Tao Gong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tao Gong has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Jiahao Liu
Hunan Yujing Machine Co., Ltd., Yiyang 413001, China
2 shared publications - Jingang Liu
College of Mechanical Engineering and Mechanics, Xiangtan University, Xiangtan 411105, China
2 shared publications - Junhao Hu
Hunan Yujing Machine Co., Ltd., Yiyang 413001, China
2 shared publications - Ming Zhao
Hunan Yujing Machine Co., Ltd., Yiyang 413001, China
2 shared publications - Xuan Zhou
School of Mechanical Engineering and Mechanics, Xiangtan University, Xiangtan 411105, China
2 shared publications - Zhuangzhi Li
Hunan Yujing Machine Co., Ltd., Yiyang 413001, China
2 shared publications
Latest Publications
- Open Access
Mixing Characteristics of a Reciprocating Stirring Device Based on VOF–DPM Coupling
Diamond particles tend to disperse non-uniformly during the electroplating sand-setting process of diamond wire manufacture. To address this problem, the gas–liquid–solid three-phase flow characteristics in a baffled semi-circular reciprocating mixing tank were numerically analyzed by means of CFD(computational fluid dynamics). A VOF–DPM (Volume of Fluid–Discrete Phase Model) coupled gas–liquid–solid model was established to investigate the flow-field evolution within a stirring cycle, the velocity distribution characteristics, and the influence of the reciprocating frequency on mixing performance; the particle mixing uniformity of the reciprocating stirring device was further verified by sampling experiments. The results show that three typical dynamic vortex regions are formed in the tank, located above and below the stirring plate and outside the baffle, and the flow structure evolves periodically with the motion of the stirring plate. The reciprocating motion of the flat plate exerts a pronounced velocity-amplification effect on the fluid: the maximum axial velocity in the tank can reach 1.95 times the maximum velocity of the stirring plate. Increasing the reciprocating frequency raises the overall flow velocity and improves the uniformity of the velocity distribution, but does not change the basic flow pattern. Under the process condition of 0.5 Hz, which was evaluated experimentally by multi-point sampling (the CFD simulations were performed at 0.25, 0.62, and 1.00 Hz), the relative standard deviation of the diamond particle mass fraction is 4.62%, satisfying the requirements of the diamond wire electroplating sand-setting process. The results provide a theoretical basis for the structural optimization and process parameter regulation of reciprocating stirring devices for diamond wire sand-setting.
Open AccessMixing Characteristics of a Reciprocating Stirring Device Based on VOF–DPM Coupling
Diamond particles tend to disperse non-uniformly during the electroplating sand-setting process of diamond wire manufacture. To address this problem, the gas–liquid–solid three-phase flow characteristics in a baffled semi-circular reciprocating mixing tank were numerically analyzed by means of CFD(computational fluid dynamics). A VOF–DPM (Volume of Fluid–Discrete Phase Model) coupled gas–liquid–solid model was established to investigate the flow-field evolution within a stirring cycle, the velocity distribution characteristics, and the influence of the reciprocating frequency on mixing performance; the particle mixing uniformity of the reciprocating stirring device was further verified by sampling experiments. The results show that three typical dynamic vortex regions are formed in the tank, located above and below the stirring plate and outside the baffle, and the flow structure evolves periodically with the motion of the stirring plate. The reciprocating motion of the flat plate exerts a pronounced velocity-amplification effect on the fluid: the maximum axial velocity in the tank can reach 1.95 times the maximum velocity of the stirring plate. Increasing the reciprocating frequency raises the overall flow velocity and improves the uniformity of the velocity distribution, but does not change the basic flow pattern. Under the process condition of 0.5 Hz, which was evaluated experimentally by multi-point sampling (the CFD simulations were performed at 0.25, 0.62, and 1.00 Hz), the relative standard deviation of the diamond particle mass fraction is 4.62%, satisfying the requirements of the diamond wire electroplating sand-setting process. The results provide a theoretical basis for the structural optimization and process parameter regulation of reciprocating stirring devices for diamond wire sand-setting.
- Open Access
Rotating Magnetic Field-Assisted Vertical Sanding Electroplating Process for Diamond Wire
For coarse-diameter electroplated diamond wires, the traditional horizontal sanding process suffers from inhomogeneous circumferential abrasive distribution, a lengthy manufacturing process, and poor production consistency. To address these issues, a pre-plating-free one-step electroplating process based on rotating magnetic field-assisted vertical sanding is proposed. Through the construction of a high-precision multi-process cooperative control system based on a dual-PLC architecture, systematic optimization of the process parameters from pre-treatment and electrodeposition to post-treatment is realized. Combined with the magnetohydrodynamic (MHD) and electrodeposition kinetic theories, the regulation mechanism of the rotating magnetic field-induced micro-convection effect on the mass transfer of the plating bath, particle dispersion, and grain refinement is revealed, and the kinetic principle by which the bottom-to-top vertical wire-running mode improves the circumferential deposition uniformity of abrasive grains on coarse-diameter wires is clarified. The experimental results show that the breaking force and the number of torsion cycles of the prepared diamond wire under the optimized process conditions are increased by 14.33% and 175.80%, respectively, and the properties of the head and tail ends of the wire exhibit high consistency. This study provides theoretical support for the industrial production of high-quality, high-consistency coarse-diameter diamond wires.
Open AccessRotating Magnetic Field-Assisted Vertical Sanding Electroplating Process for Diamond Wire
For coarse-diameter electroplated diamond wires, the traditional horizontal sanding process suffers from inhomogeneous circumferential abrasive distribution, a lengthy manufacturing process, and poor production consistency. To address these issues, a pre-plating-free one-step electroplating process based on rotating magnetic field-assisted vertical sanding is proposed. Through the construction of a high-precision multi-process cooperative control system based on a dual-PLC architecture, systematic optimization of the process parameters from pre-treatment and electrodeposition to post-treatment is realized. Combined with the magnetohydrodynamic (MHD) and electrodeposition kinetic theories, the regulation mechanism of the rotating magnetic field-induced micro-convection effect on the mass transfer of the plating bath, particle dispersion, and grain refinement is revealed, and the kinetic principle by which the bottom-to-top vertical wire-running mode improves the circumferential deposition uniformity of abrasive grains on coarse-diameter wires is clarified. The experimental results show that the breaking force and the number of torsion cycles of the prepared diamond wire under the optimized process conditions are increased by 14.33% and 175.80%, respectively, and the properties of the head and tail ends of the wire exhibit high consistency. This study provides theoretical support for the industrial production of high-quality, high-consistency coarse-diameter diamond wires.