Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jianwu Zhou has a total of 11 co-authors. Here are the top co-authors by number of shared publications:

  • Chengzhou Wang

    Northwestern Polytechnical University, Xi’an, China

    1 shared publication
  • Debin Song

    School of Aeronautics Northwestern Polytechnical University Xi'an Shaanxi China

    1 shared publication
  • Guangjie Kou

    School of Missile Engineering Rocket Force University of Engineering Xi'an Shaanxi China

    1 shared publication
  • Hui Cai

    School of Missile Engineering Rocket Force University of Engineering Xi'an Shaanxi China

    1 shared publication
  • Jingye Zhang

    School of Missile Engineering Rocket Force University of Engineering Xi'an Shaanxi China

    1 shared publication
  • Renjie Lu

    Northwestern Polytechnical University, Xi’an, China

    1 shared publication

Latest Publications

  • Failure Mechanism and Damage Tolerance Correlation Analysis of Carbon Fiber Reinforced Composites Under Compression After Impact Based on Multi‐Source Monitoring

    by Hui Cai, Zhibin Zhao, Debin Song, Jianwu Zhou, Guangjie Kou, Yu Li, Jingye Zhang, Zhengwei Yang

    A multi‐source monitoring approach integrating acoustic emission (AE), infrared thermography (IRT), and digital image correlation (DIC) was employed to investigate the compression‐after‐impact (CAI) failure mechanisms and damage tolerance of T800 carbon fiber reinforced polymer (CFRP) composites. CAI failure modes at representative impact energies were identified through load–displacement responses, out‐of‐plane displacement fields, and fracture morphologies. Damage modes were classified using principal component analysis combined with a Gaussian mixture model based on AE time‐frequency parameters. Thermodynamic responses during failure were characterized by IRT, while full‐field strain evolution and out‐of‐plane displacement distributions under different impact energies were analyzed using DIC. Pearson correlation analysis was further conducted to evaluate the relationships between key monitoring parameters and CAI damage tolerance. The results show that the displacement at peak load exhibits a non‐monotonic trend with increasing impact energy, reflecting alternating stiffness‐ and strength‐dominated behaviors. AE results reveal progressive damage evolution from matrix cracking to delamination and fiber fracture. At high impact energies, dual‐zone thermal hotspots correspond well with partitioned out‐of‐plane displacement fields, confirming localized buckling instability. Strong correlations are observed between CAI damage tolerance and AE energy, maximum average temperature rise, and axial strain. This study, validated through laboratory CAI tests, establishes an AE‐IRT‐DIC multi‐source synergistic monitoring and feature‐parameter screening methodology. It not only provides multi‐physics experimental evidence for a deeper understanding of CAI failure in composites, but also targets future in‐service structural health monitoring by informing the selection of key features required for post‐impact risk assessment.

  • Study of Surface Quality and Cutting Parameter Optimization in Side Milling CFRP With Diamond Coated Carbide Tool

    by Weiwei Liu, Yuan Hu, Jianwu Zhou, Renjie Lu, Chengzhou Wang

    Composite machining is one of the hot researches currently, and optimal cutting parameters are particularly important to get ideal surface and reduce processing cost of workpiece. By comparison, the present paper selects the surface root mean square deviation Sq as the three-dimensional evaluation parameter of surface roughness to reflect the special appearance after cutting accurately. The single-factor experiment and orthogonal experiment were conducted to study the machining defects emerged and effect of parameters on surface roughness when side milling CFRP (Carbon Fiber Reinforced Plastics) with diamond coated carbide tool. The mapping relationship between cutting parameters and surface roughness was established based on the experiment results. Then, the cutting parameters were optimized by using genetic algorithm with two conflicting objectives: material removal rate and surface roughness. The experiment results show that the proposed method is feasible and effective, and can provide references for the actual processing of CFRP.