Neda Royaei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Neda Royaei has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Taghi Shahrabi
Department of Materials Engineering, Faculty of Engineering, Tarbiat Modares University, P.O. Box: 14115-143, Tehran, Iran
2 shared publications - Yadollah Yaghoubinezhad
Department of Materials Engineering, Birjand University of Technology, Birjand, Iran
2 shared publications
Latest Publications
- 31 May 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (8) , 085530
Corrosion modeling of dimensional stable anode modified by graphene compounds through a response surface methodology
- 31 May 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (8) , 085530
Corrosion modeling of dimensional stable anode modified by graphene compounds through a response surface methodology
- 4 September 2018
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 8 (19) , 4957-4974
The investigation of the electrocatalytic and corrosion behavior of a TiO2–RuO2 anode modified by graphene oxide and reduced graphene oxide nanosheets via a sol–gel method
A unique electrocatalyst composed of a dimensionally stable anode (DSA) of graphene oxide and reduced graphene oxide combined with RuO2 and TiO2 nanoparticles has been synthesized on a titanium substrate through a facile aqueous sol–gel method. The surface morphology, microstructure and composition of the coatings were investigated by field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FT-IR) and inductively coupled plasma optical emission spectroscopy (ICP-OES). The contribution of the graphene compounds into the anode composition to improve the corrosion and electrocatalytic features was investigated by cyclic voltammetry (CV), polarization measurements, electrochemical impedance spectroscopy (EIS) and an accelerated stability test (AST). The most efficient anode passed the maximum electrical charge at about 145.2 mC cm−2, which was 4.5 times higher than the RuO2–TiO2 (RT) coating, in 0.5 M NaCl + 1 M H2SO4 solution and it was found that the specific current density per unit of the actual surface area (is) ratio of chlorine and oxygen evolution for the optimized electrode was about 3 times higher than the RT electrode which indicates the considerable selectivity behavior of this electrode. The charge transfer resistance of the novel DSA reduced to 2.39 kΩ, while the stability and coating lifetime was improved to 7530 h at j = 1.2 A cm−2 which illustrates that graphene oxide can be used to improve the electrocatalytic performance of DSA anodes.
- 4 September 2018
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 8 (19) , 4957-4974
The investigation of the electrocatalytic and corrosion behavior of a TiO2–RuO2 anode modified by graphene oxide and reduced graphene oxide nanosheets via a sol–gel method
A unique electrocatalyst composed of a dimensionally stable anode (DSA) of graphene oxide and reduced graphene oxide combined with RuO2 and TiO2 nanoparticles has been synthesized on a titanium substrate through a facile aqueous sol–gel method. The surface morphology, microstructure and composition of the coatings were investigated by field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FT-IR) and inductively coupled plasma optical emission spectroscopy (ICP-OES). The contribution of the graphene compounds into the anode composition to improve the corrosion and electrocatalytic features was investigated by cyclic voltammetry (CV), polarization measurements, electrochemical impedance spectroscopy (EIS) and an accelerated stability test (AST). The most efficient anode passed the maximum electrical charge at about 145.2 mC cm−2, which was 4.5 times higher than the RuO2–TiO2 (RT) coating, in 0.5 M NaCl + 1 M H2SO4 solution and it was found that the specific current density per unit of the actual surface area (is) ratio of chlorine and oxygen evolution for the optimized electrode was about 3 times higher than the RT electrode which indicates the considerable selectivity behavior of this electrode. The charge transfer resistance of the novel DSA reduced to 2.39 kΩ, while the stability and coating lifetime was improved to 7530 h at j = 1.2 A cm−2 which illustrates that graphene oxide can be used to improve the electrocatalytic performance of DSA anodes.