Ronald Kerans
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ronald Kerans has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Craig Przybyla
Air Force Research Laboratory, Materials and Manufacturing Directorate Wright‐Patterson AFB Dayton Ohio USA
1 shared publicationDino Celli
Air Force Research Laboratory, Aerospace Systems Directorate Wright‐Patterson AFB Dayton Ohio USA
1 shared publication- Fang Jiang
School of Aerospace Engineering & Applied Mechanics, Key Laboratory of the Ministry of Education for Advanced Civil Engineering Materials, Tongji University, China
1 shared publication - Gary Ostdiek
Air Force Research Laboratory, Aerospace Systems Directorate Wright‐Patterson AFB Dayton Ohio USA
1 shared publication George Jefferson
Air Force Research Laboratory, Materials and Manufacturing Directorate Wright‐Patterson AFB Dayton Ohio USA
1 shared publicationJennifer Pierce
University of Dayton Research Institute Advanced Composites Division Dayton Ohio USA
1 shared publication
Latest Publications
- 25 June 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (10) , 6646-6666
Intermediate temperature degradation of a SiC/BN/SiC (MI) composite with holes at 500–900°C in steam
Specimens from a Hi‐Nicalon Type S/BN/SiC (MI) ceramic matrix composite with multiple machined holes were subjected to a furnace dwell and then tensile tested. The furnace temperature range was 500–900°C, and the atmosphere was pure steam to approximate the temperature and sea level partial pressure of water vapor in the cooling air going through turbomachinery cooling holes. Exposure of control specimens was done in laboratory air at the same temperatures. Tensile results along with microscopy and spectroscopy showed significant strength degradation in some conditions due primarily to oxidation of the boron nitride fiber coating, with coating volatilization at lower temperatures and probable fiber‐to‐matrix bonding and imposed fiber stresses at higher temperatures. The greatest strength degradation occurred in the 500–600°C steam range. The fiber coating oxidation/volatilization was especially evident near the holes and was exacerbated in the lower temperature tests by porosity networks that were open to the atmosphere at fiber tow ends at the specimen edges and along the inner walls of the holes.
- 25 June 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (10) , 6646-6666
Intermediate temperature degradation of a SiC/BN/SiC (MI) composite with holes at 500–900°C in steam
Specimens from a Hi‐Nicalon Type S/BN/SiC (MI) ceramic matrix composite with multiple machined holes were subjected to a furnace dwell and then tensile tested. The furnace temperature range was 500–900°C, and the atmosphere was pure steam to approximate the temperature and sea level partial pressure of water vapor in the cooling air going through turbomachinery cooling holes. Exposure of control specimens was done in laboratory air at the same temperatures. Tensile results along with microscopy and spectroscopy showed significant strength degradation in some conditions due primarily to oxidation of the boron nitride fiber coating, with coating volatilization at lower temperatures and probable fiber‐to‐matrix bonding and imposed fiber stresses at higher temperatures. The greatest strength degradation occurred in the 500–600°C steam range. The fiber coating oxidation/volatilization was especially evident near the holes and was exacerbated in the lower temperature tests by porosity networks that were open to the atmosphere at fiber tow ends at the specimen edges and along the inner walls of the holes.
- Open Access
- 9 November 2021
- Published by Wiley in International Journal of Ceramic Engineering & Science
- Vol. 4 (1) , 23-37
Modeling stress–strain behavior of ceramic composites
A well‐known model of stress–strain behavior in continuous‐fiber ceramic composites was expanded, corrected, and coded in a popular programming language. Four versions of the code with differing output plot formats are included. They can be pasted into a program file and used without editing. One of them allows observing the changes in the stress–strain curve while varying nearly any of the input properties. The ability to observe or quickly plot and compare curves using different parameters can aid in understanding the roles of constituent and interface properties in composite behavior. It can also aid in inferring unmeasurable properties in actual composites. Comparisons of model output to experiment are presented and discussed.
- 9 November 2021
- Published by Wiley in International Journal of Ceramic Engineering & Science
- Vol. 4 (1) , 23-37
Open AccessModeling stress–strain behavior of ceramic composites
A well‐known model of stress–strain behavior in continuous‐fiber ceramic composites was expanded, corrected, and coded in a popular programming language. Four versions of the code with differing output plot formats are included. They can be pasted into a program file and used without editing. One of them allows observing the changes in the stress–strain curve while varying nearly any of the input properties. The ability to observe or quickly plot and compare curves using different parameters can aid in understanding the roles of constituent and interface properties in composite behavior. It can also aid in inferring unmeasurable properties in actual composites. Comparisons of model output to experiment are presented and discussed.