Dirk Nelen
Dirk Nelen has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Margot Coppens
Department of Chemical Engineering, KU Leuven, Celestijnenlaan 200J Box 2424, 3001 Leuven, Belgium
2 shared publications - Tom Rommens2 shared publications
- Wim Van Opstal
Unit of Sustainable Materials and Chemistry VITO Mol Belgium
2 shared publications - Ahmad Farid Ehsan
NIGDE UNIVERSITY, INSTITUTE OF SCIENCE
1 shared publication Carlos Marquez
1 shared publication- Dillam Jossue Díaz-Romero
Department of Mechanical Engineering, KU Leuven, Celestijnenlaan 300, Leuven 3000, Belgium
1 shared publication
Latest Publications
- Open Access
- 19 September 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 237
A pragmatic, demand-driven framework to prioritise critical raw material recycling
- 19 September 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 237
Open AccessA pragmatic, demand-driven framework to prioritise critical raw material recycling
- Open Access
- 1 September 2026
- Published by Elsevier in SSRN Electronic Journal
Automated FTIR-XRF and AI-assisted characterisation of mixed WEEE plastic flakes for polymer identification, filler estimation and elemental screening
High-value recycling of WEEE plastics requires particle-level information on polymer identity, filler loading and restricted additives. This study developed an automated FTIR-XRF-AI workflow for characterising mixed WEEE plastic flakes. More than 14,000 flakes were analysed and 2,800 manually verified spectra were used to train an AI classification model for seven WEEE-relevant polymer classes, achieving a test F1 score of 0.993. A separate FTIR-AI model estimated talc and CaCO₃ contents in PP with MAEs of 2.19 wt.%, 1.48 wt.% and 3.08 wt.% for talc, CaCO₃ and total filler content. Integrating FTIR-AI outputs with XRF-based bromine screening and material-flow analysis revealed particle-level links between polymer identity, filler loading, Br concentration and recycling-route distribution. The automated system is commercially available, and the AI and MFA tools are released as open-source resources to support independent application. These resources establish a particle-resolved workflow for improving WEEE plastic sorting, recyclate quality control and compliance-oriented recycling decisions.
- 1 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAutomated FTIR-XRF and AI-assisted characterisation of mixed WEEE plastic flakes for polymer identification, filler estimation and elemental screening
High-value recycling of WEEE plastics requires particle-level information on polymer identity, filler loading and restricted additives. This study developed an automated FTIR-XRF-AI workflow for characterising mixed WEEE plastic flakes. More than 14,000 flakes were analysed and 2,800 manually verified spectra were used to train an AI classification model for seven WEEE-relevant polymer classes, achieving a test F1 score of 0.993. A separate FTIR-AI model estimated talc and CaCO₃ contents in PP with MAEs of 2.19 wt.%, 1.48 wt.% and 3.08 wt.% for talc, CaCO₃ and total filler content. Integrating FTIR-AI outputs with XRF-based bromine screening and material-flow analysis revealed particle-level links between polymer identity, filler loading, Br concentration and recycling-route distribution. The automated system is commercially available, and the AI and MFA tools are released as open-source resources to support independent application. These resources establish a particle-resolved workflow for improving WEEE plastic sorting, recyclate quality control and compliance-oriented recycling decisions.
- Open Access
- 1 January 2025
- Published by Elsevier in SSRN Electronic Journal
A Pragmatic Methodology to Prioritize Critical Raw Material Recovery
Every three years, the European Commission publishes a list of critical raw materials (CRMs), to guide efforts in improving supply chain resilience, including intra-EU extraction and increased material recovery. However, increasing recovery rates for all 34 CRMs across the EU is unfeasible in the short term. To address this challenge, this paper proposes a pragmatic, demand-driven methodology for prioritizing CRM recovery, focusing on actionable and broadly applicable criteria. Unlike traditional approaches based on waste supply or future consumer demand, this methodology includes current industrial demand for primary CRMs that could be replaced by secondary CRMs. This creates a market pull for secondary CRMs, increasing economic viability of recovery efforts. As a first step, CRMs are assessed for recycling feasibility and industrial demand. The result is a selection of CRMs emerging as potential targets to increase recovery. In a second step, put-on-market data for product categories of interest is combined with composition data of the selected CRMs, as researched in the FutuRaM project, to identify future urban mining potential. This approach ensures that waste policies and recovery strategies are driven by industrial needs, encouraging CRM-specific recycling technologies, product-specific collection schemes, and efficient urban mining aligned with market priorities.
- 1 January 2025
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Pragmatic Methodology to Prioritize Critical Raw Material Recovery
Every three years, the European Commission publishes a list of critical raw materials (CRMs), to guide efforts in improving supply chain resilience, including intra-EU extraction and increased material recovery. However, increasing recovery rates for all 34 CRMs across the EU is unfeasible in the short term. To address this challenge, this paper proposes a pragmatic, demand-driven methodology for prioritizing CRM recovery, focusing on actionable and broadly applicable criteria. Unlike traditional approaches based on waste supply or future consumer demand, this methodology includes current industrial demand for primary CRMs that could be replaced by secondary CRMs. This creates a market pull for secondary CRMs, increasing economic viability of recovery efforts. As a first step, CRMs are assessed for recycling feasibility and industrial demand. The result is a selection of CRMs emerging as potential targets to increase recovery. In a second step, put-on-market data for product categories of interest is combined with composition data of the selected CRMs, as researched in the FutuRaM project, to identify future urban mining potential. This approach ensures that waste policies and recovery strategies are driven by industrial needs, encouraging CRM-specific recycling technologies, product-specific collection schemes, and efficient urban mining aligned with market priorities.