Mohamed Aymen Mahjoub
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohamed Aymen Mahjoub has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Emmanuel Defay
Luxembourg Institute of Science and Technology
2 shared publications - Nicolas Godard
Materials Research and Technology Department, Luxembourg Institute of Science and Technology 1 , 41 rue du Brill, L-4422 Belvaux, Luxembourg
2 shared publications - Sebastjan Glinsek
Smart Materials Unit Luxembourg Institute of Science and Technology 41 rue du Brill L‐4422 Belvaux Luxembourg
2 shared publications - Tony Schenk
Materials Research and Technology Department Luxembourg Institute of Science and Technology (LIST) 41 Rue du Brill L-4422 Belvaux Luxembourg
2 shared publications - Aleksander Matavž
Jozef Stefan Institute
1 shared publication Stephanie Girod
Materials Research and Technology Department Luxembourg Institute of Science and Technology (LIST) 41 Rue du Brill L-4422 Belvaux Luxembourg
1 shared publication
Latest Publications
- Open Access
- 14 February 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 8 (11) , 3740-3747
On the importance of pyrolysis for inkjet-printed oxide piezoelectric thin films
Inkjet printing (IJP) is an attractive technology for the low-cost fabrication of functional metal oxide thin films, such as piezoelectric lead zirconate titanate (PZT). Implementation of the well-established chemical solution deposition method for PZT films in the IJP process comes with challenges, which were the focus of several works in the field. However, adequate pyrolysis conditions are also required for the complete elimination of organic residues from the layers before crystallization. Thanks to an original technique based on infra-red spectroscopy, the present study draws the correlation between the amount of residual organics in pyrolyzed inkjet-printed layers on platinized silicon and the porosity and functional properties of the final films. Pyrolysis at 475 °C for 3 min afforded dense {111}-textured 200 nm-thick PZT layers after crystallization at 700 °C, with state-of-the-art electrical properties (Pr = 23 μC cm−2, Ec = 60 kV cm−1, ε′ = 1000 and tan δ = 0.04). Potential of inkjet printing technology for piezoelectric devices is demonstrated through a simple energy harvesting device, with a 5.8 μW power output for a 6 kΩ resistive load.
- 14 February 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 8 (11) , 3740-3747
Open AccessOn the importance of pyrolysis for inkjet-printed oxide piezoelectric thin films
Inkjet printing (IJP) is an attractive technology for the low-cost fabrication of functional metal oxide thin films, such as piezoelectric lead zirconate titanate (PZT). Implementation of the well-established chemical solution deposition method for PZT films in the IJP process comes with challenges, which were the focus of several works in the field. However, adequate pyrolysis conditions are also required for the complete elimination of organic residues from the layers before crystallization. Thanks to an original technique based on infra-red spectroscopy, the present study draws the correlation between the amount of residual organics in pyrolyzed inkjet-printed layers on platinized silicon and the porosity and functional properties of the final films. Pyrolysis at 475 °C for 3 min afforded dense {111}-textured 200 nm-thick PZT layers after crystallization at 700 °C, with state-of-the-art electrical properties (Pr = 23 μC cm−2, Ec = 60 kV cm−1, ε′ = 1000 and tan δ = 0.04). Potential of inkjet printing technology for piezoelectric devices is demonstrated through a simple energy harvesting device, with a 5.8 μW power output for a 6 kΩ resistive load.
- Open Access
- 29 November 2019
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (3) , 1900626
Toward Thick Piezoelectric HfO2‐Based Films
For HfO2‐based films, which are mainly prepared by atomic layer deposition, the desired ferroelectric (FE) properties typically vanish while extending the thickness beyond a limit of about 50 nm. Herein, the successful fabrication of a 1 μm‐thick piezoelectric La:HfO2 film is demonstrated using chemical solution deposition, paving the way toward sensor and actuator applications. After identifying the optimal La content, the film thickness is increased from 45 nm to 1 μm. Polarization and strain measurements evidence the persistence of the FE properties at all thicknesses and even a slight improvement due to a better orientation of the polar axis at higher thicknesses. Scanning electron microscopy and X‐ray reflectivity reveal a fine‐grained microstructure and a density of only 80% of the theoretical value, which seems to be a common issue of solution‐deposited HfO2‐based films, based on the performed literature survey. Using tilt‐angle‐dependent X‐ray diffraction scans, homogeneous nucleation is found to be the likely root cause of the observed microstructure. It is suggested that this microstructure issue is key for the optimization of cycling stability of solution‐based films to exploit the full potential of the HfO2 for cost‐efficient, thick piezoelectric films.
- 29 November 2019
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (3) , 1900626
Open AccessToward Thick Piezoelectric HfO2‐Based Films
For HfO2‐based films, which are mainly prepared by atomic layer deposition, the desired ferroelectric (FE) properties typically vanish while extending the thickness beyond a limit of about 50 nm. Herein, the successful fabrication of a 1 μm‐thick piezoelectric La:HfO2 film is demonstrated using chemical solution deposition, paving the way toward sensor and actuator applications. After identifying the optimal La content, the film thickness is increased from 45 nm to 1 μm. Polarization and strain measurements evidence the persistence of the FE properties at all thicknesses and even a slight improvement due to a better orientation of the polar axis at higher thicknesses. Scanning electron microscopy and X‐ray reflectivity reveal a fine‐grained microstructure and a density of only 80% of the theoretical value, which seems to be a common issue of solution‐deposited HfO2‐based films, based on the performed literature survey. Using tilt‐angle‐dependent X‐ray diffraction scans, homogeneous nucleation is found to be the likely root cause of the observed microstructure. It is suggested that this microstructure issue is key for the optimization of cycling stability of solution‐based films to exploit the full potential of the HfO2 for cost‐efficient, thick piezoelectric films.