Syamimi Mohd Yusoff
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Syamimi Mohd Yusoff has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Abdulmumin Akoredeley Alabi
Department of Mechanical Engineering, Faculty of Engineering, Ahmadu Bello University, Zaria, Kaduna, Nigeria
1 shared publication - Bassey Okon Samuel
Department of Mechanical Engineering, Faculty of Engineering, Ahmadu Bello University, Zaria, Kaduna
1 shared publication Kolawole Israel Komolafe
Department of Mechanical Engineering, Faculty of Engineering, Ahmadu Bello University, Zaria, Kaduna, Nigeria
1 shared publicationNormah Kassim
Faculty of Mechanical Engineering and Technology, Universiti Malaysia Perlis, Arau, Perlis, Malaysia
1 shared publication
Latest Publications
- 6 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (22) , 9319-9335
Predictive and experimental analysis of fracture toughness and density in green aluminum powder compacts: A Taguchi DOE approach
In this paper, we studied the effects of two processing parameters (mass and compaction pressure) on the mode I fracture toughness (KIC) and relative density (RD) of green aluminum powder compacts. The effects of these factors were modeled and optimized using Taguchi design of experiment (DOE). Several complex mathematical models and finite element modeling software have been used to study the responses of K IC and RD in metal powder compacts to variations in compaction pressure and/or powder mass. Taguchi DOE is a robust, user-friendly statistical and modeling tool that is easier to use than most approaches for modeling the behavior of aluminum powder compacts. The L 16 orthogonal array was chosen for the 2-factor and 4-level experiment. The mass of the powder was varied from 3.5 to 5 g while the compaction pressures used were 288.9, 333.4, 377.8, and 422.3 MPa. Results showed that the best combination of factors, yielding an optimal RD of 91%, was 3.5 g of powder and 422.3 MPa of compaction pressure. The optimal K IC of 0.756 MPa · m0.5 was attained at the same conditions. These improvements are directly linked to enhanced particle deformation, reduced interparticle voids (IC and RD of the aluminum powder compact.
- 6 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (22) , 9319-9335
Predictive and experimental analysis of fracture toughness and density in green aluminum powder compacts: A Taguchi DOE approach
In this paper, we studied the effects of two processing parameters (mass and compaction pressure) on the mode I fracture toughness (KIC) and relative density (RD) of green aluminum powder compacts. The effects of these factors were modeled and optimized using Taguchi design of experiment (DOE). Several complex mathematical models and finite element modeling software have been used to study the responses of K IC and RD in metal powder compacts to variations in compaction pressure and/or powder mass. Taguchi DOE is a robust, user-friendly statistical and modeling tool that is easier to use than most approaches for modeling the behavior of aluminum powder compacts. The L 16 orthogonal array was chosen for the 2-factor and 4-level experiment. The mass of the powder was varied from 3.5 to 5 g while the compaction pressures used were 288.9, 333.4, 377.8, and 422.3 MPa. Results showed that the best combination of factors, yielding an optimal RD of 91%, was 3.5 g of powder and 422.3 MPa of compaction pressure. The optimal K IC of 0.756 MPa · m0.5 was attained at the same conditions. These improvements are directly linked to enhanced particle deformation, reduced interparticle voids (IC and RD of the aluminum powder compact.