VAVokhid N. Akhmedov

Vokhid N. Akhmedov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Vokhid N. Akhmedov has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Valorisation of Waste Guanidine Thiocyanate into a Guanidinium-Modified Silica Sol/Poly(Vinyl Alcohol) Adhesive: CuCl2/Cu0 Synproportionation Route, Colloidal Stability and Antibacterial Performance

    by Oston H. Qudratov, Vokhid N. Akhmedov, Firuz I. Ostonov, Boburbek N. Umarov, Islom A. Beshimov, Shamshod F. Fatilloyev, Nasiba O‘. Sharipova, Bobir B. Olimov

    Guanidine thiocyanate (GT), a solid by-product of guanidine-salt manufacture, combines a valuable antimicrobial guanidinium cation with a toxic, oxidation-sensitive thiocyanate anion. Here, both ions are converted into useful products. In stage I, aqueous GT is treated with CuCl2 and metallic copper at 20–30 °C; Cu2+/Cu0 synproportionation (ΔE° = +1.14 V) precipitates β-CuSCN in 92 % yield without thiocyanate oxidation or acid formation, leaving guanidinium chloride (GuCl) in solution. In stage II, GuCl reacts with acrylic acid; speciation analysis (K ≈ 7•10−11) and FTIR show that the product is a mixture of guanidinium salts and partially polymerised acrylic acid rather than guanidinium acrylate. In a formalin-modified poly(vinyl alcohol) (PVA)/silica sol adhesive, the modifier shifts the ζ-potential of silica from −28.6 to +2.5 mV; at the resulting ionic strength (≈0.26 mol kg−1) DLVO theory predicts no electrostatic barrier, so the 120-day stability is attributed to steric stabilisation by adsorbed PVA. Compared with an unmodified PVAc reference, the adhesive shows 44–62 % higher lap-shear strength (5.2–6.8 MPa), lower 24 h water uptake (1.8 vs. 7.6 %) and antibacterial activity that is 91.8 % retained after washing, at a net raw-material cost of ≈2.1 kUSD t−1.

  • Open Access

    Valorisation of Secondary Petrochemical Feedstocks into a Multicomponent Demulsifier: Sodium Xylenesulfonate from Pyrolysis-Derived Xylene Formulated with Alkaline-Earth Stearates and Waste Motor Oil

    by Bobir Olimov, Bahrom Ramazanov, Vokhid Akhmedov, Shamshod Fatilloyev, Doston Murodov, Khurshid O̒rinov

    Stable water-in-crude-oil emulsions remain a bottleneck in the treatment of heavy Uzbek crudes, and the demulsifiers used at field level are almost entirely imported. Two local secondary streams—the xylene-rich Ustyurt pyrolysis distillate and collected waste motor oil—were converted into a multicomponent demulsifier. Xylene was sulfonated with 98 wt.% H2SO4 and neutralised to sodium xylenesulfonate (SXS), reaching 96.8% isolated yield at 110–120 °C and an acid:xylene molar ratio of 1.34:1. Fixed-time yields gave a linear Arrhenius dependence (R2 = 0.998) with an apparent activation energy of 21.7 kJ mol−1, ΔH‡ = 18.4 kJ mol−1 and ΔS‡ = −262 J mol−1 K−1, indicating a transport-influenced electrophilic substitution. FTIR confirmed the –SO3Na group, and TG/DTA showed only 5.9% mass loss below 415 °C. Of four hydrophilic–lipophilic balance estimates, only the Davies value (14.2) is compatible with the observed water solubility. The optimum formulation KS-6 (30 wt.% SXS, 50 wt.% waste oil, 18 wt.% Ca and 2 wt.% Sr stearate) gave water-separation efficiencies of 81.0, 93.7 and 98.9% at water cuts of 60, 70 and 80 vol.%, exceeding the imported reference ND-12 by factors of 1.18–1.26, and lowered the residual salt content to 125 mg dm−3.