Menghua Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Menghua Wu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Bingchun Jiang
College of Mechanical and Electrical Engineering, Guangdong University of Science and Technology, Dongguan 523000, China
1 shared publication - Haoyu Wang
School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China
1 shared publication - Jiayao Li
Dalian Jiaotong University
1 shared publication - Junwei Yin
School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China
1 shared publication - Lulu Wang
Guangdong University of Science and Technology, Dongguan, China
1 shared publication - Qi Cui
Dalian Jiaotong University
1 shared publication
Latest Publications
- 9 September 2026
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 37 (36) , 365903
Design and development of an intelligent tool-holder system for wireless monitoring of transient temperature and dynamic axial force in drilling based on CFRP
During hole-making in carbon-fiber-reinforced polymer composites (CFRP), material anisotropy and interlaminar property mismatch can cause delamination and thermal damage. These damage modes are governed by drilling axial force and drilling temperature. However, synchronous in situ measurement of both parameters remains difficult under high-speed rotation because signal transmission and structural integration are constrained. Here, a force–temperature integrated intelligent tool holder is proposed for CFRP drilling. A pressure sensor is embedded along the tool-holder axis, and a ball-spline mechanism enables stable axial-force transmission and measurement during rotation. K-type thermocouples are arranged near the cutting edge to acquire drilling temperature in situ . Modal analysis shows a first natural frequency of 1020 Hz, avoiding structural resonance during drilling. The STM32-based data acquisition and Wi–Fi wireless transmission system achieves resolutions of 0.2 N and 0.16 ° C. Static tests show maximum relative errors of 5.52% and 2.26%. Drilling tests confirm close agreement with a table-mounted dynamometer, with a maximum peak-value errors of 3.82%. The system enables synchronous in situ monitoring of drilling axial force and drilling temperature.
- 9 September 2026
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 37 (36) , 365903
Design and development of an intelligent tool-holder system for wireless monitoring of transient temperature and dynamic axial force in drilling based on CFRP
During hole-making in carbon-fiber-reinforced polymer composites (CFRP), material anisotropy and interlaminar property mismatch can cause delamination and thermal damage. These damage modes are governed by drilling axial force and drilling temperature. However, synchronous in situ measurement of both parameters remains difficult under high-speed rotation because signal transmission and structural integration are constrained. Here, a force–temperature integrated intelligent tool holder is proposed for CFRP drilling. A pressure sensor is embedded along the tool-holder axis, and a ball-spline mechanism enables stable axial-force transmission and measurement during rotation. K-type thermocouples are arranged near the cutting edge to acquire drilling temperature in situ . Modal analysis shows a first natural frequency of 1020 Hz, avoiding structural resonance during drilling. The STM32-based data acquisition and Wi–Fi wireless transmission system achieves resolutions of 0.2 N and 0.16 ° C. Static tests show maximum relative errors of 5.52% and 2.26%. Drilling tests confirm close agreement with a table-mounted dynamometer, with a maximum peak-value errors of 3.82%. The system enables synchronous in situ monitoring of drilling axial force and drilling temperature.
- Open Access
- 1 January 2026
- Published by Wiley in International Journal of Electrochemistry
- Vol. 2026 (1) , 9255133
Recent Advances in Maskless Localized Electrodeposition Assisted by Jet Flow Field and Laser for Preparing 3D Metal Microstructures and Coatings
Maskless localized electrodeposition (MLED) is a micro–additive manufacturing (micro‐AM) technique in which metals are deposited electrochemically without the use of a physical mask. Through controlled, incremental material growth, the technique can produce two‐dimensional and quasi–three‐dimensional metallic films and coatings, as well as fully three‐dimensional metal microstructures. Its potential applications cover electronic devices, advanced equipment, precision instruments, microsystem fabrication, and localized surface enhancement. A major direction in recent MLED research is the introduction of external physical fields, especially high‐speed jet flow and laser irradiation. These external fields can improve ionic transport and electrochemical reaction behavior, thereby reducing deposition defects, accelerating material growth, producing smoother surfaces, and promoting grain refinement at micro‐ and nanometer scales. Consequently, external field–assisted MLED offers a promising approach to fabricating three‐dimensional metallic features, functional coatings, and metal‐matrix composite coatings with tailored physical and mechanical characteristics, supporting both AM integration and application‐specific performance. This review discusses the working mechanisms, process characteristics, and recent developments of jet‐assisted MLED (Jet‐MLED) and laser‐assisted MLED (Laser‐MLED) for producing metal microstructures and coatings. The respective contributions of jet flow and laser irradiation are analyzed, the capabilities of Jet‐MLED and Laser‐MLED are compared, and the major limitations of both approaches are identified. Remaining scientific questions and possible developments involving multiple coupled energy fields are also considered. These discussions provide guidance for improving deposit quality and material properties. In particular, integrating MLED with appropriately controlled external fields may enhance manufacturing precision and process adaptability, allowing the technique to address increasingly complex tasks in micro‐ and nano‐electrochemical AM. Systematic investigation of Jet‐MLED and Laser‐MLED is therefore essential for the continued development of this field.
- 1 January 2026
- Published by Wiley in International Journal of Electrochemistry
- Vol. 2026 (1) , 9255133
Open AccessRecent Advances in Maskless Localized Electrodeposition Assisted by Jet Flow Field and Laser for Preparing 3D Metal Microstructures and Coatings
Maskless localized electrodeposition (MLED) is a micro–additive manufacturing (micro‐AM) technique in which metals are deposited electrochemically without the use of a physical mask. Through controlled, incremental material growth, the technique can produce two‐dimensional and quasi–three‐dimensional metallic films and coatings, as well as fully three‐dimensional metal microstructures. Its potential applications cover electronic devices, advanced equipment, precision instruments, microsystem fabrication, and localized surface enhancement. A major direction in recent MLED research is the introduction of external physical fields, especially high‐speed jet flow and laser irradiation. These external fields can improve ionic transport and electrochemical reaction behavior, thereby reducing deposition defects, accelerating material growth, producing smoother surfaces, and promoting grain refinement at micro‐ and nanometer scales. Consequently, external field–assisted MLED offers a promising approach to fabricating three‐dimensional metallic features, functional coatings, and metal‐matrix composite coatings with tailored physical and mechanical characteristics, supporting both AM integration and application‐specific performance. This review discusses the working mechanisms, process characteristics, and recent developments of jet‐assisted MLED (Jet‐MLED) and laser‐assisted MLED (Laser‐MLED) for producing metal microstructures and coatings. The respective contributions of jet flow and laser irradiation are analyzed, the capabilities of Jet‐MLED and Laser‐MLED are compared, and the major limitations of both approaches are identified. Remaining scientific questions and possible developments involving multiple coupled energy fields are also considered. These discussions provide guidance for improving deposit quality and material properties. In particular, integrating MLED with appropriately controlled external fields may enhance manufacturing precision and process adaptability, allowing the technique to address increasingly complex tasks in micro‐ and nano‐electrochemical AM. Systematic investigation of Jet‐MLED and Laser‐MLED is therefore essential for the continued development of this field.
- Open Access
Effect of Magnetic Field on Maskless Localized Electrodepositing Three-Dimensional Microstructure of Nano Nickel Crystals
In the intricate process of maskless localized electrodeposition (MLED) for fabricating three-dimensional microstructures, specifically nickel micro-columns with an aspect ratio of 7:1, magnetic fields of defined strength were employed, oriented both parallel and anti-parallel to the electric field. The aim was to achieve nanocrystalline microstructures and elevated deposition rates. A detailed comparative analysis was conducted to examine the volumetric deposition rate, surface morphology, and grain size of the MLED nickel crystal 3D microstructures, both in the absence and presence of the two magnetic field directions, facilitated by a self-assembled experimental setup. The results indicate that the anti-parallel magnetic field significantly boosts the volumetric deposition rate to a notable 19,050.65 μm3/s and refines the grain size, achieving an average size of 24.82 nm. Conversely, the parallel magnetic field is found to enhance the surface morphology of the MLED nickel crystal 3D microstructure.
Open AccessEffect of Magnetic Field on Maskless Localized Electrodepositing Three-Dimensional Microstructure of Nano Nickel Crystals
In the intricate process of maskless localized electrodeposition (MLED) for fabricating three-dimensional microstructures, specifically nickel micro-columns with an aspect ratio of 7:1, magnetic fields of defined strength were employed, oriented both parallel and anti-parallel to the electric field. The aim was to achieve nanocrystalline microstructures and elevated deposition rates. A detailed comparative analysis was conducted to examine the volumetric deposition rate, surface morphology, and grain size of the MLED nickel crystal 3D microstructures, both in the absence and presence of the two magnetic field directions, facilitated by a self-assembled experimental setup. The results indicate that the anti-parallel magnetic field significantly boosts the volumetric deposition rate to a notable 19,050.65 μm3/s and refines the grain size, achieving an average size of 24.82 nm. Conversely, the parallel magnetic field is found to enhance the surface morphology of the MLED nickel crystal 3D microstructure.