Mostafa Elkassar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mostafa Elkassar has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Hidehiko Ogata
The United Graduate School of Agricultural Science, Tottori University, Tottori, Japan
3 shared publications Masahiro Hyodo
2 shared publicationsIshii Masayuki
1 shared publication- Masahiro Hyodo
Faculty of Agriculture, Tottori University, Tottori, Japan
1 shared publication Masayuki Ishii
1 shared publication
Latest Publications
- Open Access
Quadratic Characterization of Non-Destructive Internal Loading Responses of Buried RC Pipes Under Different Deterioration and Burial Conditions
Buried reinforced concrete (RC) pipes in water, irrigation and sewer networks are aging, and their renewal must be prioritized without excavation, yet few non-destructive methods measure the stiffness of the pipe–soil system directly. The Internal Loading Method (ILM) loads the pipe wall from inside, and its response has so far been reduced to a single linear slope. This preliminary study examines whether a forced-origin quadratic representation, y = ax2 + bx, can describe load-dependent changes in slope that this linear stiffness cannot, using one RC pipe under four deterioration states and three burial conditions (above ground, 30 cm and a simulated 60 cm; 45 loading cycles). The sign of a gave the direction of curvature of the fitted response (negative in 40 cycles), but its statistical support, evaluated separately, was found in 28 cycles (significantly negative in 27 and significantly positive in one); the magnitude of a did not follow deterioration severity. The mean initial tangent stiffness decreased by 38–51% from the original to the maximum state and was higher at 60 cm than at ground level in all four states of this specimen, by 19% at maximum deterioration and 42–53% otherwise. In this dataset, was the most consistent descriptor examined, and burial must be considered when ILM stiffness is interpreted. The results require confirmation on further specimens.Open AccessQuadratic Characterization of Non-Destructive Internal Loading Responses of Buried RC Pipes Under Different Deterioration and Burial Conditions
Buried reinforced concrete (RC) pipes in water, irrigation and sewer networks are aging, and their renewal must be prioritized without excavation, yet few non-destructive methods measure the stiffness of the pipe–soil system directly. The Internal Loading Method (ILM) loads the pipe wall from inside, and its response has so far been reduced to a single linear slope. This preliminary study examines whether a forced-origin quadratic representation, y = ax2 + bx, can describe load-dependent changes in slope that this linear stiffness cannot, using one RC pipe under four deterioration states and three burial conditions (above ground, 30 cm and a simulated 60 cm; 45 loading cycles). The sign of a gave the direction of curvature of the fitted response (negative in 40 cycles), but its statistical support, evaluated separately, was found in 28 cycles (significantly negative in 27 and significantly positive in one); the magnitude of a did not follow deterioration severity. The mean initial tangent stiffness decreased by 38–51% from the original to the maximum state and was higher at 60 cm than at ground level in all four states of this specimen, by 19% at maximum deterioration and 42–53% otherwise. In this dataset, was the most consistent descriptor examined, and burial must be considered when ILM stiffness is interpreted. The results require confirmation on further specimens. - Open Access
- 10 October 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Experimental assessment of buried RC pipe under varying depth and deterioration states based on load–deformation characteristics using the internal loading method
- 10 October 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Open AccessExperimental assessment of buried RC pipe under varying depth and deterioration states based on load–deformation characteristics using the internal loading method
- Open Access
- 10 July 2026
- Published by Elsevier in SSRN Electronic Journal
Experimental Assessment of Buried RC Pipe Under Varying Depth and Deterioration States Based on Load–Deformation Characteristics Using the Internal Loading Method
Evaluating the structural integrity of buried pipelines is challenging because direct inspection is difficult and soil–structure interaction influences behavior. This study investigates the Internal Loading Method (ILM) as a quantitative diagnostic technique for reinforced concrete (RC) pipes under varying burial and deterioration conditions. An RC pipe (inner diameter: 250mm; wall thickness: 30mm) was tested using a manual Internal Loading Device (ILD) in a soil box at three burial depths — ground level, 30cm, and 60cm — and four deterioration states, from sound to severely damaged. Internal load was applied by the ILD while load–deformation responses and strains were recorded. Pipe–soil system stiffness was quantified from the elastic–range load–deformation response, and its variation with deterioration state and burial depth was evaluated. The results show that the slope of the load–deformation curve, representing pipe–soil system stiffness, decreases consistently as deterioration increases. At the same burial depth, the slope for a minimally deteriorated pipe was up to 13.5% lower than that of an intact pipe, with this reduction becoming more pronounced under deeper burial. Conversely, increasing burial depth generally enhanced system stiffness through soil confinement; however, this beneficial effect diminished progressively as structural damage accumulated, becoming negligible in the severely damaged state. Furthermore, ILM detected stiffness variations across all tested deterioration states and burial depths, and a diagnostic load–deformation chart was developed to relate in–situ stiffness to structural condition. These findings establish ILM as a practical, non–destructive tool for rehabilitation prioritization in RC pipeline management.
- 10 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessExperimental Assessment of Buried RC Pipe Under Varying Depth and Deterioration States Based on Load–Deformation Characteristics Using the Internal Loading Method
Evaluating the structural integrity of buried pipelines is challenging because direct inspection is difficult and soil–structure interaction influences behavior. This study investigates the Internal Loading Method (ILM) as a quantitative diagnostic technique for reinforced concrete (RC) pipes under varying burial and deterioration conditions. An RC pipe (inner diameter: 250mm; wall thickness: 30mm) was tested using a manual Internal Loading Device (ILD) in a soil box at three burial depths — ground level, 30cm, and 60cm — and four deterioration states, from sound to severely damaged. Internal load was applied by the ILD while load–deformation responses and strains were recorded. Pipe–soil system stiffness was quantified from the elastic–range load–deformation response, and its variation with deterioration state and burial depth was evaluated. The results show that the slope of the load–deformation curve, representing pipe–soil system stiffness, decreases consistently as deterioration increases. At the same burial depth, the slope for a minimally deteriorated pipe was up to 13.5% lower than that of an intact pipe, with this reduction becoming more pronounced under deeper burial. Conversely, increasing burial depth generally enhanced system stiffness through soil confinement; however, this beneficial effect diminished progressively as structural damage accumulated, becoming negligible in the severely damaged state. Furthermore, ILM detected stiffness variations across all tested deterioration states and burial depths, and a diagnostic load–deformation chart was developed to relate in–situ stiffness to structural condition. These findings establish ILM as a practical, non–destructive tool for rehabilitation prioritization in RC pipeline management.