Daulet Zhamsap
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Daulet Zhamsap has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Karibek Tagayevich Sherov
S.Seifullin Kazakh Agro Technical University
2 shared publications - Riza Gabdyssalyk
International School of Engineering, D. Serikbayev East Kazakhstan Technical University, Ust-Kamenogorsk 070003, Kazakhstan
2 shared publications - Alfiya Muzdybayeva
International School of Engineering, D. Serikbayev East Kazakhstan Technical University, Ust-Kamenogorsk 070003, Kazakhstan
1 shared publication - Amina Mukhamedova
International School of Engineering, East Kazakhstan State Technical University, Ust-Kamenogorsk 70004, Kazakhstan
1 shared publication - Kuat Kombayev
International School of Engineering, East Kazakhstan State Technical University, Ust-Kamenogorsk 070004, Kazakhstan
1 shared publication - S. R. Baigereyev
International School of Engineering, D. Serikbayev East Kazakhstan Technical University, Ust-Kamenogorsk 070003, Kazakhstan
1 shared publication
Latest Publications
- Open Access
- 15 November 2026
- Published by MDPI AG in Applied Mechanics
- Vol. 7 (4) , 98
Numerical Investigation of Hardfacing Process Parameters for Gate Valve Restoration with Experimental Characterization of Hardfaced Specimens
Hardfacing is widely used to restore worn gate-valve surfaces, but the choice of process parameters must account for residual stress, distortion, plastic strain, and the heat-affected zone (HAZ). This study investigated the hardfacing of 09G2S steel numerically in Simufact Welding using a Taguchi L9 design for three filler materials, Np-65G, Stoodite 6M, and PrNl-3V14K, giving 27 simulated conditions. The Goldak heat source was calibrated against a theoretical penetration depth of 1.2–1.5 mm. Conditions resulting in metal boiling, an unmelted bead center, or a penetration depth outside 1.0–2.0 mm were excluded. Lower residual stresses were obtained only together with insufficient penetration or overheating. Run 6 was selected for Np-65G (285 MPa; HAZ depth, 4.7 mm) and Stoodite 6M (373 MPa; 4.6 mm), and Run 2 for PrNl-3V14K (289 MPa; 3.5 mm). On a model of a 90-mm-thick gate plate, the selected Np-65G condition gave a penetration depth of only about 0.5 mm; an adjusted condition within the investigated levels (160 A, 12 V, 3 m/h, 200 °C) gave 1.45–1.80 mm with a fully melted bead for both Np-65G and Stoodite 6M. Conditions selected on specimens must therefore be reassessed for the actual component. Specimens hardfaced under industrial conditions were characterized by microscopy and microhardness testing: 386–466 HV0.05 for the Stoodite 6M deposit and 345–440 HV0.05 for Np-65G.
- 15 November 2026
- Published by MDPI AG in Applied Mechanics
- Vol. 7 (4) , 98
Open AccessNumerical Investigation of Hardfacing Process Parameters for Gate Valve Restoration with Experimental Characterization of Hardfaced Specimens
Hardfacing is widely used to restore worn gate-valve surfaces, but the choice of process parameters must account for residual stress, distortion, plastic strain, and the heat-affected zone (HAZ). This study investigated the hardfacing of 09G2S steel numerically in Simufact Welding using a Taguchi L9 design for three filler materials, Np-65G, Stoodite 6M, and PrNl-3V14K, giving 27 simulated conditions. The Goldak heat source was calibrated against a theoretical penetration depth of 1.2–1.5 mm. Conditions resulting in metal boiling, an unmelted bead center, or a penetration depth outside 1.0–2.0 mm were excluded. Lower residual stresses were obtained only together with insufficient penetration or overheating. Run 6 was selected for Np-65G (285 MPa; HAZ depth, 4.7 mm) and Stoodite 6M (373 MPa; 4.6 mm), and Run 2 for PrNl-3V14K (289 MPa; 3.5 mm). On a model of a 90-mm-thick gate plate, the selected Np-65G condition gave a penetration depth of only about 0.5 mm; an adjusted condition within the investigated levels (160 A, 12 V, 3 m/h, 200 °C) gave 1.45–1.80 mm with a fully melted bead for both Np-65G and Stoodite 6M. Conditions selected on specimens must therefore be reassessed for the actual component. Specimens hardfaced under industrial conditions were characterized by microscopy and microhardness testing: 386–466 HV0.05 for the Stoodite 6M deposit and 345–440 HV0.05 for Np-65G.
- Open Access
- 15 October 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (10) , 433
Comparative Study of the Microstructure, Local Elemental Composition, Microhardness, and Dry-Sliding Friction Behavior of Co-Cr-W, Fe-Mn-C, and Fe-Cr-Ni-Mn GTAW Deposits on 09G2S Steel
This study systematically evaluates the microstructural characteristics, cross-sectional microhardness profiles, and dry sliding friction dynamics of Stoodite 6-M, AISI 1065-type (Np-65G, GOST 10543-98), and AISI 307-type stainless steel (Sv-08Cr20Ni9Mn7Ti, GOST 2246-70) coatings deposited on 09G2S low-alloy steel via gas tungsten arc welding (GTAW). Microstructural evolution and elemental distributions were characterized using optical microscopy and SEM/EDS, while functional properties were assessed via cross-sectional Vickers microhardness profiling (HV0.05) and rotary ball-on-disk friction testing. All surfacing systems produced sound, defect-free fusion interfaces, developing cobalt-matrix dendritic, acicular/packet-lath, and fine cellular-dendritic austenitic structures for Stoodite 6-M, AISI 1065, and AISI 307, respectively. The core cladding microhardness peaked in AISI 307 (505 ± 18 to 525 ± 20 HV0.05), which may be associated with its alloy composition and observed microstructural features, followed by Stoodite 6-M (445 ± 15 to 468 ± 12 HV0.05) and AISI 1065 (355 ± 14 to 438 ± 16 HV0.05). Tribological signal analysis revealed a distinct divergence between static mechanical strength and kinetic sliding behavior: AISI 1065 demonstrated the lowest mean steady-state friction coefficient following initial running-in (μmean = 0.532, SD = 0.019–0.023, CV = 3.57–4.28%), whereas Stoodite 6-M exhibited a higher steady-state friction coefficient (μmean = 0.613, SD = 0.022–0.026, CV = 3.60–4.20%) alongside superior running-in stability, and AISI 307 recorded an intermediate value (μmean = 0.566, SD = 0.035–0.041, CV = 6.19–7.17%). These findings demonstrate that microhardness, mean friction force, and signal stability operate as uncoupled material selection parameters. The study defines baseline friction performance under dry contact conditions, emphasizing the necessity of evaluating contact kinetics independently from bulk mechanical hardness.
- 15 October 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (10) , 433
Open AccessComparative Study of the Microstructure, Local Elemental Composition, Microhardness, and Dry-Sliding Friction Behavior of Co-Cr-W, Fe-Mn-C, and Fe-Cr-Ni-Mn GTAW Deposits on 09G2S Steel
This study systematically evaluates the microstructural characteristics, cross-sectional microhardness profiles, and dry sliding friction dynamics of Stoodite 6-M, AISI 1065-type (Np-65G, GOST 10543-98), and AISI 307-type stainless steel (Sv-08Cr20Ni9Mn7Ti, GOST 2246-70) coatings deposited on 09G2S low-alloy steel via gas tungsten arc welding (GTAW). Microstructural evolution and elemental distributions were characterized using optical microscopy and SEM/EDS, while functional properties were assessed via cross-sectional Vickers microhardness profiling (HV0.05) and rotary ball-on-disk friction testing. All surfacing systems produced sound, defect-free fusion interfaces, developing cobalt-matrix dendritic, acicular/packet-lath, and fine cellular-dendritic austenitic structures for Stoodite 6-M, AISI 1065, and AISI 307, respectively. The core cladding microhardness peaked in AISI 307 (505 ± 18 to 525 ± 20 HV0.05), which may be associated with its alloy composition and observed microstructural features, followed by Stoodite 6-M (445 ± 15 to 468 ± 12 HV0.05) and AISI 1065 (355 ± 14 to 438 ± 16 HV0.05). Tribological signal analysis revealed a distinct divergence between static mechanical strength and kinetic sliding behavior: AISI 1065 demonstrated the lowest mean steady-state friction coefficient following initial running-in (μmean = 0.532, SD = 0.019–0.023, CV = 3.57–4.28%), whereas Stoodite 6-M exhibited a higher steady-state friction coefficient (μmean = 0.613, SD = 0.022–0.026, CV = 3.60–4.20%) alongside superior running-in stability, and AISI 307 recorded an intermediate value (μmean = 0.566, SD = 0.035–0.041, CV = 6.19–7.17%). These findings demonstrate that microhardness, mean friction force, and signal stability operate as uncoupled material selection parameters. The study defines baseline friction performance under dry contact conditions, emphasizing the necessity of evaluating contact kinetics independently from bulk mechanical hardness.