roughness and hydrophilicity, resulting in the lowest friction, while ultrasmooth electropolished surfaces exhibited slightly higher friction due to increased hydrophobicity and a uniform Cr-rich oxide layer confirmed by X-ray photoelectron spectroscopy (XPS). XPS also indicated that electropolishing generated a homogenous chromium oxide passive film, whereas mechanical polishing left a chemically heterogeneous surface with exposed metallic sites. Importantly, performance is not governed solely by surface roughness; surface chemistry is equally critical, and both must be considered together—along with wettability and tribological behavior—to achieve optimal functional outcomes. From a clinical perspective, optimization of surface roughness and surface chemistry may result in decreased frictional resistance, improved sliding mechanics, and enhanced long-term performance of additively manufactured orthodontic components; however, the present study was restricted to in vitro characterization under simplified laboratory conditions, and further investigations involving artificial saliva, long-term aging, wear and clinical simulations are necessary to validate the translational relevance of these findings.