Nikolay Ovcharenko has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Industrial Implementation and Performance of PEEK‐Based Plain Bearings in 17 Industrial Units Over a 7‐Year Period

    by Nikolay Ovcharenko

    The transition from Babbitt alloys to high‐performance polymer composite materials (PCMs) in hydrodynamic plain bearings represents a timely development for modern heavy machinery manufacturing. However, a substantial gap persists in scientific literature between laboratory/bench‐scale tribological research and the industrial adoption of polymer plain bearings (PPBs). This article presents an extensive field investigation, based on over 7 years of observational experience and the successful implementation of polyetheretherketone (PEEK)/carbon fiber (CF)30 bearings in more than 2000 industrial units across power generation, hydrocarbon transportation, metallurgy, and the chemical industry, and detailed physical data analysis of 17 pilot and flagship rotating machinery units (including gas, steam, and hydro turbines, compressors, and pumps). The obtained results demonstrate the advantages of PEEK‐based bearings: a multifold reduction in wear rate, a sustained increase in overall equipment efficiency, and high fault tolerance during oil starvation and emergency coast‐downs. The physical mechanisms of PCM operational behavior were analyzed: near‐zero adhesion to metal, elastic micro‐adaptation, high thermal stability, and a transformation of the Stribeck curve towards an expanded regime of elastohydrodynamic lubrication (EHL) and mixed lubrication. Their fundamental differences from Babbitt alloys are also presented. A direct influence of these tribological advantages on equipment operational techno‐economic indicators was established. This influence is manifested as reduced direct operational and capital expenditures (OPEX and CAPEX), and lower cost of downtime. An operational action matrix is proposed for the systemic modernization of rotating machinery to maximize the economic benefits from PPB implementation.

  • Open Access

    Quantitative Kinematics of Thermal Transients in Thin-Layer PEEK/CF30 Composite and Implications for Temperature Monitoring of Plain Bearings

    by Nikolay Ovcharenko

    Thermal kinematics in two-layer systems, analogous to those employed in plain bearings, are investigated. The systems are based on a PEEK/CF30 composite, considered an established alternative to traditional babbitt alloys. Experimental modelling of transient and quasi-steady-state heat transfer regimes was performed on a test bench implementing a one-dimensional heat conduction model within multi-layered media. Samples included babbitt alloy and polymer coatings with thicknesses of 0.40, 0.46, and 1.92 mm. A phenomenological model of heat transfer regimes is proposed, encompassing five sequential phases that represent a complete operating cycle of plain bearing temperature traces. The observed constants of temperature deviations and phase lags are discussed, including their application as instrumental invariants. It was established that reducing the antifriction layer thickness to 0.4 mm significantly lowers its thermal resistance and decreases the time lag by a factor of 5–8. This brings the system response time close to values characteristic of classical babbitt alloys. It is demonstrated that in steady-state hydrodynamic friction regimes, the temperature deviation for thin layers is less than 1 °C, obviating the necessity for algorithmic data compensation. The findings confirm the safety of using polymer materials as the working layer in plain bearings. Despite their lower thermal conductivity and increased time lag, the composites’ high thermal stability margin comfortably compensates for potential temperature deviations, ensuring equipment reliability and safety.

  • Mechanical properties of polymer composite antifriction materials based on polyesteresterketone and babbitts in tensile and compression tests at temperatures above 80°C

    by N. Yu. Ovcharenko

    The article presents the results of tensile and compressive tests of modern antifriction materials for highly loaded friction units at temperatures ranging from 80 to 180°C, aimed at evaluating their applicability in sliding bearings operating under elevated temperature conditions. The tests were conducted in accordance with methods regulated by GOST standards. A comparative assessment was performed of the mechanical properties of polymer-based antifriction materials (PCM) based on polyetheretherketone and babbitt alloys grades B83 and B16 (GOST 1320–74, ISO 4383–91), as well as the TEGOSTAR 738 alloy analogue. The test results revealed fundamentally different strength mechanisms in PCMs and babbitts, as well as differences in their behavior with increasing temperature. PFMs demonstrate significantly higher values of tensile strength, compressive strength, and yield strength compared to babbitt alloys. Babbitts exhibit pronounced plastic behavior already at 80°C, with a distinct yield stage; however, their strength sharply decreases above 100°C, approaching the yield limit, which limits their load-bearing capacity under heated conditions. Although babbitts’ plasticity helps absorb impact loads, it also contributes to frequent failures of babbitt-layered bearings. At temperatures above 120°C, babbitts undergo significant thermal degradation caused by softening of eutectic structures and microstructural deterioration, while reinforced PCMs maintain stable mechanical properties due to the heat resistance of the polymer matrix and effective load distribution through the reinforcing phase. The possibility of tuning PCM properties by selecting matrices, fillers, and additives was noted, opening prospects for adapting materials to specific operating conditions. The combination of lower plastic deformability and high strength gives PCMs better shape retention and stability during failure, while their high thermal stability allows their use over a wider temperature range compared to babbitts. It was confirmed that the imported babbitt TEGOSTAR 738 does not possess significant advantages over domestic grades such as B83, making imported materials economically unjustified. Meanwhile, PCMs outperform babbitts in strength and thermal resistance, enabling an increase in bearing operating temperatures above 200°C while maintaining performance. This opens prospects for using PCMs in modern rotary systems with high reliability requirements. The results confirm the superior mechanical characteristics of PCMs available on the Russian market and the prospects for their application in highly loaded sliding bearings. Further research is recommended to expand testing, including tribological properties and a wider range of materials. The findings can be used by designers and engineering personnel to broaden the range of bearing materials in the design and modernization of highly loaded friction units of rotary equipment to meet modern demands for load capacity, temperature regime, and reliability.

  • INVESTIGATION OF THE HARDNESS OF POLYMER ANTIFRICTION MATERIALS AND BABBITTS AT ELEVATED OPERATING TEMPERATURES

    by N. Yu. Ovcharenko

    The article presents the results of hardness studies using the Brinell and Shore methods for commonly used domestic B83 and B16 babbitt alloys (GOST 1320–74, ISO 4383–91), as well as an alloy analogue of TEGOSTAR 738 grade, and modern industrial polymeric anti-friction composite materials. The studies were conducted according to GOST-regulated methodologies at elevated temperatures (from 80 to 180 C), exceeding the standard operational temperature range, with the aim of evaluating the influence of temperature on the hardness of the materials. Factors limiting the maximum operating temperature of sliding bearings based on the studied materials were identified. An empirical formula is proposed to establish a correlation between Shore D hardness and Brinell hardness for babbitt alloys and a polymer composite based on polyetheretherketone. The obtained data allow assessing of the hardness of the investigated materials under thermal load and can be used by designers and engineering personnel for the informed selection of bearing materials considering operating conditions, service life, and reliability of friction units.

  • He‐Ne laser irradiation of single identified neurons

    by Pavel Balaban, Rinat Esenaliev, Tiina Karu, Elena Kutomkina, Vladilen Letokhov, Alexander Oraevsky, Nikolay Ovcharenko

    Silent (LPa2 and LPa3) and spontaneously active (V3, V5, V17) neurons of subesophageal ganglia of Helix pomatia were irradiated via a 125‐mm fiber probe with a 10‐mW He‐Ne laser (λ = 632.8 nm), and the rate of membrane depolarization, duration of latent period, and probability of spike activity were measured as the functions of light intensity. It was found that silent neurons can not be activated by He‐Ne laser irradiation. When the spontaneously active neurons generating spikes every 7–10 min were irradiated in between their spontaneous spikes, the depolarization of membrane and generation of action potentials occurred as a function of light intensity, I. The probability of spike generation increased until the intensity reached 1 W/cm2, and when 1 = 4 W/cm2 was equal to 1. The depolarization of the membrane had a threshold at I = 0.1 W/cm2, then increased with increasing the intensity, and reached a plateau at I = 0.7 W/cm2 (depolarization rate 0.18 mV/s). Duration of the latent period decreased from 28 s to 17 s when the intensity was increased from 0.05 to 0.3 W/cm2. Further increase of the light intensity, from 0.3 to 1.5 W/cm2, caused a less pronounced change in the duration of the latent period (e.g., latent period equal to 11 s at I = 1.5 W/cm2).