A. D. Mikhailovskikh
A. D. Mikhailovskikh has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Evgeniy V. Bratygin
Ural Research and Design Institute of Mining, Mineral Processing, Metallurgy, Chemistry, and Standardization (JSC Uralmekhanobr)
1 shared publication - K. V. Bulatov
Ural Research and Design Institute of Mining, Mineral Processing, Metallurgy, Chemistry, and Standardization (JSC Uralmekhanobr)
1 shared publication - V. A. Menshchikov
Ural Research and Design Institute of Mining, Mineral Processing, Metallurgy, Chemistry, and Standardization (JSC Uralmekhanobr)
1 shared publication - V. P. Zhukov
Ural Mining and Metallurgical Company (JSC UMMC)
1 shared publication
Latest Publications
- 13 November 2026
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
Physical modeling and mathematical description of gas bubble growth dynamics at a bottom nozzle outlet in a liquid bath in pyrometallurgical reactors
A laboratory setup was developed, and experiments were conducted to investigate gas bubble growth at a bottom nozzle outlet and determine the gas-liquid interfacial area during gas bubbling. Cold-model experiments showed that the growing bubble successively assumes shapes approximating a spherical cap and a spheroid. A mathematical model was developed to determine the bubble growth time, the instantaneous bubble surface area, and the surface area at detachment. For air injection into pure glycerol at gas flow rates of 30 and 60 dm³/h, the model yields calculated total gas–liquid interfacial areas of 0.0073 and 0.0061 m² over bubble growth periods of 0.17 and 0.12 s, respectively. The discrepancies between the experimental and calculated values range from 1.2 to 12.5 %. A balance of the vertical forces acting on individual regions of the bubble surface was formulated, and an inequality was derived to determine the bubble surface area at the onset of detachment from the force balance. The calculated surface areas at detachment are 5.260·10 –4 and 7.572·10 –4 m². Detachment occurs when the total opposing forces decrease to 17.65 and 25.00 mN, respectively. These surface areas are virtually identical to those predicted by the model based on bubble geometry. The effects of non-isothermal conditions and melt properties on the bubble surface area at detachment were assessed for natural gas injection into molten copper smelting slag at 1623 K. The corresponding balanced force magnitudes increase to 55.2 and 68.7 mN, while the bubble surface areas at detachment decrease to 3.32·10 –4 and 5.37·10 –4 m², respectively. The model can be used to interpret kinetic data for heterogeneous metallurgical reactions obtained in laboratory pyrometallurgical experiments involving bottom injection of a gaseous reactant.
- 13 November 2026
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
Physical modeling and mathematical description of gas bubble growth dynamics at a bottom nozzle outlet in a liquid bath in pyrometallurgical reactors
A laboratory setup was developed, and experiments were conducted to investigate gas bubble growth at a bottom nozzle outlet and determine the gas-liquid interfacial area during gas bubbling. Cold-model experiments showed that the growing bubble successively assumes shapes approximating a spherical cap and a spheroid. A mathematical model was developed to determine the bubble growth time, the instantaneous bubble surface area, and the surface area at detachment. For air injection into pure glycerol at gas flow rates of 30 and 60 dm³/h, the model yields calculated total gas–liquid interfacial areas of 0.0073 and 0.0061 m² over bubble growth periods of 0.17 and 0.12 s, respectively. The discrepancies between the experimental and calculated values range from 1.2 to 12.5 %. A balance of the vertical forces acting on individual regions of the bubble surface was formulated, and an inequality was derived to determine the bubble surface area at the onset of detachment from the force balance. The calculated surface areas at detachment are 5.260·10 –4 and 7.572·10 –4 m². Detachment occurs when the total opposing forces decrease to 17.65 and 25.00 mN, respectively. These surface areas are virtually identical to those predicted by the model based on bubble geometry. The effects of non-isothermal conditions and melt properties on the bubble surface area at detachment were assessed for natural gas injection into molten copper smelting slag at 1623 K. The corresponding balanced force magnitudes increase to 55.2 and 68.7 mN, while the bubble surface areas at detachment decrease to 3.32·10 –4 and 5.37·10 –4 m², respectively. The model can be used to interpret kinetic data for heterogeneous metallurgical reactions obtained in laboratory pyrometallurgical experiments involving bottom injection of a gaseous reactant.