Jain A. R. Tony Benedict
Research Subjects
Jain A. R. Tony Benedict has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Aishwarya Kumaraswamy Pushpa Kumari
Department of Artificial Intelligence and Data Science, Sri Sai Ram Engineering College, West Tambaram, Chennai 600045, India
1 shared publication - Ajith Raj Rajendran
Division of Aerospace Engineering, Karunya Institute of Technology and Sciences, Coimbatore, India
1 shared publication - Ayyanar Subbiah
Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences
1 shared publication - Barath Srinivas Prabakaran
Division of Aerospace Engineering, Karunya Institute of Technology and Sciences, Coimbatore 641114, India
1 shared publication - Janardhan Kamath Sreenarayan
Division of Aerospace Engineering, Karunya Institute of Technology and Sciences, Coimbatore 641114, India
1 shared publication - John Solomon Israel
Panimalar Engineering College (Autonomous), India
1 shared publication
Latest Publications
- Open Access
Multi-Response Optimisation of Process Parameter in Abrasive Water Jet Machining of Machining AA7175/ZrB2 Using Central Composite Design
This study examines the impacts of key abrasive water jet machining (AWJM) parameters on the machinability of AA7175–15 wt.% ZrB2 metal matrix composites produced via a two-step stir casting route. Jet pressure (100–300 MPa), traverse speed (70–130 mm/min), standoff distance (3–5 mm), and abrasive flow rate (250–450 g/min) were systematically varied to evaluate their effects on surface roughness (Ra), kerf taper angle (KA), and material removal rate (MRR). The experimental setup was designed using response surface methodology based on a central composite design (RSM–CCD), enabling both interaction and curvature effects to be assessed. Analysis of variance indicates that jet pressure exerts the strongest influence on MRR, which may be attributed to the increased kinetic energy and penetration capability of abrasive particles at higher pressures. In contrast, traverse speed was found to play a dominant role in controlling surface roughness and kerf geometry. As traverse speed increased, Ra and kerf taper angle tended to rise, likely due to reduced jet–material interaction time and incomplete erosion of the hard ZrB2-reinforced matrix. Abrasive flow rate contributed positively to MRR up to higher levels, although its effect appeared secondary compared to jet pressure. Regression models developed for all machining responses showed strong predictive performance, with coefficients of determination exceeding 0.95 and statistically insignificant lack-of-fit, suggesting adequate representation of the underlying process behaviour within the investigated parameter range. Scanning electron microscopy of the machined surfaces revealed erosion features such as abrasive ploughing, particle pull-out, and striation formation. These surface morphologies are consistent with the observed variations in Ra and kerf characteristics and reflect the combined ductile–brittle erosion response of the composite. Overall, the study identifies optimised AWJM parameter combinations that can improve both surface quality and machining efficiency when processing AA7175–ZrB2 composites.
Open AccessMulti-Response Optimisation of Process Parameter in Abrasive Water Jet Machining of Machining AA7175/ZrB2 Using Central Composite Design
This study examines the impacts of key abrasive water jet machining (AWJM) parameters on the machinability of AA7175–15 wt.% ZrB2 metal matrix composites produced via a two-step stir casting route. Jet pressure (100–300 MPa), traverse speed (70–130 mm/min), standoff distance (3–5 mm), and abrasive flow rate (250–450 g/min) were systematically varied to evaluate their effects on surface roughness (Ra), kerf taper angle (KA), and material removal rate (MRR). The experimental setup was designed using response surface methodology based on a central composite design (RSM–CCD), enabling both interaction and curvature effects to be assessed. Analysis of variance indicates that jet pressure exerts the strongest influence on MRR, which may be attributed to the increased kinetic energy and penetration capability of abrasive particles at higher pressures. In contrast, traverse speed was found to play a dominant role in controlling surface roughness and kerf geometry. As traverse speed increased, Ra and kerf taper angle tended to rise, likely due to reduced jet–material interaction time and incomplete erosion of the hard ZrB2-reinforced matrix. Abrasive flow rate contributed positively to MRR up to higher levels, although its effect appeared secondary compared to jet pressure. Regression models developed for all machining responses showed strong predictive performance, with coefficients of determination exceeding 0.95 and statistically insignificant lack-of-fit, suggesting adequate representation of the underlying process behaviour within the investigated parameter range. Scanning electron microscopy of the machined surfaces revealed erosion features such as abrasive ploughing, particle pull-out, and striation formation. These surface morphologies are consistent with the observed variations in Ra and kerf characteristics and reflect the combined ductile–brittle erosion response of the composite. Overall, the study identifies optimised AWJM parameter combinations that can improve both surface quality and machining efficiency when processing AA7175–ZrB2 composites.
- Open Access
Synergistic Effects of Nanoparticles and Fibers on the Mechanical and Thermal Properties of Epoxy Composites
This study investigates the mechanical and thermal properties of epoxy composites reinforced with aluminum nanoparticles (Al NPs), titanium nanoparticles (Ti NPs), and chopped E-Glass fibers, individually and in hybrid combinations. Thirteen compositions were systematically fabricated and characterized, spanning pure epoxy (PRC0), Al NP-series (PRA1–3), Ti NP-series (PRT1–3), Al NP/E-Glass hybrid series (PRAG1–3), and Ti NP/E-Glass hybrid series (PRTG1–3). The investigation evaluates the effects of these reinforcements on tensile strength, flexural strength, Shore D hardness, thermogravimetric stability, and microstructure. The PRTG2 composite (2 wt% Ti NP + 2 wt% E-Glass fiber) achieved the highest tensile strength of 80 MPa (33.3% improvement over pure epoxy) and the highest flexural strength of 115 MPa (43.75% improvement). These results demonstrate the superior reinforcing efficiency of Ti nanoparticles over Al nanoparticles and the synergistic benefit of combining nanoparticle and fiber reinforcements within a single epoxy matrix.
Open AccessSynergistic Effects of Nanoparticles and Fibers on the Mechanical and Thermal Properties of Epoxy Composites
This study investigates the mechanical and thermal properties of epoxy composites reinforced with aluminum nanoparticles (Al NPs), titanium nanoparticles (Ti NPs), and chopped E-Glass fibers, individually and in hybrid combinations. Thirteen compositions were systematically fabricated and characterized, spanning pure epoxy (PRC0), Al NP-series (PRA1–3), Ti NP-series (PRT1–3), Al NP/E-Glass hybrid series (PRAG1–3), and Ti NP/E-Glass hybrid series (PRTG1–3). The investigation evaluates the effects of these reinforcements on tensile strength, flexural strength, Shore D hardness, thermogravimetric stability, and microstructure. The PRTG2 composite (2 wt% Ti NP + 2 wt% E-Glass fiber) achieved the highest tensile strength of 80 MPa (33.3% improvement over pure epoxy) and the highest flexural strength of 115 MPa (43.75% improvement). These results demonstrate the superior reinforcing efficiency of Ti nanoparticles over Al nanoparticles and the synergistic benefit of combining nanoparticle and fiber reinforcements within a single epoxy matrix.