Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Can Luo has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Research on the Mechanism of High-Performance Aluminum Alloy Casting of Frozen Sand Mold Coupled with Negative Pressure

    by Lei Luo, Can Luo, Qi Lv, Xiao Liang, Liang Wang, Yanqing Su, Jingjie Guo, Fei Mi, Chao Chen, Binbin Wang

    Aluminum–copper alloys, typified by ZL205A (AlCu5MnTiCdV, GB/T 1173), pose severe casting challenges due to their wide solidification interval, poor fluidity, and susceptibility to gas porosity and shrinkage defects. This study introduces a negative-pressure frozen sand mold casting process as a solution to these challenges and systematically quantifies its thermal and microstructural advantages over conventional resin sand and atmospheric frozen sand casting. Using inverse heat conduction analysis of multi-point thermocouple data, the interfacial heat transfer coefficient (IHTC) was quantitatively determined for 14 experimental conditions varying in mold type, pressure level, moisture content (2–6 wt.%), and initial freezing temperature (−20 to −40 °C). The results demonstrate that negative pressure combined with frozen sand molds (6 wt.% moisture, −40 °C) produces the highest active-period average IHTC of 236 W/(m2·K), representing a 2.8-fold increase over atmospheric frozen sand casting and a 1.6-fold increase over negative-pressure resin sand casting. This enhanced thermal driving force promotes grain refinement and effective gas removal, yielding superior mechanical properties: tensile strength of 200.6 MPa and elongation of 9.3% in the as-cast state, and 478.5 MPa and 7.4% after T6 heat treatment. Using the optimized process parameters, a thin-walled cabin component (Ø180 mm × 300 mm, minimum wall thickness 3 mm) was successfully fabricated without defects. These findings establish quantitative process–thermal–microstructure–property relationships for negative-pressure frozen sand casting of wide-solidification-interval aluminum alloys.

  • Interfacial Optimization and Performance Enhancement of CGF / PA Filaments: Insights From Controlled Heat Treatment of Glass Fibers

    by Can Luo, Jing‐Hua Zheng, Yaxing Song, Jiaxun Xu, Yiwei Chen, Congze Fan, Wenzhe Song, Shu Zhu, Xiaobo Han

    Aimed at the key problems of the performance and application of continuous fiber reinforced composite filaments in additive manufacturing, this study clarified that fiber desizing was a key variable affecting the impregnation quality, interface bonding and final filament performance. By systematically characterizing the mechanical properties, microstructure and surface chemistry of glass fibers at different heat treatment temperatures, and analyzing the effects of desizing temperature, mold temperature and traction speed on the forming quality of filaments, the interaction mechanism between fiber surface state and impregnation process conditions was revealed. It was found that the tensile strength of glass fiber decreased significantly after heat treatment above 200°C, and the strength decreased to 787.15 MPa at 350°C, a decrease of 52.12%, which was mainly attributed to the internal structure damage and surface defects of the fiber. Moderate heat treatment (such as 100°C) could increase fiber surface active groups, improve the interface bonding, and improve the comprehensive performance of the filament. This study decoupled the relationship between fiber surface modification, process parameters and composite properties, and provided new insights and experimental basis for directional regulation of composites properties and further improvement of its engineering application potential.

  • Open Access

    Computationally efficient thermo-kinetic modeling for predictive control of melt pool chemistry in additive manufacturing of high-volatile-disparity alloys

    by Qi Lv, Can Luo, Lei Luo, Xiao Liang, Liang Wang, Shuaihu Wei, Hao Guo, Chao Chen, Guotao Zhou, Yalun Xia, et al.

    The control of chemical composition remains the single most formidable challenge restricting the industrial adoption of Additive Manufacturing (AM) for high-volatility-contrast multicomponent alloys like TiAl. The extreme energy density utilized in powder bed fusion or directed energy deposition processes, exemplified here by the electron beam directed energy deposition (EB-DED) technique, triggers severe selective evaporation of volatile components, fundamentally compromising alloy design fidelity. This study presents a paradigmatic shift in AM process modeling by establishing a robust composition-prediction framework. We first analytically establish that Al selective evaporation is the dominant mechanism (Al vapor pressure is 1-2 orders of magnitude higher than Ti), and that the mass loss rate is kinetically controlled by the gas-liquid interface reaction ( K m << β m ). To resolve the non-uniformity inherent to the AM melt pool, we developed an advanced model that integrates fluid-dynamic predictions of melt flow with interface kinetics. This model uniquely accounts for the formation of distinct surface regimes: flow-induced solute-enriched regions (laminar flow) and a surrounding compositionally uniform region (vortex flow). The resulting model, incorporating both the non-uniform temperature field and the heterogeneous solute concentration, successfully forecasts the final alloy chemistry. The model demonstrates exceptional predictive robustness, achieving an experimental deviation of less than 2 at. % when compared to measurements. Based on this validated framework, an optimal processing window (20– 30 mA beam current; 1.5– 2.5 mm/s deposition speed) is defined. This work provides the necessary theoretical foundation and predictive toolset for achieving high compositional fidelity in the additive manufacturing of all alloys susceptible to severe elemental volatilization.