Chang Shu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chang Shu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Bingli Lan
Zhongshan Hecheng Lubrication Materials Co., Ltd., Zhongshan 528403, China
1 shared publication - Hengrui Du
College of Mechanical Engineering, Donghua University, Shanghai 201620, China
1 shared publication - Jianguo Zhang
College of Mechanical Engineering, Donghua University, Shanghai 201620, China
1 shared publication - Jing Wang
College of Mechanical Engineering, Donghua University, Shanghai 201620, China
1 shared publication - Tinyau Wan
College of Mechanical Engineering, Donghua University, Shanghai 201620, China
1 shared publication - Weihao Liu
College of Mechanical Engineering, Donghua University, Shanghai 201620, China
1 shared publication
Latest Publications
- Open Access
- 25 September 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (10) , 365
Effects of Nominal Duty Cycle and Delayed Energization on the Reciprocating Friction and Wear Performance of GCr15 Bearing Steel
Under intermittent source-side excitation, electric-drive systems can maintain mechanical operation, so nominal energization parameters do not directly represent the interfacial electrical state. GCr15 ball-on-disk tests compared dry and polyalphaolefin (PAO 40)-lubricated conditions at 6 N under 5 V, 1 Hz switching. Tests covered nominal duty cycles from D = 0 to 1.00, where D is the ratio of the voltage on-time to the voltage period. Equal-on-time friction tests compared periodic D = 0.50, on→off and off→on. Wear was compared among periodic D = 0.50, off→on, and continuous direct current (DC). Friction increased overall with D. Longer on-time prolonged concurrent microcontact Joule heating and mechanical friction. Dry-sliding wear volume varied non-monotonically, peaking at D = 0.50 with changes in surface-layer removal and O-containing debris retention. Under PAO 40 boundary/mixed lubrication, wear-track width and volume increased monotonically with electrical-heating-related changes in oil film support and separation, microcontact, plowing, and plastic deformation. Equal-on-time friction histories differed. Periodic D = 0.50 and off→on produced similar wear volumes but different morphologies. Dry off→on and continuous DC wear volumes were close. Wear depended on timing and interface state at energization. Interface evolution altered contact resistance and voltage division, feeding back on wear. These findings support energization-parameter and bearing wear risk assessment under intermittent source-side excitation.
- 25 September 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (10) , 365
Open AccessEffects of Nominal Duty Cycle and Delayed Energization on the Reciprocating Friction and Wear Performance of GCr15 Bearing Steel
Under intermittent source-side excitation, electric-drive systems can maintain mechanical operation, so nominal energization parameters do not directly represent the interfacial electrical state. GCr15 ball-on-disk tests compared dry and polyalphaolefin (PAO 40)-lubricated conditions at 6 N under 5 V, 1 Hz switching. Tests covered nominal duty cycles from D = 0 to 1.00, where D is the ratio of the voltage on-time to the voltage period. Equal-on-time friction tests compared periodic D = 0.50, on→off and off→on. Wear was compared among periodic D = 0.50, off→on, and continuous direct current (DC). Friction increased overall with D. Longer on-time prolonged concurrent microcontact Joule heating and mechanical friction. Dry-sliding wear volume varied non-monotonically, peaking at D = 0.50 with changes in surface-layer removal and O-containing debris retention. Under PAO 40 boundary/mixed lubrication, wear-track width and volume increased monotonically with electrical-heating-related changes in oil film support and separation, microcontact, plowing, and plastic deformation. Equal-on-time friction histories differed. Periodic D = 0.50 and off→on produced similar wear volumes but different morphologies. Dry off→on and continuous DC wear volumes were close. Wear depended on timing and interface state at energization. Interface evolution altered contact resistance and voltage division, feeding back on wear. These findings support energization-parameter and bearing wear risk assessment under intermittent source-side excitation.