MZMark Zalyubovskyi

Mark Zalyubovskyi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mark Zalyubovskyi has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • KINEMATIC STUDY OF A FOURTH-CLASS MECHANISM WITH THREE TRANSLATIONAL AND OTHER ROTATIONAL KINEMATIC PAIRS

    by Sergey Koshel, yiv National University of Technology and Design, Ganna Koshel, Mark Zalyubovskyi, Oleksandr Koshel, Open International University of Human Development “Ukraine”, Kyiv National University of Technology and Design

  • СТРУКТУРНИЙ АНАЛІЗ МЕХАНІЗМІВ ЧЕТВЕРТОГО КЛАСУ З ТРЬОМА СКЛАДНИМИ ЛАНКАМИ

    by Сергій Кошель, Ганна Кошель, Марк Залюбовський, Олександр Кошель

    A structural study of a complex planar mechanism of the fourth class with one driving link and a moving closed loop was performed. The contour has the form of a quadrangle, which is formed by three links that have plane-parallel movement and one link that rotates around a fixed axis. The circuit is formed by four links: three connecting rods, two of which are complex links and are located opposite each other, and one rocker, which takes part in the formation of three kinematic pairs. Structurally, the set of six links and nine kinematic pairs, which is the basis of a complex mechanism, belongs to the group of links of the fourth class and the third order. We have developed possible variants of structural groups of links of the fourth class of the third order with a closed circuit, in which the nature of kinematic pairs and their location were taken into account. For various variants of structural groups of links, we obtained structural formulas of structures of mechanisms of the fourth class. We used the method of structural change of the actual leading link of the mechanism with another conditionally possible one. The obtained results of the study allow us to determine the sequence of further studies of the fourth-class mechanism with one structural group of higher-class links in the form of a second-class mechanism with three sequentially connected structural groups of the corresponding class.

  • Design Parameters of the Four-Link Hinged Mechanism of Barreling Machine Drive

    by M. G. Zalyubovskyi, I. V. Panasyuk, S. O. Koshel’, D. O. Lychov


  • FORCE STUDY OF REACTIVE LOADS IN KINEMATIC COUPLES OF A WORKING CAPACITY TURNING MACHINE WITH COMPLEX SPACE MOVEMENT AND VARIABLE VOLUME

    by Mark Zalyubovskyi, Mariia Blazhenko, National University of Food Technologies Open International University of Human Development “Ukraine”, Igor Panasyuk, Kyiv National University of Technology and Design

    High productivity when performing finishing technological operations, as well as technological processes of mixing loose fine-dispersed substances, can be achieved with the use of equipment in which working containers perform complex spatial movement. To date, various types of developed felting machines with complex spatial movement of working containers are known. Each type of such equipment corresponds to the implementation of various felting technological operations – separation of parts from sprues, grinding or polishing of products, cleaning of metal parts from corrosion or mixing of loose fine-dispersed substances. During the operation of the rolling equipment, various reactive loads arise in the kinematic pairs, which depend on the design features of the machines. With the use of the automated design system “SolidWorks”, 3D modeling and further strength research of a model of a rolling machine with a working capacity with complex spatial movement and variable volume was performed. In the kinematic chain of the machine under study, an additional moving connecting rod link with rotational and translational kinematic pairs is used. During the performance of the force study, the reactions in all rotational and translational kinematic pairs were determined, the influence of the change in the interaxial distance of the working capacity and the additional moving link of the connecting rod on the maximum values of the reactions in the kinematic pairs of the machine was investigated. The presented results of analytical studies can be applied in the relevant design bureaus of machine-building enterprises at the stage of designing equipment with complex spatial movement of working capacities and felting technological processes.

  • RESEARCH OF THE CHANGE OF THE MOTION MODES OF THE WORKING ARRAY IN A TURNING MACHINE WITH AN ADDITIONAL MOVEABLE SLIDING LINK DEPENDING ON THE CHANGE OF DESIGN FEATURES

    by Mark Zalyubovskyi, Igor Panasyuk, Kyiv National University of Technology and Design, Dmitro Lychov, Open International University of Human Development “Ukraine”, Ganna Koshel

    With the help of the SolidWorks automated design system, analytical studies of the rolling machine with complex spatial movement of the working capacity of the “Turbula” type, which contains an additional moving link of the slider in its kinematic chain, were performed. On the basis of the analytical studies, the relationship between the change in the modes of movement of the working array in the middle of the container, the value of the angular velocity of the drive shaft, the scale standard size and the ratio of the interaxial distance of the container to the interaxial distance of the forks was determined. The classification of the movement modes of the working massif is presented, in particular, which should include cascade, mixed and waterfall movement modes. Each movement mode corresponds to the implementation of the corresponding types of felting technological operations or mixing of loose fine-dispersed substances. The effect of changing the length of the working capacity, which is characterized by the ratio of the interaxial distance of the working capacity to the interaxial distance of the leading or driven forks of the machine, on the change in the modes of movement of the working array has been established. Mathematical dependencies have been obtained for determining the maximum angular velocity of the drive shaft of the “Turbula” type rolling machine with an additional movable slider link, which will correspond to the formation of the necessary mode of movement of the working array. The presented results of analytical studies can be applied in the relevant design bureaus of machine-building enterprises at the stage of designing equipment with complex spatial movement of working capacities and felting technological processes.

  • DETERMINATION OF THE RELATIONSHIP BETWEEN THE CHANGE OF THE MOTION MODES OF THE WORKING ARRAY AND THE DESIGN FEATURES OF THE “TURBULA” TYPE TURNING MACHINE

    by Mark Zalyubovskyi, Igor Panasyuk, Olexandr Koshel, Kyiv National University of Technology and Design, Open International University of Human Development “Ukraine”

    Using the SolidWorks automated design system, analytical studies of the “Turbula” type rolling machine with an additional movable rocker link with a vertical axis of rotation were carried out for the possibility of determining the dependence between the change in the movement modes of the working array and the design features of this rolling machine. It is noted that the movement of the working array in the filling tanks with different types of movement can be carried out in cascade, waterfall, mixed, as well as closed modes of movement. During the implementation of each mode of movement of the working array, conditions are created for the performance of appropriate felting technological operations or mixing of loose fine-dispersed substances. It was established that the change in the modes of movement of the working array in the rolling container performing complex spatial movement depends on three factors – the large-scale standard size of the rolling machine, the angular velocity of the drive shaft and the ratio of the interaxial distance of the container to the interaxial distance of the forks, which is characterized by the coefficient λ, the relationship is established the relationship between these factors. Mathematical dependencies have been obtained to determine the maximum angular speed of the drive shaft of the “Turbula” type rolling machine with an additional movable rocker link with a vertical axis of rotation, which will correspond to the implementation of the necessary mode of movement of the working array, when it moves in a given capacity. The obtained results of analytical studies can be used in the relevant design bureaus of machine-building enterprises at the stage of designing rolling equipment with complex spatial movement of working capacities.

  • DEVELOPMENT OF A HIGH-PERFORMANCE HOLDING MACHINE WITH COMPLEX SPATIAL MOVEMENT OF TWO WORKING CAPACITIES

    by Zalyubovskyi Mark, Igor Panasyuk, Kyiv National University of Technology and Design

    A new design of the galvanizing machine is proposed, which is equipped with two working tanks that perform complex spatial movement. The structure and principle of operation of the developed design of the machine are accurately described. The developed design of the machine with two capacities that perform complex spatial movement allows to increase considerably productivity of processing of details due to the fact that there is a possibility to carry out two different thawing technological operations on one machine or to process two parties of different details at the same time. The design of the machine, during operation, allows to involve in working process, both both working capacities, and one. Equipping the machine with a special drive design with four Hook hinges allows to reproduce the required law of change of angular velocity on each driving shaft of the machine, the implementation of which will create conditions that will ensure the same intensity of the working array between opposite ends of the tank in opposite directions. process, as well as uniform dynamic loading of all moving parts. Analytical studies were performed, within which some geometrical parameters of the machine design were determined, in particular, the value of the angle α between the axes of the shafts of each Hook hinge was established, which will ensure the implementation of the required angular velocity law on the machine drive shaft. The relationship between the extreme values of the law of change of the angular velocity of the driving shafts of the machine and the magnitude of the angles in each Hook hinge is established. The obtained results of analytical research can be used in the relevant design offices of machine-building enterprises at the stage of designing galvanizing equipment with complex spatial movement of working tanks.

  • TECHNICAL AND ECONOMIC RATIONALE FOR THE USE OF TURBULA TYPE MACHINING MACHINES IN POLISHING THE SURFACE OF SMALL POLYMER POLYMERS

    by Mark Zalyubovskyi

    A method of wet polishing of polymer parts using a galvanizing machine with a complex spatial movement of the working tank type «Turbula» is proposed. According to the proposed method, the main stage of polishing the surface of the parts is carried out by abrasive ceramic bodies of complex geometric shape with the addition of fine pumice in the implementation of mixed cascade-waterfall mode of movement of the bulk working medium. This method of processing parts is considered highly productive, the processing time of parts averages 15 hours of continuous operation of the machine, which is several times faster than when processing parts in rotating drum drums or vibrating machines. The latter are characterized by low productivity of the relevant technological operations. The feasibility study of the method of wet polishing of polymer parts using a galvanizing machine with a complex spatial movement of the working capacity of the «Turbula» type for the implementation of the technological operation of polishing the surface of polyester buttons was performed analytically. The expected annual economic effect from the implementation of the developed method of wet polishing of polymer parts using a galvanizing machine with a complex spatial movement of the working capacity of the «Turbula» type, which will amount to UAH 14,059.8 per two units of equipment, is calculated. This method of processing can be used to improve the surface quality of any polymer parts with the possibility of achieving the appropriate value of the roughness of their surface. The obtained research results can be used in design bureaus of relevant enterprises for the manufacture of small polymer parts, the surface quality of which is determined by organoleptic method, as well as in design bureaus of machine-building enterprises specializing in the development of galvanizing equipment.

  • TECHNICAL AND ECONOMIC JUSTIFICATION OF THE USE OF TURBULA TYPE-EQUIPMENT EQUIPMENT IN THE PERFORMANCE OF METAL DETAILS DEPARTMENT

    by Mark Zalyubovskyi, Igor Panasyuk, Kyiv National University of Technology and Design

    The types of shredding equipment used at domestic enterprises to perform the technological operation of separating parts from foundries are analyzed. It is established that machines with rotational movement of working tanks have low productivity of performance of these technological operations. In addition, a lot of time is spent on manual labor, in particular, reloading the working array to the vibrating screen. The design of the «Turbula» type galvanizing machine with complex spatial movement of the working capacity for the technological operation of separating metal parts from the foundries is proposed. This design of the machine is realized by combining in one design of the galvanizing tank (separation of parts from the foundries) and vibrating sieve (separation of separated parts from the foundries). Operation of such a structure allows to reduce the time spent on this technological operation, in particular, by providing convenient and unobstructed unloading of machined parts without the use of manual labor to overload the working array and further achieve separation of parts from foundries. The feasibility study for the use of «Turbula» equipment with complex spatial movement of the working capacity for the implementation of the technological operation of separating the metal parts of the “zipper” lock from the foundries was performed analytically. The expected annual economic effect from the introduction of the developed «Turbula» type machine with complex spatial movement of the working capacity to perform technological operations of separation of metal parts of the lock “lightning” from the foundries will be 25’688.7 UAH per unit of equipment. The developed design of the machine can be used for any type of parts (metal or polymer), which are formed by casting. The obtained research results can be used in the relevant design offices of machine-building enterprises at the stage of designing galvanizing equipment with complex spatial movement of working tanks.