Ajinkya K. Patil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ajinkya K. Patil has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Abhijeet N. Kore
Department of Mechanical Engineering, Pimpri Chinchwad College of Engineering Savitribai Phule Pune University Pune Maharashtra India
1 shared publication - Manjunatha G Avalappa
Department of Mechanical Engineering, Atria Institute of Technology, Bengaluru, India
1 shared publication - Randhir Y. Chavan
Department of Mechanical Engineering, K E Society’s, Rajarambapu Institute of Technology, Rajaramnagar, affiliated to Shivaji University, Kolhapur, India
1 shared publication S. V. Chaitanya
Department of Mechanical Engineering AISSMS College of Engineering, Savitribai Phule Pune University Pune Maharashtra India
1 shared publication- Sachin C. Kulkarni
Department of Mechanical Engineering, K. L. S. Gogte Institute of Technology, Belagavi, India
1 shared publication - Sharad D. Patil
Department of Mechanical Engineering, K E Society’s, Rajarambapu Institute of Technology, Rajaramnagar, affiliated to Shivaji University, Kolhapur, India
1 shared publication
Latest Publications
- Open Access
- 17 October 2026
- Published by Springer Nature in Journal of Engineering and Applied Science
- Vol. 73 (1) , 418
Performance analysis of a metal hydride reactor for hydrogen storage using ethylene glycol-based coolants as heat transfer fluids
This study numerically investigates the performance of a hydrogen storage metal hydride reactor using ethylene glycol (EG)-water mixtures as Heat Transfer Fluid (HTF). A comprehensive numerical model was developed and validated against published experimental data demonstrating satisfactory agreement between the numerical predictions and the published experimental data for the validated water-cooled absorption process. The primary outcome of the investigation is the evaluation of the hydrogen storage cycle time which is reflective of absorption/desorption kinetics in the metal hydride reactor. The performance of a metal hydride reactor employing ethylene glycol–water mixtures as heat transfer fluids was numerically investigated under realistic operating conditions. The validation yielded a coefficient of determination of R 2 = 0.987 a maximum deviation of 3.51%, an average deviation of 1.54%, and a root-mean-square error of 6.14 K. For the assumed values, pure EG had the shortest cycle times of 285 s absorption time, 880 s desorption time, and 1165 s total cycle time. This represents a 10.7% cycle time saving relative to water. However, the intermediate EG-water mixtures had rather low savings in cycle time, ranging from 3.1% to 3.6%. These results show that the selection of the coolant depends on cycle time, viscosity, pressure drop, pumping power and cost. The predicted cycle times for EG-water mixtures and the desorption process are based solely on numerical simulations and require future experimental validation.
- 17 October 2026
- Published by Springer Nature in Journal of Engineering and Applied Science
- Vol. 73 (1) , 418
Open AccessPerformance analysis of a metal hydride reactor for hydrogen storage using ethylene glycol-based coolants as heat transfer fluids
This study numerically investigates the performance of a hydrogen storage metal hydride reactor using ethylene glycol (EG)-water mixtures as Heat Transfer Fluid (HTF). A comprehensive numerical model was developed and validated against published experimental data demonstrating satisfactory agreement between the numerical predictions and the published experimental data for the validated water-cooled absorption process. The primary outcome of the investigation is the evaluation of the hydrogen storage cycle time which is reflective of absorption/desorption kinetics in the metal hydride reactor. The performance of a metal hydride reactor employing ethylene glycol–water mixtures as heat transfer fluids was numerically investigated under realistic operating conditions. The validation yielded a coefficient of determination of R 2 = 0.987 a maximum deviation of 3.51%, an average deviation of 1.54%, and a root-mean-square error of 6.14 K. For the assumed values, pure EG had the shortest cycle times of 285 s absorption time, 880 s desorption time, and 1165 s total cycle time. This represents a 10.7% cycle time saving relative to water. However, the intermediate EG-water mixtures had rather low savings in cycle time, ranging from 3.1% to 3.6%. These results show that the selection of the coolant depends on cycle time, viscosity, pressure drop, pumping power and cost. The predicted cycle times for EG-water mixtures and the desorption process are based solely on numerical simulations and require future experimental validation.
- 4 October 2026
- Published by Wiley in Energy Storage
- Vol. 8 (7) , e70535
Thermo‐Hydraulic Performance Evaluation of a Metal Hydride Hydrogen Storage Reactor Using Non‐Edible Biofluids as Heat Transfer Fluids
Efficient heat management is critical to enhance the hydrogen storage properties in metal hydride (MH) reactors because the process is highly influenced by transient heat and mass transfer. In this study, we employed a 2D transient heat and mass transfer model to numerically investigate the performance of castor, neem, and jatropha oils in hydrogen absorption and desorption processes in an MmNi4.6Al0.4 tubular MH reactor. The time required for hydrogen uptake and release processes was calculated with a hydrogen supply/delivery pressure of 30 bar and hydrogen content criteria of 99% and compared to water under similar conditions. The numerical results matched the available experimental studies within 2.6%. Compared to water, castor, neem, and jatropha oils reduced the overall cycle time by approximately 25%, 20%, and 17%, respectively. Even though castor oil had relatively high viscosity, it required less than 1 W of pump power in the laboratory reactor, which shows that the hydraulic penalty was insignificant compared to the thermal advantages. The sensitivity analysis revealed that the parameters such as the reaction‐rate constant of absorption and the effective thermal conductivity were influential, while the influence of the external heat transfer coefficient and coolant flow rate was relatively small. Compared to existing enhancement techniques where reactor geometry changes or nanoparticles should be added, the novel method uses an unchanged reactor geometry and sustainable biofluids. Overall, castor oil appeared to be the most optimal fluid in terms of thermal performance and hydraulic losses.
- 4 October 2026
- Published by Wiley in Energy Storage
- Vol. 8 (7) , e70535
Thermo‐Hydraulic Performance Evaluation of a Metal Hydride Hydrogen Storage Reactor Using Non‐Edible Biofluids as Heat Transfer Fluids
Efficient heat management is critical to enhance the hydrogen storage properties in metal hydride (MH) reactors because the process is highly influenced by transient heat and mass transfer. In this study, we employed a 2D transient heat and mass transfer model to numerically investigate the performance of castor, neem, and jatropha oils in hydrogen absorption and desorption processes in an MmNi4.6Al0.4 tubular MH reactor. The time required for hydrogen uptake and release processes was calculated with a hydrogen supply/delivery pressure of 30 bar and hydrogen content criteria of 99% and compared to water under similar conditions. The numerical results matched the available experimental studies within 2.6%. Compared to water, castor, neem, and jatropha oils reduced the overall cycle time by approximately 25%, 20%, and 17%, respectively. Even though castor oil had relatively high viscosity, it required less than 1 W of pump power in the laboratory reactor, which shows that the hydraulic penalty was insignificant compared to the thermal advantages. The sensitivity analysis revealed that the parameters such as the reaction‐rate constant of absorption and the effective thermal conductivity were influential, while the influence of the external heat transfer coefficient and coolant flow rate was relatively small. Compared to existing enhancement techniques where reactor geometry changes or nanoparticles should be added, the novel method uses an unchanged reactor geometry and sustainable biofluids. Overall, castor oil appeared to be the most optimal fluid in terms of thermal performance and hydraulic losses.