Aktota Murzagulova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aktota Murzagulova has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Abzal Alikhan
Satbayev University, Almaty 050000, Kazakhstan
1 shared publication - Maratbek Zhuginissov
“Technopark Stroytech” Scientific Research Laboratory of Construction and Building Materials, Satbayev University, Satpayev Street 22, Almaty 050013, Kazakhstan
1 shared publication - Nurbek Tengebayev
“Technopark Stroytech” Scientific Research Laboratory of Construction and Building Materials, Satbayev University, Satpayev Street 22, Almaty 050013, Kazakhstan
1 shared publication - Ruslan Nurlybayev
Institute of Architecture and Civil Engineering, Satbayev University, Almaty, Kazakhstan, Kazakhstan
1 shared publication - Yelzhan S. Orynbekov
Institute of Architecture and Civil Engineering, Satbayev University, 22a Satpaev St., Almaty A03A2C6, Kazakhstan
1 shared publication - Yerlan Khamza
Institute of Architecture and Civil Engineering, Satbayev University, 22a Satpaev St., Almaty A03A2C6, Kazakhstan
1 shared publication
Latest Publications
- Open Access
- 12 August 2026
- Published by MDPI AG in Preprints.org
Hyperpressed Brick Based on Marbleized Limestone Processing Waste
Marbleized limestone processing waste (MLPW) was used as the primary raw material in this study. White Portland cement (CEM I 52.5, M500) and gray Portland cement (CEM I 42.5, M450) were employed as binders. The mixtures were prepared with an MLPW content ranging from 70 to 85 wt.% while maintaining a constant water-to-cement ratio (w/c) of 0.25. The specimens were manufactured by hyperpressing under compaction loads of 200 and 300 kN and subsequently cured for 7 days in a sealed moist environment. Specimens compacted at 200 kN achieved compressive strengths corresponding to brick strength grades M350 and M400. Increasing the compaction load to 300 kN resulted in specimens meeting the requirements of strength grades M400 and M500. When gray Portland cement (M450) was used as the binder at identical MLPW contents and water-to-cement ratio, specimens compacted at 300 kN attained compressive strengths corresponding to grades M400 and M450. The mechanical performance of the hyperpressed bricks produced with both white and gray Portland cement correlated well with the microstructural characteristics observed by scanning electron microscopy (SEM). The average density of all specimens exceeded 2100 kg/m³, allowing the developed materials to be classified as heavyweight concrete. The study aims to develop optimized compositions and a manufacturing technology for hyperpressed bricks based on marbleized limestone processing waste, thereby promoting the sustainable utilization of industrial by-products in the production of high-performance masonry materials.
- 12 August 2026
- Published by MDPI AG in Preprints.org
Open AccessHyperpressed Brick Based on Marbleized Limestone Processing Waste
Marbleized limestone processing waste (MLPW) was used as the primary raw material in this study. White Portland cement (CEM I 52.5, M500) and gray Portland cement (CEM I 42.5, M450) were employed as binders. The mixtures were prepared with an MLPW content ranging from 70 to 85 wt.% while maintaining a constant water-to-cement ratio (w/c) of 0.25. The specimens were manufactured by hyperpressing under compaction loads of 200 and 300 kN and subsequently cured for 7 days in a sealed moist environment. Specimens compacted at 200 kN achieved compressive strengths corresponding to brick strength grades M350 and M400. Increasing the compaction load to 300 kN resulted in specimens meeting the requirements of strength grades M400 and M500. When gray Portland cement (M450) was used as the binder at identical MLPW contents and water-to-cement ratio, specimens compacted at 300 kN attained compressive strengths corresponding to grades M400 and M450. The mechanical performance of the hyperpressed bricks produced with both white and gray Portland cement correlated well with the microstructural characteristics observed by scanning electron microscopy (SEM). The average density of all specimens exceeded 2100 kg/m³, allowing the developed materials to be classified as heavyweight concrete. The study aims to develop optimized compositions and a manufacturing technology for hyperpressed bricks based on marbleized limestone processing waste, thereby promoting the sustainable utilization of industrial by-products in the production of high-performance masonry materials.