Elshan Sefidgar Shahanaghi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Elshan Sefidgar Shahanaghi has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Turan Gurgenc
Department of Automotive Engineering, Technology Faculty, Firat University, Elaziğ, Turkey
2 shared publications - Yasin Varol
Department of Automotive Engineering, Faculty of Technology, Fırat University, 23119 Elazig, Türkiye
2 shared publications Asaf Varol
1 shared publication- Asaf Varol
Engineering School of Arts and Sciences, Dalton State College, Dalton, GA 30720, USA
1 shared publication - Ayse Bicer
Department of Bioengineering, Malatya Turgut Ozal University, 44210 Malatya, Türkiye
1 shared publication - Cevher Kursat Macit
School of Aviation, Firat University, Aircraft Airframe-Engine Maintenance, Elazig, Turkey
1 shared publication
Latest Publications
- Open Access
- 18 November 2026
- Published by Elsevier in SSRN Electronic Journal
Yttrium Aluminium Garnet/Decanoic Acid Nanocomposite Phase Change Materials for Passive Thermal Management of an 18650 Li-ion Cell: From Measured Cycling Degradation to CFD Performance
Decanoic acid (DA) based nanocomposite phase change materials (PCMs) containing 0.5–2.0 wt% Y3Al5O12 nanoparticles dispersed with sodium dodecyl sulfate (SDS) were characterised fresh and after 1000 thermal cycles. FT-IR showed a mainly physical incorporation of Y3Al5O12 and an unchanged chemical structure of DA after cycling. Thermal conductivity increased with loading, by 14.2/12.5% (solid/liquid) at 2.0 wt%, and the specific heat was highest at 1.0 wt% (+23.6/27.7%). After 1000 cycles pure DA lost about 6% of its latent heat, whereas the nanocomposites retained 95.0–98.5% of their melting enthalpy. The measured fresh and aged properties were used in a computational fluid dynamics (CFD) model, validated against a fatty acid melting experiment, of an 18650 Li-ion cell wrapped in a 3 mm PCM shell and generating 2 W. Relative to the bare cell, the Al-cased PCM shell extended the time to 45 °C about 3.7-fold. At this point, fresh compositions differed only within the specific heat measurement uncertainty, whereas after 1000 cycles the PCMs with 0.5–1.5 wt% Y3Al5O12 kept this time 3.3–4.7% longer than pure DA, and the aged 1.0 wt% composite matched fresh pure DA (30.1 min). At a second operating point (4 W, 6 mm shell), where the PCM is only partly molten at 45 °C, thermal conductivity was as influential as specific heat and the gain grew with loading, in the fresh state and to +11.4–11.7% at 1.5–2.0 wt% after 1000 cycles. The best loading therefore depended on the operating point.
- 18 November 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessYttrium Aluminium Garnet/Decanoic Acid Nanocomposite Phase Change Materials for Passive Thermal Management of an 18650 Li-ion Cell: From Measured Cycling Degradation to CFD Performance
Decanoic acid (DA) based nanocomposite phase change materials (PCMs) containing 0.5–2.0 wt% Y3Al5O12 nanoparticles dispersed with sodium dodecyl sulfate (SDS) were characterised fresh and after 1000 thermal cycles. FT-IR showed a mainly physical incorporation of Y3Al5O12 and an unchanged chemical structure of DA after cycling. Thermal conductivity increased with loading, by 14.2/12.5% (solid/liquid) at 2.0 wt%, and the specific heat was highest at 1.0 wt% (+23.6/27.7%). After 1000 cycles pure DA lost about 6% of its latent heat, whereas the nanocomposites retained 95.0–98.5% of their melting enthalpy. The measured fresh and aged properties were used in a computational fluid dynamics (CFD) model, validated against a fatty acid melting experiment, of an 18650 Li-ion cell wrapped in a 3 mm PCM shell and generating 2 W. Relative to the bare cell, the Al-cased PCM shell extended the time to 45 °C about 3.7-fold. At this point, fresh compositions differed only within the specific heat measurement uncertainty, whereas after 1000 cycles the PCMs with 0.5–1.5 wt% Y3Al5O12 kept this time 3.3–4.7% longer than pure DA, and the aged 1.0 wt% composite matched fresh pure DA (30.1 min). At a second operating point (4 W, 6 mm shell), where the PCM is only partly molten at 45 °C, thermal conductivity was as influential as specific heat and the gain grew with loading, in the fresh state and to +11.4–11.7% at 1.5–2.0 wt% after 1000 cycles. The best loading therefore depended on the operating point.
- Open Access
Microstructural Evolution, Densification, and Mechanical–Tribological Performance of AlSi12-Modified NiCrBSi Composites Fabricated by Spark Plasma Sintering
The combined effects of low AlSi12 additions on densification, mechanical properties and load-dependent wear in bulk NiCrBSi consolidated by spark plasma sintering (SPS) remain insufficiently established. This study evaluates AlSi12 as a metallic modifier to improve hardness and wear resistance while identifying associated flexural-strength trade-offs. Compositions containing 0, 2, 4, 6 and 8 wt.% AlSi12 were processed at 950 °C under 38 MPa for 240 s in nitrogen. Phase constitution, microstructure, density, hardness, bending strength and dry-sliding wear at 50 and 100 N were examined. The Ni-rich matrix remained dominant, with local Al enrichment. Experimental density decreased from 8.01 to 6.97 g/cm3, whereas nominal relative density was highest, at approximately 98.7–98.9%, for 4–6 wt.% AlSi12. The highest reported mean hardness was 581 HV at 6 wt.%, while the unmodified alloy reached the highest maximum nominal flexural stress in the displayed bending records. The lowest specific wear rates were approximately 2.6 × 10−5 and 2.9 × 10−5 mm3/(N·m) for 6 wt.% at 50 N and 8 wt.% at 100 N, respectively. These findings support composition selection based on the required balance of hardness, flexural strength and load-specific wear resistance.
Open AccessMicrostructural Evolution, Densification, and Mechanical–Tribological Performance of AlSi12-Modified NiCrBSi Composites Fabricated by Spark Plasma Sintering
The combined effects of low AlSi12 additions on densification, mechanical properties and load-dependent wear in bulk NiCrBSi consolidated by spark plasma sintering (SPS) remain insufficiently established. This study evaluates AlSi12 as a metallic modifier to improve hardness and wear resistance while identifying associated flexural-strength trade-offs. Compositions containing 0, 2, 4, 6 and 8 wt.% AlSi12 were processed at 950 °C under 38 MPa for 240 s in nitrogen. Phase constitution, microstructure, density, hardness, bending strength and dry-sliding wear at 50 and 100 N were examined. The Ni-rich matrix remained dominant, with local Al enrichment. Experimental density decreased from 8.01 to 6.97 g/cm3, whereas nominal relative density was highest, at approximately 98.7–98.9%, for 4–6 wt.% AlSi12. The highest reported mean hardness was 581 HV at 6 wt.%, while the unmodified alloy reached the highest maximum nominal flexural stress in the displayed bending records. The lowest specific wear rates were approximately 2.6 × 10−5 and 2.9 × 10−5 mm3/(N·m) for 6 wt.% at 50 N and 8 wt.% at 100 N, respectively. These findings support composition selection based on the required balance of hardness, flexural strength and load-specific wear resistance.
- Open Access
Refractory Nitride, Resilient PCM: Titanium Nitride/RT70 HC Nanocomposites for Medium-Temperature Thermal Energy Storage and Management
This study tailors titanium nitride (TiN)-reinforced RT70 HC nanocomposite phase change materials (PCMs) for medium-temperature thermal energy storage. TiN nanoparticles were incorporated into commercial RT70 HC at 0.1–2.0 wt.% by a two-stage method combining sodium dodecyl sulfate, magnetic stirring, and ultrasonication, and characterized by FT-IR, XRD, SEM-EDX, elemental mapping, DSC, thermal conductivity, Cp, TGA, and 1000-cycle tests. FT-IR and XRD confirmed the physical integration of TiN into RT70 HC without new chemical bonds or secondary phases, and SEM-EDX showed a concentration-dependent dispersion. The phase change temperatures were largely preserved. The latent heat varied non-monotonically with TiN content, increasing at low loadings (0.1–0.5 wt.%) and decreasing at higher loadings. Because each composition was prepared as a single batch and measured on small specimens, the low-loading latent-heat increase (up to about 9%) is indicative rather than statistically proven and may fall within the subsampling variance. The 0.5 wt.% sample reached the highest values of 306/296 J/g in the first cycle and 286/268 J/g after 1000 cycles. The thermal conductivity increased with TiN content, reaching a maximum enhancement of about 24.09% in the liquid phase (0.1785 to 0.2215 W/(m·K) at 80 °C) and 35.7% in the solid phase at 2.0 wt.%, whereas the specific heat capacity was lower at higher loadings, an indicative trade-off given the single-run measurement uncertainty. TGA showed degradation onset temperatures above 240 °C, a wide safety margin relative to the ~72 °C working range. Overall, the 0.1–0.5 wt.% formulations offered the most balanced thermal performance for medium-temperature applications.
Open AccessRefractory Nitride, Resilient PCM: Titanium Nitride/RT70 HC Nanocomposites for Medium-Temperature Thermal Energy Storage and Management
This study tailors titanium nitride (TiN)-reinforced RT70 HC nanocomposite phase change materials (PCMs) for medium-temperature thermal energy storage. TiN nanoparticles were incorporated into commercial RT70 HC at 0.1–2.0 wt.% by a two-stage method combining sodium dodecyl sulfate, magnetic stirring, and ultrasonication, and characterized by FT-IR, XRD, SEM-EDX, elemental mapping, DSC, thermal conductivity, Cp, TGA, and 1000-cycle tests. FT-IR and XRD confirmed the physical integration of TiN into RT70 HC without new chemical bonds or secondary phases, and SEM-EDX showed a concentration-dependent dispersion. The phase change temperatures were largely preserved. The latent heat varied non-monotonically with TiN content, increasing at low loadings (0.1–0.5 wt.%) and decreasing at higher loadings. Because each composition was prepared as a single batch and measured on small specimens, the low-loading latent-heat increase (up to about 9%) is indicative rather than statistically proven and may fall within the subsampling variance. The 0.5 wt.% sample reached the highest values of 306/296 J/g in the first cycle and 286/268 J/g after 1000 cycles. The thermal conductivity increased with TiN content, reaching a maximum enhancement of about 24.09% in the liquid phase (0.1785 to 0.2215 W/(m·K) at 80 °C) and 35.7% in the solid phase at 2.0 wt.%, whereas the specific heat capacity was lower at higher loadings, an indicative trade-off given the single-run measurement uncertainty. TGA showed degradation onset temperatures above 240 °C, a wide safety margin relative to the ~72 °C working range. Overall, the 0.1–0.5 wt.% formulations offered the most balanced thermal performance for medium-temperature applications.