Solaiman Mohammad
Research Subjects
Solaiman Mohammad has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Bilal Mansoor
2 shared publications- Muhammad Ahmad2 shared publications
- Rana Abdul Shakoor
Center for Advanced Materials, Qatar University, Doha, Qatar
2 shared publications Aboubakr Abdullah
1 shared publicationAhmad Saadi Samra
1 shared publicationKamran Ali
1 shared publication
Latest Publications
- Open Access
- 28 September 2026
- Published by Elsevier in SSRN Electronic Journal
Ni-P-TiB₂ Electrodeposited Coatings with Improved Mechanical and Corrosion Properties: An Experimental and COMSOL Investigation
High-performance coatings capable of resisting mechanical wear and corrosive degradation are increasingly required for structures exposed to severe service conditions. To address this challenge, Ni-P coatings reinforced with TiB₂ nanoparticles were produced via electrodeposition on mild steel substrates. The TiB₂ content was varied between 0.25 and 1.00 g/L⁻¹, and comprehensive characterization was conducted using structural, morphological, mechanical, tribological, and electrochemical techniques. XRD and microscopic analyses confirmed effective nanoparticle incorporation, with homogeneous dispersion observed up to 0.75 g/L⁻¹. This optimized concentration promoted grain refinement, reduced porosity, and enhanced coating compactness. Mechanical performance improved significantly, with the 0.75 g/L⁻¹ coating showing the highest hardness, corresponding to an increase of approximately 27.53% ± 6% compared with the unreinforced Ni-P layer. Wear testing indicated substantial reductions in both wear rate and friction coefficient, attributed to the rolling and solid-lubricant behavior of TiB₂ nanoparticles. Electrochemical evaluation demonstrated superior corrosion protection, achieving a protection efficiency of ~97.5% and an Rct value of 7.84 kΩ·cm² in 3.5 wt.% NaCl solution. In contrast, excessive TiB₂ addition (1.00g/L⁻¹) led to particle agglomeration and localized structural defects, resulting in diminished performance. Numerical simulations using COMSOL Multiphysics supported these findings by revealing non-uniform current density distribution and thickness variations associated with particle-induced perturbations. These results confirm that properly optimized TiB₂ reinforcement significantly enhances the multifunctional performance of Ni-P coatings designed for harsh operational conditions.
- 28 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNi-P-TiB₂ Electrodeposited Coatings with Improved Mechanical and Corrosion Properties: An Experimental and COMSOL Investigation
High-performance coatings capable of resisting mechanical wear and corrosive degradation are increasingly required for structures exposed to severe service conditions. To address this challenge, Ni-P coatings reinforced with TiB₂ nanoparticles were produced via electrodeposition on mild steel substrates. The TiB₂ content was varied between 0.25 and 1.00 g/L⁻¹, and comprehensive characterization was conducted using structural, morphological, mechanical, tribological, and electrochemical techniques. XRD and microscopic analyses confirmed effective nanoparticle incorporation, with homogeneous dispersion observed up to 0.75 g/L⁻¹. This optimized concentration promoted grain refinement, reduced porosity, and enhanced coating compactness. Mechanical performance improved significantly, with the 0.75 g/L⁻¹ coating showing the highest hardness, corresponding to an increase of approximately 27.53% ± 6% compared with the unreinforced Ni-P layer. Wear testing indicated substantial reductions in both wear rate and friction coefficient, attributed to the rolling and solid-lubricant behavior of TiB₂ nanoparticles. Electrochemical evaluation demonstrated superior corrosion protection, achieving a protection efficiency of ~97.5% and an Rct value of 7.84 kΩ·cm² in 3.5 wt.% NaCl solution. In contrast, excessive TiB₂ addition (1.00g/L⁻¹) led to particle agglomeration and localized structural defects, resulting in diminished performance. Numerical simulations using COMSOL Multiphysics supported these findings by revealing non-uniform current density distribution and thickness variations associated with particle-induced perturbations. These results confirm that properly optimized TiB₂ reinforcement significantly enhances the multifunctional performance of Ni-P coatings designed for harsh operational conditions.
- Open Access
- 29 August 2026
- Published by Elsevier in SSRN Electronic Journal
Mechanical and Corrosion Performance Evaluation and Predictive Modelling of Electroless Ni-P/WC Nanocomposite Coatings
Exposure of steel to corrosive and wear-intensive environments accelerates degradation and shortens service life, motivating protective nanocomposite coatings. In this study, A36 carbon steel was coated with electroless Ni–P/WC nanocomposites containing 0.25, 0.50, and 0.75 g L−1 WC nanoparticles. Structural and morphological analyses confirmed WC incorporation into the Ni–P matrix, while mechanical, tribological, erosive, and corrosion performance was evaluated relative to unreinforced Ni–P. The optimized coating containing 0.50 g L−1 WC increased microhardness from approximately 470 to 876 HV50, corresponding to an 86% improvement, and increased nanoindentation hardness by 56%. It also reduced wear rate by 62% and erosion-crater depth by approximately 50%. Electrochemical testing in 3.5 wt.% NaCl showed a 93% reduction in corrosion current density and a maximum protection efficiency of 92.6%. After 28 days of salt immersion, mass loss decreased from 4.00 to 1.20 mg and corrosion rate from 0.0232 to 0.0070 mm year−1, representing a 70% reduction and confirming improved long-term barrier performance. An exploratory machine-learning framework used WC concentration, deposition time, and bath temperature as inputs, with microhardness and corrosion current density as outputs. Random Forest and K-nearest-neighbor regression were compared as ensemble-based and distance-based approaches. Random Forest performed better, achieving R2 values of approximately 0.85 for both responses and Pearson correlation coefficients above 0.98, whereas KNN showed weaker predictive performance. Feature-importance analysis identified WC concentration as the dominant factor controlling hardness and corrosion response.
- 29 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMechanical and Corrosion Performance Evaluation and Predictive Modelling of Electroless Ni-P/WC Nanocomposite Coatings
Exposure of steel to corrosive and wear-intensive environments accelerates degradation and shortens service life, motivating protective nanocomposite coatings. In this study, A36 carbon steel was coated with electroless Ni–P/WC nanocomposites containing 0.25, 0.50, and 0.75 g L−1 WC nanoparticles. Structural and morphological analyses confirmed WC incorporation into the Ni–P matrix, while mechanical, tribological, erosive, and corrosion performance was evaluated relative to unreinforced Ni–P. The optimized coating containing 0.50 g L−1 WC increased microhardness from approximately 470 to 876 HV50, corresponding to an 86% improvement, and increased nanoindentation hardness by 56%. It also reduced wear rate by 62% and erosion-crater depth by approximately 50%. Electrochemical testing in 3.5 wt.% NaCl showed a 93% reduction in corrosion current density and a maximum protection efficiency of 92.6%. After 28 days of salt immersion, mass loss decreased from 4.00 to 1.20 mg and corrosion rate from 0.0232 to 0.0070 mm year−1, representing a 70% reduction and confirming improved long-term barrier performance. An exploratory machine-learning framework used WC concentration, deposition time, and bath temperature as inputs, with microhardness and corrosion current density as outputs. Random Forest and K-nearest-neighbor regression were compared as ensemble-based and distance-based approaches. Random Forest performed better, achieving R2 values of approximately 0.85 for both responses and Pearson correlation coefficients above 0.98, whereas KNN showed weaker predictive performance. Feature-importance analysis identified WC concentration as the dominant factor controlling hardness and corrosion response.