Janusz Ochonski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Janusz Ochonski has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Maciej Petko
Faculty of Mechanical Engineering and Robotics, AGH University of Science and Technology, Kraków, Poland
4 shared publications - Grzegorz Karpiel
RIOT Sp. z o.o.
2 shared publications Konrad Gac
2 shared publications- Andrzej Klepka
Department of Robotics and Mechatronics, AGH University of Science and Technology, Krakow, Poland
1 shared publication Grzegorz Gora
AGH University of Science and Technology, Dept. of Robotics and Mechatronics, Kraków, Poland
1 shared publicationGrzegorz Góra
1 shared publication
Latest Publications
- 1 August 2016
- Published by Elsevier in Mechatronics
- Vol. 37, 100-111
Trajectory tracking controller of the hybrid robot for milling
- 1 August 2016
- Published by Elsevier in Mechatronics
- Vol. 37, 100-111
Trajectory tracking controller of the hybrid robot for milling
- 1 August 2016
- Published by Elsevier in Mechatronics
- Vol. 37, 89-99
CNC system of the 5-axis hybrid robot for milling
- 1 August 2016
- Published by Elsevier in Mechatronics
- Vol. 37, 89-99
CNC system of the 5-axis hybrid robot for milling
- 1 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 454-458
Trajectory generation for the hybrid robot from G code
A trajectory generator is one of the most important part of a CNC machine control system. It is required to ensure the smooth tool movement and feed rate changes, which can be done by limiting the jerk. The reason of developing the generator was the necessity of providing values of displacement, feed rate (velocity) and acceleration for all axes of milling machine with high sampling frequency required by the control system. The paper presents the generator of the trajectory from G code that can work with the 5 axes CNC milling robot.
- 1 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 454-458
Trajectory generation for the hybrid robot from G code
A trajectory generator is one of the most important part of a CNC machine control system. It is required to ensure the smooth tool movement and feed rate changes, which can be done by limiting the jerk. The reason of developing the generator was the necessity of providing values of displacement, feed rate (velocity) and acceleration for all axes of milling machine with high sampling frequency required by the control system. The paper presents the generator of the trajectory from G code that can work with the 5 axes CNC milling robot.
- 1 June 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21562318,p. 1123-1128
Acceleration of parallel robot trajectory generation in FPGA
A trajectory generator is one of the most important part of CNC (Computer Numerical Control) machine control systems. It has to ensure the smooth tool movement and feed rate changes, which can be done with a limit imposed on the jerk. The paper presents an application of field programmable gate arrays (FPGA) to accelerate calculations needed for trajectory generation from G-code for a three axes parallel milling robot. The paper shows how to decrease the calculation time, preserving required accuracy, by augmenting the arithmetic-logic unit (ALU) of a microprocessor with custom instructions. The hardware implementation of the accelerator is described and results of calculations performed in an Altera FPGA chip are analyzed.
- 1 June 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21562318,p. 1123-1128
Acceleration of parallel robot trajectory generation in FPGA
A trajectory generator is one of the most important part of CNC (Computer Numerical Control) machine control systems. It has to ensure the smooth tool movement and feed rate changes, which can be done with a limit imposed on the jerk. The paper presents an application of field programmable gate arrays (FPGA) to accelerate calculations needed for trajectory generation from G-code for a three axes parallel milling robot. The paper shows how to decrease the calculation time, preserving required accuracy, by augmenting the arithmetic-logic unit (ALU) of a microprocessor with custom instructions. The hardware implementation of the accelerator is described and results of calculations performed in an Altera FPGA chip are analyzed.
- 1 July 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 518, 87-94
Development of Lamb Waves-Based SHM Systems
Guided waves (GW) based methods are a promising tool for structural health monitoring (SHM) of plate-like metallic and composite structures in which high safety standards are required. In this paper we present research with the aim to design and manufacture a prototype of Lamb waves (LW) SHM system. Two approaches can be applied for SHM of plate-like structures. One of them can be based on a sparse array and damage imaging involving incoherent summation of signals envelope. The second approach involves phased arrays with transducers spaced at a distance lower than half wavelength of the excited Lamb-mode. The influence of an arrays parameters on beamforming of Lamb waves is discussed in the case of linear array. It appears that an unequivocal localization of damage on a plate requires a 2D arrays topology; therefore a star-shaped active array was designed and manufactured for the developed SHM system. Two signal processing approaches were applied for that array, the standard one, based on the delay and sum (DAS) synthetic aperture focusing scheme, and the second one, using a self-focusing technique to obtain the separate images for each scatterer existing in the plate.
- 1 July 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 518, 87-94
Development of Lamb Waves-Based SHM Systems
Guided waves (GW) based methods are a promising tool for structural health monitoring (SHM) of plate-like metallic and composite structures in which high safety standards are required. In this paper we present research with the aim to design and manufacture a prototype of Lamb waves (LW) SHM system. Two approaches can be applied for SHM of plate-like structures. One of them can be based on a sparse array and damage imaging involving incoherent summation of signals envelope. The second approach involves phased arrays with transducers spaced at a distance lower than half wavelength of the excited Lamb-mode. The influence of an arrays parameters on beamforming of Lamb waves is discussed in the case of linear array. It appears that an unequivocal localization of damage on a plate requires a 2D arrays topology; therefore a star-shaped active array was designed and manufactured for the developed SHM system. Two signal processing approaches were applied for that array, the standard one, based on the delay and sum (DAS) synthetic aperture focusing scheme, and the second one, using a self-focusing technique to obtain the separate images for each scatterer existing in the plate.