Praicy Ann Joseph
Research Subjects
Research Interests
Praicy Ann Joseph has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Jens Gutzmer
Helmholtz-Zentrum Dresden-Rossendorf, Helmholtz Institute Freiberg for Resource Technology, Freiberg, Germany
2 shared publications - Abrar Kabir1 shared publication
- Ajay Bhagwan Patil
Bhabha Atomic Research Centre
1 shared publication - Alexandros Charitos
TU Bergakademie Freiberg
1 shared publication - Axel D. Renno
Helmholtz-Zentrum Dresden-Rossendorf, Helmholtz Institute Freiberg for Resource Technology, Freiberg, Germany
1 shared publication - Doreen Ebert
Helmholtz-Zentrum Dresden-Rossendorf, Helmholtz Institute Freiberg for Resource Technology, Freiberg, Germany
1 shared publication
Latest Publications
- Open Access
- 18 October 2026
- Published by Elsevier in SSRN Electronic Journal
When 3D particle characterization meets mineralogical complexity: CT-based analysis of magnetic separation of skarn ore
X-ray computed tomography has the potential to provide valuable 3D particle data for process mineralogical studies. However, this potential is expected to be limited for mineralogically complex ores, where several minerals have similar X-ray attenuation coefficients. In this study, this limitation is tested using process samples from a mineralogically complex and fine-grained Sn-skarn ore. CT-derived particle datasets were used to assess the efficiency of a magnetic separation process and were compared with data from conventional SEM–EDS-based image analysis. To account for the complex mineralogy, a workflow was developed in which particle-wise CT grey-value histograms were interpreted together with SEM–EDS mineralogy and calculated linear X-ray attenuation coefficients. This mineralogy-constrained workflow defined five process-relevant groups: gangue minerals, iron oxides, sphalerite, arsenopyrite, and cassiterite.,Within the investigated 100–200 µm particle-size fraction, CT results showed that particle geometry had no influence on the particle's magnetic separation behavior. The iron oxide group was effectively enriched in the magnetic product, with good correspondence between CT and SEM–EDS data. Cassiterite, on the other hand, was identified with high confidence because of its high attenuation, but CT-derived cassiterite liberation and stream-wise interpretation were found to deviate systematically from the SEM–EDS results. These deviations were attributed to poor detection of fine Fe-bearing associations within cassiterite-rich particles due to the attenuation-related artifacts, leading to an overestimation of cassiterite liberation in CT. The interpretation was further constrained by the small number of relevant particles, resulting in pronounced nugget effects in some samples. Higher-resolution CT could improve the detection of fine mineral associations, but having representative particle counts would require additional scans, increasing analytical and computational requirements. Our study highlights the potential and identifies important limitations of CT as a tool for process mineralogical studies of complex assemblages.
- 18 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessWhen 3D particle characterization meets mineralogical complexity: CT-based analysis of magnetic separation of skarn ore
X-ray computed tomography has the potential to provide valuable 3D particle data for process mineralogical studies. However, this potential is expected to be limited for mineralogically complex ores, where several minerals have similar X-ray attenuation coefficients. In this study, this limitation is tested using process samples from a mineralogically complex and fine-grained Sn-skarn ore. CT-derived particle datasets were used to assess the efficiency of a magnetic separation process and were compared with data from conventional SEM–EDS-based image analysis. To account for the complex mineralogy, a workflow was developed in which particle-wise CT grey-value histograms were interpreted together with SEM–EDS mineralogy and calculated linear X-ray attenuation coefficients. This mineralogy-constrained workflow defined five process-relevant groups: gangue minerals, iron oxides, sphalerite, arsenopyrite, and cassiterite.,Within the investigated 100–200 µm particle-size fraction, CT results showed that particle geometry had no influence on the particle's magnetic separation behavior. The iron oxide group was effectively enriched in the magnetic product, with good correspondence between CT and SEM–EDS data. Cassiterite, on the other hand, was identified with high confidence because of its high attenuation, but CT-derived cassiterite liberation and stream-wise interpretation were found to deviate systematically from the SEM–EDS results. These deviations were attributed to poor detection of fine Fe-bearing associations within cassiterite-rich particles due to the attenuation-related artifacts, leading to an overestimation of cassiterite liberation in CT. The interpretation was further constrained by the small number of relevant particles, resulting in pronounced nugget effects in some samples. Higher-resolution CT could improve the detection of fine mineral associations, but having representative particle counts would require additional scans, increasing analytical and computational requirements. Our study highlights the potential and identifies important limitations of CT as a tool for process mineralogical studies of complex assemblages.
- Open Access
- 24 July 2026
- Published by Elsevier in SSRN Electronic Journal
Valorization of hazardous legacy waste flue dust of former copper smelting using pyrometallurgical pathways
Theisenschlamm is a flue dust, generated as a residue of former industrial copper smelting in Germany. A large volume of this hazardous legacy waste flue dust originated from the smelting of carbonaceous Kupferschiefer ore. Because of various associated environmental risks, the flue dust is currently contained in a sealed storage pond. The objective of this study is to investigate the opportunity of extracting several major metals from Theisenschlamm by a novel pyrometallurgical approach. A two-stage extraction process involving sequential oxidation and reduction was thermochemically designed and validated in laboratory scale with resistance and induction furnaces. Comprehensive material characterization techniques were used to analyze the composition and distribution of metal and slag phases involved in the process. The results demonstrate that zinc and lead were recovered almost completely via the gas phase. Additionally, iron and tin exhibited recovery rates exceeding 95% in the metallic phase. The organic contaminants were thermally decomposed, oxidized and released into the off gas during oxidation stage. The slag generated after reduction was effectively decontaminated, showing low concentrations of residual heavy metals.
- 24 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessValorization of hazardous legacy waste flue dust of former copper smelting using pyrometallurgical pathways
Theisenschlamm is a flue dust, generated as a residue of former industrial copper smelting in Germany. A large volume of this hazardous legacy waste flue dust originated from the smelting of carbonaceous Kupferschiefer ore. Because of various associated environmental risks, the flue dust is currently contained in a sealed storage pond. The objective of this study is to investigate the opportunity of extracting several major metals from Theisenschlamm by a novel pyrometallurgical approach. A two-stage extraction process involving sequential oxidation and reduction was thermochemically designed and validated in laboratory scale with resistance and induction furnaces. Comprehensive material characterization techniques were used to analyze the composition and distribution of metal and slag phases involved in the process. The results demonstrate that zinc and lead were recovered almost completely via the gas phase. Additionally, iron and tin exhibited recovery rates exceeding 95% in the metallic phase. The organic contaminants were thermally decomposed, oxidized and released into the off gas during oxidation stage. The slag generated after reduction was effectively decontaminated, showing low concentrations of residual heavy metals.