Alexander A. Saprykin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alexander A. Saprykin has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Egor A. Ibragimov
National Research Tomsk Polytechnic University, Tomsk Russian Federation 634050
19 shared publications - Yurii P. Sharkeev
Institute of Strength Physics and Materials Science, Siberian Branch of the Russian Academy of Sciences
10 shared publications - Natalia A. Saprykina
National Research Tomsk Polytechnic University
9 shared publications - Natalia Saprykina
Natl Res Tomsk Polytech Univ, 30 Lenin Ave, Tomsk 634050, Russia
5 shared publications - E. V. Babakova
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia
4 shared publications - Margarita Andreevna Khimich
Laboratory of Nanobioengineering, Institute of Strength Physics and Materials Science of SB RAS, 634055 Tomsk, Russia
4 shared publications
Latest Publications
- 13 September 2024
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 26 (3) , 192-207
The effect of technological parameters on the microstructure and properties of the AlSiMg alloy obtained by selective laser melting
Introduction. The development of additive technologies is aimed at the synthesis of new powder compositions for selective laser melting plants, the study of the effect of mode parameters on the stable quality of products. The purpose of this work is to study the effect of the scanning strategy on the microstructure, elemental composition, porosity and density of specimens obtained by selective laser melting from non-spherical powders (Al — 91 wt. %, Si — 8 wt. %, Mg — 1 wt. %), subjected to special preparation to determine the optimal conditions for selective laser melting. The research methods are methods of X-ray diffraction and X-ray phase analysis, transmission electron microscopy. The paper examines specimens formed using four different scanning strategies. Results and discussions. A promising aluminum alloy AlSi8Mg is developed for selective laser melting. The material has good manufacturability and low powder cost. The technological parameters of melting make it possible to form a thin structure with a low level of porosity. The mechanism of influence of the scanning strategy on porosity, surface morphology, relative density and microstructure is investigated. A specimen from the AlSi8Mg powder composition with a high relative density of 99.97 % is produced by selective laser melting with an energy density of 200 J/mm3, a specimen scanning circuit when the direction of laser movement changes by an angle of 90° each odd layer. It is proved that the density of the AlSiMg alloy depends on the scanning strategy used. The calculated density of the specimen was 2.5 g/cm3, which corresponds to the density of silumin. Analysis of SEM images and maps of the distribution of elements (Al, Mg, Si) of the specimens showed that different specimen formation strategies do not affect the nature of silicon distribution. A unique grain structure is observed in the resulting AlSi8Mg alloy. The melt pool consists of small grains along the border and large grains in the center. The formation of fine grains is explained by the addition of Si and the high cooling rate during selective laser melting.
- 13 September 2024
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 26 (3) , 192-207
The effect of technological parameters on the microstructure and properties of the AlSiMg alloy obtained by selective laser melting
Introduction. The development of additive technologies is aimed at the synthesis of new powder compositions for selective laser melting plants, the study of the effect of mode parameters on the stable quality of products. The purpose of this work is to study the effect of the scanning strategy on the microstructure, elemental composition, porosity and density of specimens obtained by selective laser melting from non-spherical powders (Al — 91 wt. %, Si — 8 wt. %, Mg — 1 wt. %), subjected to special preparation to determine the optimal conditions for selective laser melting. The research methods are methods of X-ray diffraction and X-ray phase analysis, transmission electron microscopy. The paper examines specimens formed using four different scanning strategies. Results and discussions. A promising aluminum alloy AlSi8Mg is developed for selective laser melting. The material has good manufacturability and low powder cost. The technological parameters of melting make it possible to form a thin structure with a low level of porosity. The mechanism of influence of the scanning strategy on porosity, surface morphology, relative density and microstructure is investigated. A specimen from the AlSi8Mg powder composition with a high relative density of 99.97 % is produced by selective laser melting with an energy density of 200 J/mm3, a specimen scanning circuit when the direction of laser movement changes by an angle of 90° each odd layer. It is proved that the density of the AlSiMg alloy depends on the scanning strategy used. The calculated density of the specimen was 2.5 g/cm3, which corresponds to the density of silumin. Analysis of SEM images and maps of the distribution of elements (Al, Mg, Si) of the specimens showed that different specimen formation strategies do not affect the nature of silicon distribution. A unique grain structure is observed in the resulting AlSi8Mg alloy. The melt pool consists of small grains along the border and large grains in the center. The formation of fine grains is explained by the addition of Si and the high cooling rate during selective laser melting.
- 15 March 2024
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 26 (1)
Optimization of selective laser melting modes of powder composition of the AlSiMg system
Introduction. New aluminum-based powder systems are currently being developed for additive manufacturing. The scientists' work is aimed at comprehensive studies of powder production, optimization of conditions for alloy production and formation of three-dimensional specimens with minimal porosity and absence of cracking during selective laser melting. The purpose of this work is the synthesis of an almost spherical Al-Si-Mg composite powder (91 wt. % Al, 8 wt. % Si, 1 wt. % Mg) from aluminum powder PA-4 (GOST 6058-22), silicon powder (GOST 2169-69) and magnesium powder MPF-4 (GOST 6001-79), which were not originally intended for selective laser melting technology. The work also provides for the optimization of selective laser melting modes to obtain an alloy and form three-dimensional specimens with minimal porosity and no cracking. To create a powder composition, powders ranging in size from 20 to 64 μm were selected by sieve analysis and subjected to mechanical mixing in a ball mill in a protective argon medium for one hour. The research methods are methods of X-ray diffraction and X-ray phase analysis, transmission electron microscopy, mechanical tests of microhardness. Studies of the powder composition after mechanical mixing showed that the mixed powder of aluminum, silicon and magnesium is a conglomerate of particles of spherical, oval and irregular shape. Results and discussions. The optimal modes for obtaining a specimen with a minimum porosity of 0.03 % and a microhardness of 1,291 MPa are selective laser melting modes: P = 90 W, V = 225 mm/s, S = 0.08 mm, h = 0.025 mm. The conducted research shows the possibility of synthesizing products from metal powders that are not adapted to processing by selective laser melting and obtaining an alloy with new mechanical properties during laser action.
- 15 March 2024
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 26 (1)
Optimization of selective laser melting modes of powder composition of the AlSiMg system
Introduction. New aluminum-based powder systems are currently being developed for additive manufacturing. The scientists' work is aimed at comprehensive studies of powder production, optimization of conditions for alloy production and formation of three-dimensional specimens with minimal porosity and absence of cracking during selective laser melting. The purpose of this work is the synthesis of an almost spherical Al-Si-Mg composite powder (91 wt. % Al, 8 wt. % Si, 1 wt. % Mg) from aluminum powder PA-4 (GOST 6058-22), silicon powder (GOST 2169-69) and magnesium powder MPF-4 (GOST 6001-79), which were not originally intended for selective laser melting technology. The work also provides for the optimization of selective laser melting modes to obtain an alloy and form three-dimensional specimens with minimal porosity and no cracking. To create a powder composition, powders ranging in size from 20 to 64 μm were selected by sieve analysis and subjected to mechanical mixing in a ball mill in a protective argon medium for one hour. The research methods are methods of X-ray diffraction and X-ray phase analysis, transmission electron microscopy, mechanical tests of microhardness. Studies of the powder composition after mechanical mixing showed that the mixed powder of aluminum, silicon and magnesium is a conglomerate of particles of spherical, oval and irregular shape. Results and discussions. The optimal modes for obtaining a specimen with a minimum porosity of 0.03 % and a microhardness of 1,291 MPa are selective laser melting modes: P = 90 W, V = 225 mm/s, S = 0.08 mm, h = 0.025 mm. The conducted research shows the possibility of synthesizing products from metal powders that are not adapted to processing by selective laser melting and obtaining an alloy with new mechanical properties during laser action.
- 15 December 2022
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 24 (4)
Synthesis of a three-component aluminum-based alloy by selective laser melting
Introduction. The technology of selective laser melting is one of the key technologies in Industry 4.0, which allows manufacturing products of any complex geometric shape, reducing significantly the amount of material used, reducing the lead time and obtaining a new alloy from elementary powders in the melting process. To understand the process of alloy formation under laser exposure, it is necessary to know the initial data of powders, which significantly affect the quality of the products obtained. The purpose of this study is to determine the requirements for the structural-phase state, elemental composition of aluminum, silicon and magnesium powders and further preparation of Al-Si-Mg (Al — 91 wt.%, Si — 8 wt.%, Mg — 1 wt.%) powder mixture for laser synthesis. The initial powders of aluminum PA-4 (GOST 6058-73), silicon (GOST 2169-69) and magnesium MPF-4 (GOST 6001-79) and powder composition Al-Si-Mg are studied using X-ray diffraction and X-ray phase analysis. The shape and sizes of particles are determined by the studies of raster electronic images. By the method of selective laser melting, samples are obtained from a powder composition under constant and pulsed laser exposure. The composition is prepared by mixing powders in a globe mill. Results and discussion. It is shown that the initial powders of aluminum, silicon and magnesium are single-phase. Particles with a size of 20–64 µm, recommended for selective laser melting, are used to obtain a powder composition. By mixing the powders for one hour, spherical particles are obtained, which is preferable for laser melting. The results of grinding the samples after laser melting showed that the samples obtained under constant laser exposure at the following mode parameters: P = 80 W, V = 300 mm/s, s = 90 μm, h = 25 μm have the greatest mechanical strength. Conclusions. The described study shows the possibility of synthesizing products from a powder composition of aluminum, silicon and magnesium by selective laser melting.
- 15 December 2022
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 24 (4)
Synthesis of a three-component aluminum-based alloy by selective laser melting
Introduction. The technology of selective laser melting is one of the key technologies in Industry 4.0, which allows manufacturing products of any complex geometric shape, reducing significantly the amount of material used, reducing the lead time and obtaining a new alloy from elementary powders in the melting process. To understand the process of alloy formation under laser exposure, it is necessary to know the initial data of powders, which significantly affect the quality of the products obtained. The purpose of this study is to determine the requirements for the structural-phase state, elemental composition of aluminum, silicon and magnesium powders and further preparation of Al-Si-Mg (Al — 91 wt.%, Si — 8 wt.%, Mg — 1 wt.%) powder mixture for laser synthesis. The initial powders of aluminum PA-4 (GOST 6058-73), silicon (GOST 2169-69) and magnesium MPF-4 (GOST 6001-79) and powder composition Al-Si-Mg are studied using X-ray diffraction and X-ray phase analysis. The shape and sizes of particles are determined by the studies of raster electronic images. By the method of selective laser melting, samples are obtained from a powder composition under constant and pulsed laser exposure. The composition is prepared by mixing powders in a globe mill. Results and discussion. It is shown that the initial powders of aluminum, silicon and magnesium are single-phase. Particles with a size of 20–64 µm, recommended for selective laser melting, are used to obtain a powder composition. By mixing the powders for one hour, spherical particles are obtained, which is preferable for laser melting. The results of grinding the samples after laser melting showed that the samples obtained under constant laser exposure at the following mode parameters: P = 80 W, V = 300 mm/s, s = 90 μm, h = 25 μm have the greatest mechanical strength. Conclusions. The described study shows the possibility of synthesizing products from a powder composition of aluminum, silicon and magnesium by selective laser melting.
- 30 June 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1065, 169-178
Synthesis of Tree-Component Cobalt-Based Alloy by Selective Laser Melting
The paper presents studies aimed at producing a three-component alloy from the powders of cobalt, chromium and molybdenum (66 wt % Co, 28 wt % Cr, 6 wt % Mo), with a stable phase structure by selective laser melting. At the beginning of the work, the initial powders were graded on sieves with mesh sizes of 20-70 µm. The powder mixtures were obtained by mechanical mixing of various fraction powders and mechanical alloying in a planetary ball mill. The samples were produced using the VARISCAF-100MVS selective laser melting unit. The melting process of powder materials was completed in a chamber filled with inert gas argon after preliminary vacuum degassing. The microhardness analysis of the samples before and after the thermal treatment was completed. The results of phase composition studies, X-ray diffraction analysis, scanning electron microscopy are presented. Examination of the X-ray profiles of the samples proves that the obtained alloy mainly contains the epsilon-phase which improves the hardness and the wear resistance of the product.
- 30 June 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1065, 169-178
Synthesis of Tree-Component Cobalt-Based Alloy by Selective Laser Melting
The paper presents studies aimed at producing a three-component alloy from the powders of cobalt, chromium and molybdenum (66 wt % Co, 28 wt % Cr, 6 wt % Mo), with a stable phase structure by selective laser melting. At the beginning of the work, the initial powders were graded on sieves with mesh sizes of 20-70 µm. The powder mixtures were obtained by mechanical mixing of various fraction powders and mechanical alloying in a planetary ball mill. The samples were produced using the VARISCAF-100MVS selective laser melting unit. The melting process of powder materials was completed in a chamber filled with inert gas argon after preliminary vacuum degassing. The microhardness analysis of the samples before and after the thermal treatment was completed. The results of phase composition studies, X-ray diffraction analysis, scanning electron microscopy are presented. Examination of the X-ray profiles of the samples proves that the obtained alloy mainly contains the epsilon-phase which improves the hardness and the wear resistance of the product.
- Open Access
- 29 April 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (5) , 1159
Advances in Laser Additive Manufacturing of Ti-Nb Alloys: From Nanostructured Powders to Bulk Objects
The additive manufacturing of low elastic modulus alloys that have a certain level of porosity for biomedical needs is a growing area of research. Here, we show the results of manufacturing of porous and dense samples by a laser powder bed fusion (LPBF) of Ti-Nb alloy, using two distinctive fusion strategies. The nanostructured Ti-Nb alloy powders were produced by mechanical alloying and have a nanostructured state with nanosized grains up to 90 nm. The manufactured porous samples have pronounced open porosity and advanced roughness, contrary to dense samples with a relatively smooth surface profile. The structure of both types of samples after LPBF is formed by uniaxial grains having micro- and nanosized features. The inner structure of the porous samples is comprised of an open interconnected system of pores. The volume fraction of isolated porosity is 2 vol. % and the total porosity is 20 vol. %. Cell viability was assessed in vitro for 3 and 7 days using the MG63 cell line. With longer culture periods, cells showed an increased cell density over the entire surface of a porous Ti-Nb sample. Both types of samples are not cytotoxic and could be used for further in vivo studies.
- 29 April 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (5) , 1159
Open AccessAdvances in Laser Additive Manufacturing of Ti-Nb Alloys: From Nanostructured Powders to Bulk Objects
The additive manufacturing of low elastic modulus alloys that have a certain level of porosity for biomedical needs is a growing area of research. Here, we show the results of manufacturing of porous and dense samples by a laser powder bed fusion (LPBF) of Ti-Nb alloy, using two distinctive fusion strategies. The nanostructured Ti-Nb alloy powders were produced by mechanical alloying and have a nanostructured state with nanosized grains up to 90 nm. The manufactured porous samples have pronounced open porosity and advanced roughness, contrary to dense samples with a relatively smooth surface profile. The structure of both types of samples after LPBF is formed by uniaxial grains having micro- and nanosized features. The inner structure of the porous samples is comprised of an open interconnected system of pores. The volume fraction of isolated porosity is 2 vol. % and the total porosity is 20 vol. %. Cell viability was assessed in vitro for 3 and 7 days using the MG63 cell line. With longer culture periods, cells showed an increased cell density over the entire surface of a porous Ti-Nb sample. Both types of samples are not cytotoxic and could be used for further in vivo studies.
- Open Access
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1100 (1) , 012055
Structure and properties of a cobalt-chromium-molybdenum alloy obtained by selective laser melting
Cobalt-based heat-resistant alloys have unique properties that are used in corrosive environments and at high temperatures. The addition of chromium improves resistance to hot corrosion, while molybdenum improves corrosion resistance and strength. When machining a workpiece of a heat-resistant alloy, up to half of the material goes into chips and goes to processing. Modern trends in the development of additive technologies are aimed at saving material, introducing new materials and improving the physical and mechanical characteristics of the resulting products. Selective laser melting (SLM) is one of the additive methods for obtaining bulk metal products and is one of the most promising directions in the development of science and technology in recent years. This paper describes the porosity (the average value was 14 ± 5%), the structure and properties of alloy samples obtained by selective laser melting in the following modes: laser power - 100 W, scanning speed - 350 mm / s, thickness of the applied powder layer - 25 um, scanning step - 100 um, frequency of pulse-periodic laser action (modulations) - 2.5 kHz from a spherical powder of the CoCrMo alloy (66 wt% Co, 28 wt% Cr, 6 wt% Mo).
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1100 (1) , 012055
Open AccessStructure and properties of a cobalt-chromium-molybdenum alloy obtained by selective laser melting
Cobalt-based heat-resistant alloys have unique properties that are used in corrosive environments and at high temperatures. The addition of chromium improves resistance to hot corrosion, while molybdenum improves corrosion resistance and strength. When machining a workpiece of a heat-resistant alloy, up to half of the material goes into chips and goes to processing. Modern trends in the development of additive technologies are aimed at saving material, introducing new materials and improving the physical and mechanical characteristics of the resulting products. Selective laser melting (SLM) is one of the additive methods for obtaining bulk metal products and is one of the most promising directions in the development of science and technology in recent years. This paper describes the porosity (the average value was 14 ± 5%), the structure and properties of alloy samples obtained by selective laser melting in the following modes: laser power - 100 W, scanning speed - 350 mm / s, thickness of the applied powder layer - 25 um, scanning step - 100 um, frequency of pulse-periodic laser action (modulations) - 2.5 kHz from a spherical powder of the CoCrMo alloy (66 wt% Co, 28 wt% Cr, 6 wt% Mo).
- 17 April 2020
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 839, 7-13
Conditions for Quality Dimensions in Direct Laser Melting of Copper
This paper analyzes the effect of SLM parameters on mechanical characteristics and surface roughness of a single-component copper powder. The study reports on appropriate SLM conditions for a single-component copper powder; to form a layer a technique within layer-by-layer selective laser melting is suggested and comprises roughing, semi-finishing and finishing modes. The work establishes a range to vary surface roughness, porosity and ultimate compressive strength of a single-component copper powder by means of laser processing conditions. Rz is variable 332 to 689 μm, porosity ranges approximately 13-39%, and ultimate compressive strength is 8 to 104 МPа.
- 17 April 2020
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 839, 7-13
Conditions for Quality Dimensions in Direct Laser Melting of Copper
This paper analyzes the effect of SLM parameters on mechanical characteristics and surface roughness of a single-component copper powder. The study reports on appropriate SLM conditions for a single-component copper powder; to form a layer a technique within layer-by-layer selective laser melting is suggested and comprises roughing, semi-finishing and finishing modes. The work establishes a range to vary surface roughness, porosity and ultimate compressive strength of a single-component copper powder by means of laser processing conditions. Rz is variable 332 to 689 μm, porosity ranges approximately 13-39%, and ultimate compressive strength is 8 to 104 МPа.
- Open Access
- 2 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 441 (1) , 012044
Analysis and prediction of copper surface roughness obtained by selective laser melting
The paper presents the results of experimental studies of the effect of mechanoactivation of the powder, argon shielding gas and the effect of technological modes of melting: the speed of the laser beam, the power of laser radiation, the scanning step, the preliminary temperature of heating the powder material on the surface roughness of the copper powder material obtained by selective laser melting. Experiments on the melting of copper powder are implemented on the installation of layer-by-layer laser melting of the original design, which allows to adjust all technological modes of melting. The surface roughness is determined on the non-contact digital microscope Olympus LEXT OLS4100. The mathematical dependence of the surface layer roughness of copper powder on the technological modes of melting is obtained on the basis of the theory of experiment planning and static processing of the results. The significant parameters of the regime-the power of laser radiation, the speed of the laser beam, the scanning step affecting the roughness of the layer. The positive effect of mechanical activation of powder material and protective atmosphere on the quality of the surface layer is shown.
- 2 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 441 (1) , 012044
Open AccessAnalysis and prediction of copper surface roughness obtained by selective laser melting
The paper presents the results of experimental studies of the effect of mechanoactivation of the powder, argon shielding gas and the effect of technological modes of melting: the speed of the laser beam, the power of laser radiation, the scanning step, the preliminary temperature of heating the powder material on the surface roughness of the copper powder material obtained by selective laser melting. Experiments on the melting of copper powder are implemented on the installation of layer-by-layer laser melting of the original design, which allows to adjust all technological modes of melting. The surface roughness is determined on the non-contact digital microscope Olympus LEXT OLS4100. The mathematical dependence of the surface layer roughness of copper powder on the technological modes of melting is obtained on the basis of the theory of experiment planning and static processing of the results. The significant parameters of the regime-the power of laser radiation, the speed of the laser beam, the scanning step affecting the roughness of the layer. The positive effect of mechanical activation of powder material and protective atmosphere on the quality of the surface layer is shown.
- 1 January 2017
- Published by Begell House Inc. Publishers in High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
- Vol. 21 (2) , 161-183
SELECTIVE LASER MELTING OF the Ti–(40–50) wt.% Nb ALLOY
Experimental macrosamples of Ti–(40–50) wt.% Nb alloy were produced using a method of selective laser melting (SLM) from a Ti and Nb composite powder obtained by mechanical alloying in a highenergy planetary ball mill from pure titanium and niobium powders. The SLM process of a Ti–Nb alloy was modeled on micro- and macroscale levels. The necessity of additional heating the powder layer and substrate for successful occurrence of the SLM process on the microscale level was shown. Based on the calculations of the temperature field of the powder layer in the course of the SLM process, the modes and parameters of the SLM process required for the production of macrosamples of Ti–Nb system alloys were determined and specified. The Ti–45 wt.% Nb and Ti–48 wt.% Nb alloys formed as a result of SLM have a two-phase state. This state is represented by the matrix phase of β-bcc solid solution of titanium and niobium and by the nonequilibrium martensite α''-phase.
- 1 January 2017
- Published by Begell House Inc. Publishers in High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
- Vol. 21 (2) , 161-183
SELECTIVE LASER MELTING OF the Ti–(40–50) wt.% Nb ALLOY
Experimental macrosamples of Ti–(40–50) wt.% Nb alloy were produced using a method of selective laser melting (SLM) from a Ti and Nb composite powder obtained by mechanical alloying in a highenergy planetary ball mill from pure titanium and niobium powders. The SLM process of a Ti–Nb alloy was modeled on micro- and macroscale levels. The necessity of additional heating the powder layer and substrate for successful occurrence of the SLM process on the microscale level was shown. Based on the calculations of the temperature field of the powder layer in the course of the SLM process, the modes and parameters of the SLM process required for the production of macrosamples of Ti–Nb system alloys were determined and specified. The Ti–45 wt.% Nb and Ti–48 wt.% Nb alloys formed as a result of SLM have a two-phase state. This state is represented by the matrix phase of β-bcc solid solution of titanium and niobium and by the nonequilibrium martensite α''-phase.
- 15 December 2016
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- No. 4,p. 34-42
Investigation of the structure of Ti-40Nb powder alloy obtained by mechanical activation
- 15 December 2016
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- No. 4,p. 34-42
Investigation of the structure of Ti-40Nb powder alloy obtained by mechanical activation