Mustafa Özdemir
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mustafa Özdemir has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Akın Odabaşı
Department of Metallurgical and Materials Engineering, Engineering Faculty, Fırat University, 23200 Elazığ, Turkey
1 shared publication - Hülya Kaftelen Odabaşı
Department of Aircraft Maintenance and Repair, School of Civil Aviation, Fırat University, 23200 Elazığ, Turkey
1 shared publication - Metin Uzun
İskenderun teknik üniversitesi havacılık ve Uzay bilimleri fakütesl
1 shared publication - Murat Baydoğan
Department of Metallurgical and Materials Engineering, Istanbul Technical University, Istanbul 34469, Türkiye
1 shared publication - Sezer Çoban
Iskenderun Technical University
1 shared publication - Çağrı Vakkas Yıldırım
Erciyes Universitesi
1 shared publication
Latest Publications
- 5 September 2022
- Published by Wiley in Polymer Composites
- Vol. 44 (1) , 121-135
A study on graphene reinforced carbon fiber epoxy composites: Investigation of electrical, flexural, and dynamic mechanical properties
In this study, graphene nanoplatelets (GNPs) added to epoxy matrix composite reinforced by aeronautical grade carbon fibers (CFs) were fabricated by the vacuum infusion method, and the effect of different GNPs contents (0.05, 0.25, and 1.25 wt%) on electrical conductivity, flexural properties, and dynamic mechanical properties were investigated. The results revealed an 8‐ and 73‐times improvement in conductivity values across the thickness with the addition of 0.05 and 0.25 wt% GNPs, respectively, compared to the neat composite. Flexural test results showed that with the addition of 0.05 GNP, only 6% increase in flexural strength was obtained, while with the addition of 0.25 wt% GNP flexural strength remained almost the same as for the neat composite. On the contrary, the addition of GNPs (1.25% by weight) causes a reduction in the flexural strength with respect to the neat composite. This was confirmed by the fractured surfaces examined by scanning electron microscope which reveals that considerable amount of fiber‐matrix debonding was observed with 1.25 GNPs loading. Dynamic mechanical analysis (DMA) revealed that the storage modulus of the neat composite increased by 12.6% with the addition of only a small amount of GNP (0.05% wt) compared to the neat composite. Composite with 1.25 GNP shows upward bending, affecting the shape of the cole–cole plot obtained from DMA results, indicating inappropriate interactions of GNPs in both the matrix and CF in the composite.
- 5 September 2022
- Published by Wiley in Polymer Composites
- Vol. 44 (1) , 121-135
A study on graphene reinforced carbon fiber epoxy composites: Investigation of electrical, flexural, and dynamic mechanical properties
In this study, graphene nanoplatelets (GNPs) added to epoxy matrix composite reinforced by aeronautical grade carbon fibers (CFs) were fabricated by the vacuum infusion method, and the effect of different GNPs contents (0.05, 0.25, and 1.25 wt%) on electrical conductivity, flexural properties, and dynamic mechanical properties were investigated. The results revealed an 8‐ and 73‐times improvement in conductivity values across the thickness with the addition of 0.05 and 0.25 wt% GNPs, respectively, compared to the neat composite. Flexural test results showed that with the addition of 0.05 GNP, only 6% increase in flexural strength was obtained, while with the addition of 0.25 wt% GNP flexural strength remained almost the same as for the neat composite. On the contrary, the addition of GNPs (1.25% by weight) causes a reduction in the flexural strength with respect to the neat composite. This was confirmed by the fractured surfaces examined by scanning electron microscope which reveals that considerable amount of fiber‐matrix debonding was observed with 1.25 GNPs loading. Dynamic mechanical analysis (DMA) revealed that the storage modulus of the neat composite increased by 12.6% with the addition of only a small amount of GNP (0.05% wt) compared to the neat composite. Composite with 1.25 GNP shows upward bending, affecting the shape of the cole–cole plot obtained from DMA results, indicating inappropriate interactions of GNPs in both the matrix and CF in the composite.
- Open Access
- 23 March 2022
- Published by Journal of Aviation in Journal of Aviation
- Vol. 6 (1) , 12-25
A Novel Biomimetic Wing Design and Optimizing Aerodynamic Performance
In this article, numerical and experimental analyzes were made by adding winglet and endless blade to the tip of the airfoil to improve the wind turbine blade performance. Similarly, the change in performance was investigated by making notches at different sizes and distances on the trailing edge of the wing structure, inspired by the creatures in nature. First of all, the designed wing structures were analyzed by numerical analysis as a fixed wing, and the lift and drag forces were examined and the aerodynamic performance parameters were examined. Then, the winglet, endless wing and trailing edge notch were mounted to the wing structure cast from a 3D printer, and the energy parameters produced by each design in the wind tunnel were examined. In curved wings, the stress values produced depending on the size of the endless wing structure added to the wing tip have changed and up to 15% aerodynamic performance improvement has been observed in the designed wing structure. In addition, the design was experimentally examined on conventional fixed blades, and up to 6% improvement was observed on fixed blades.
- 23 March 2022
- Published by Journal of Aviation in Journal of Aviation
- Vol. 6 (1) , 12-25
Open AccessA Novel Biomimetic Wing Design and Optimizing Aerodynamic Performance
In this article, numerical and experimental analyzes were made by adding winglet and endless blade to the tip of the airfoil to improve the wind turbine blade performance. Similarly, the change in performance was investigated by making notches at different sizes and distances on the trailing edge of the wing structure, inspired by the creatures in nature. First of all, the designed wing structures were analyzed by numerical analysis as a fixed wing, and the lift and drag forces were examined and the aerodynamic performance parameters were examined. Then, the winglet, endless wing and trailing edge notch were mounted to the wing structure cast from a 3D printer, and the energy parameters produced by each design in the wind tunnel were examined. In curved wings, the stress values produced depending on the size of the endless wing structure added to the wing tip have changed and up to 15% aerodynamic performance improvement has been observed in the designed wing structure. In addition, the design was experimentally examined on conventional fixed blades, and up to 6% improvement was observed on fixed blades.