MBMurat Baydoğan

Murat Baydoğan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Murat Baydoğan has a total of 77 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Micro-Arc Oxidation-Derived Ceramic Coatings on a Biodegradable Zn–1Cu–0.2Mn Alloy:Microstructure, Corrosion Behavior, and Cytocompatibility

    by Ferda Mindivan, Murat Baydogan, Hakan Yilmazer, Sercan Basit, Faiz Muhaffel

    Zinc-based metals are increasingly being explored for use in biodegradable biomedical devices, primarily due to their relatively predictable corrosion rate and suitable biological compatibility compared with magnesium- and iron-derived alternatives. However, their surface corrosion still requires control for biomedical use. Here, MAO coatings were produced on Zn, Zn–1Cu, and Zn–1Cu–0.2Mn at 300, 325, and 350 V in an alkaline sodium-phosphate electrolyte. Voltage-dependent changes in surface morphology, roughness, coating thickness, phase constitution, elemental composition, electrochemical response, immersion degradation, and cell viability were evaluated. X-ray diffraction (XRD) revealed the formation of ZnO and Zn₃(PO₄)₂ phases in addition to the Zn substrate, confirming the incorporation of phosphate species from the electrolyte into the MAO coatings. Increasing the applied voltage generally increased the surface roughness and coating thickness promoted the development of a microporous surface morphology. Energy-dispersive X-ray spectroscopy (EDS) confirmed the incorporation of phosphorus into the coatings and showed an increase in oxygen content with a corresponding decrease in zinc content across the coating cross-section. The Zn–1Cu–0.2Mn coating produced at 350 V exhibited a relatively compact cross-sectional structure without visible peeling or cracking, indicating good coating/substrate integrity. Electrochemical and immersion corrosion tests demonstrated that the Zn–1Cu–0.2Mn coating produced at 350 V provided the highest overall corrosion resistance among the investigated conditions. Furthermore, the 350 V MAO-treated Zn and Zn–1Cu–0.2Mn samples exhibited cell viabilities well above the stated acceptance threshold after 48 h, indicating favorable cytocompatibility. Overall, the Zn–1Cu–0.2Mn alloy coated at 350 V demonstrated the most favorable combination of ceramic-coating characteristics, corrosion resistance, and cytocompatibility, highlighting the potential of phosphate-containing MAO coatings for controlling the surface degradation behavior of biodegradable Zn alloys for biomedical applications.

  • Open Access

    Pack Aluminizing by Induction Heating: Application to Inconel 718 Produced by Cold Spray Additive Manufacturing

    by Aptullah Karakaş, Erdem Balci, Murat Baydogan

    This study investigates the formation of aluminide coatings on Inconel 718 (IN718) superalloy produced by Cold Spray Additive Manufacturing (CSAM) using Pack Induction Aluminizing (PIA) process. The advantage of the proposed method is that the aluminizing time, which takes several hours in conventional pack aluminizing performed in furnace, can be reduced to a few tens of minutes. The microstructure, phase evolution, and tribological performance of the resulting coating were also characterized in the study. The results showed that increasing the processing time from 5 min to 10 min increased the coating thickness from approximately 10 µm to 19 µm, resulting in the formation of a double-layered aluminide coating. XRD and EDS analyses determined that the main components of the coating were aluminum-rich intermetallic compounds with an outer layer of Ni(Fe,Cr)Al3 and an inner layer of Ni2(Fe,Cr)Al3, characteristic of a high-activity aluminizing process. The PIA process significantly improved the tribological properties of the IN718 substrate. Specifically, friction coefficient slightly decreased, wear resistance increased, and wear track depth decreased by approximately 80% compared to the uncoated alloy. These findings demonstrate that the PIA method is a highly effective and rapid technique for producing protective, high-performance aluminide coatings on IN718 superalloy fabricated by cold spray additive manufacturing.


  • Open Access

    Induction assisted hot-dip and slurry aluminizing of Inconel 718

    by Aptullah Karakaş, Erdem Balcı, Murat Baydoğan

    This study compares the effect of very fast induction heating for two competitive and cost effective aluminizing process, namely, hot dip aluminizing (HDA) and slurry aluminizing (SA) of Inconel 718 superalloy. Each process produced well adhered coating layers, which comprise two or more layers. Morphological, structural and chemical characterizations of each layer were extensively studied, and formation mechanisms of the coatings were discussed in comparison to each other. The HDA process performed in a molten Al-11 wt. Si bath at 700 °C formed a 120 μm coating layer, mostly comprising of NiAl 3 . The induction heating for 20 s at 1000 °C increased the coating thickness more than two times (250 μm), transformed the aluminides to Ni 2 Al 3 , made the elemental distribution more uniform within the coatings, and also formed CrSi 2 precipitates, which might be beneficial for an improved oxidation resistance. In the SA process, the induction heating forms a coating of 43 μm in thickness, which is more uniform than the HDA coatings, and also comprises of two layers having Ni 2 Al 3 and NiAl type aluminides. EBSD examination revealed that the SA coating has a uniform grain size and random grain orientation, which are promising for improved oxidation resistance. Evaluation of the results in comparison to each other provided a better understanding of the effect of induction heating on different aluminizing processes. For example, a coating uniformity similar to that of the SA coating can be achieved only after the application of the induction heating in the HDA coatings. Also, the SA process assisted with the induction heating can be applied to various substrates without subjected them to a high temperature for a long time, and would be a promising method for partial and complete aluminizing of Ni-based substrates.

  • Unveiling the creep mechanisms of rare earth element yttrium added and SPS consolidated CoCrFeNi high entropy alloys

    by Mustafa Tekin, Hasan Kotan, Murat Baydoğan, Mertcan Kaba, Erdem Balcı, Kübra Gürcan Bayrak, Erhan Ayas

    As high entropy alloys (HEAs) continue to be increasingly studied for next-generation structural materials, gaining a comprehensive understanding of their mechanical properties, including their creep behaviors, remains essential. In this work, rare earth element yttrium (Y) added CoCrFeNi HEAs are produced by mechanical alloying, followed by consolidation via spark plasma sintering (SPS) with ultrafine grain sizes. The microstructures after SPS consolidation are examined using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The creep properties, including creep displacement, creep strain rate, creep stress, and stress exponent, are evaluated using a nanoindentation test with a Berkovich tip indenter. The results reveal that the average grain size of CoCrFeNi HEA is determined to be 385 ± 65 nm after SPS consolidation, which reduces to 190 ± 30 nm and 155 ± 55 nm with 1 and 4 at.% Y additions, respectively. Accordingly, HEA with the addition of 4 at.% Y exhibits increased hardness, attributed to the presence of additional Y-based oxides and the reduced grain size in its microstructure. Furthermore, the creep mechanisms for the investigated CoCrFeNi HEAs are primarily dominated by dislocation–precipitation interaction based on the calculated stress exponent values.


  • Open Access

    Formation of In Situ Al/TiAl3 Coatings on Electron Beam Melted (EBM) Ti-6Al-4V Alloy by Cold Spray and Induction Heating

    by Erdem Balcı, Aptullah Karakaş, Burak Bayram, Mertcan Kaba, Faiz Muhaffel, Pınar Korkmaz Tilki, Evren Tan, Murat Baydoğan

    In this study, the formation of fast, hard, well-adhered and scratch-resistant in-situ composite coatings on electron beam melted (EBM) Ti-6Al-4V alloy were proposed by successive applications of cold spray (CS) and induction heat treatment techniques. The total treatment time to achieve such properties was around only 5 min. In this context, pure aluminum (Al) was first coated by CS technique on EBM Ti-6Al-4V alloy, and the coated samples were heat treated by induction heating method for different times (10 and 20 s). The coating layer that bonded well to the substrate material was obtained using the CS technique. After the induction heating, TiAl3 intermetallics were formed in a sawtooth-like morphology as an interfacial layer at the substrate-coating interface. Similar to the interface, fiber and plate-like TiAl3 compounds were found within the CS’ed coating layer. As the induction heating time increased to 20 s, the thickness of the interfacial layer and the fraction of intermetallics in the coating layer correspondingly increased. The highest hardness and scratch resistance were obtained in the 20 s induction-heated sample. Finally, this study demonstrates that the cold spray followed by induction heating is a rapid technique to obtain hard, well-adhered and scratch-resistant composite coatings in-situ on EBM Ti-6Al-4V alloy.


  • Effect of carbon nanotube incorporation on the photocatalytic activity of TiO2 nanotubes

    by Mert Altay, Murat Baydoğan

    Arrays of titanium dioxide (TiO2) nanotubes were prepared on commercially pure titanium (Ti) foils by anodic oxidation in a 0.5 M hydrofluoric acid (HF)-based electrolyte with multiwalled carbon nanotubes (MWCNTs) up to 0.035 g/l. The samples were annealed at 450°C for 1 h after anodic oxidation to form a crystalline anatase structure. The effect of MWCNT addition on the morphology and photocatalytic activity of the nanostructures was characterized by scanning electron microscopy, Raman spectroscopy, ultraviolet–visible diffuse reflectance spectroscopy, photoluminescence spectroscopy and methylene blue degradation tests. The results showed that MWCNTs were successfully incorporated into the titanium dioxide nanotube structure and significantly affected its photocatalytic activity. The best photocatalytic performance was achieved with the use of 0.025 g/l MWCNTs in the electrolyte composition. However, when the MWCNT content in the electrolyte increased, the electron–hole recombination rate and photon absorption ability of the structure deteriorated, resulting in a decreased photocatalytic activity.


  • Open Access

    Intraoperative lateral wall breach simulation in the cadaveric spine and the impact of thread designs of screws on pullout strength in the osteoporotic thoracic vertebrae: A biomechanical study in human cadavers

    by Ozcan Kaya, Okan Ozkunt, Mustafa Sungur, Mehmet Semih Cakir, Murat Baydogan, Kerim Sariyilmaz

    Objective: This study aimed (1) to simulate pedicle screw pullout after intraoperative external wall perforation and (2) to assess restoration strength with different thread designs in the pedicle screw instrumentation for osteoporotic thoracic vertebrae. Methods: Twenty fresh-frozen human cadaveric thoracic vertebra bodies were prepared and divided into 4 groups: group 1, 5.5 mm × 45 mm polyaxial single thread pedicle screws (PASTS); group 2, after wall injury 5.5 mm × 45 mm PASTS; group 3, 6.5 mm × 45 mm PASTS after wall injury; and group 4: 6.5 mm × 45 mm polyaxial mixed-threaded screws after wall injury. While group 1 was the control group, groups 2, 3, and 4 were used as study groups after the lateral wall breach. All prepared screw units were placed on a universal pullout measurement testing device. Results: The mean bone mineral density for 20 thoracic vertebrae was 0.57 ± 0.12 g/cm2 (range 0.53-0.6 g/cm2 ). The mean pullout strength was 474.90 Newtons (N) for group 1, 412.85 N for group 2, 475.4 N for group 3, and 630.74N for group 4. The lateral wall breach caused a 14.1 % decrease in average pullout strength compared with the initial screw pullout. Mixed (double)-threaded screws increased pullout strength compared to 6.5 mm screws (P=.036) Conclusion: Using a 1 mm thicker polyaxial pedicle screw or mixed (double)-threaded pedicle screw seems to increase pullout strength; however, this was statistically significant only for group 4. In the thoracic spine, the redirection possibility of the pedicle screw is limited, and augmentation with cement will not be appropriate due to the risk of wall injury-related leakage. Therefore, care should be taken to avoid violating the lateral cortex by using appropriate pedicle entry points and trajectories. Cite this article as: Kaya O, Ozkunt O, Sungur M, Cakir MS, Baydogan M, Sariyilmaz K. Intraoperative lateral wall breach simulation in the cadaveric spine and the impact of thread designs of screws on pullout strength in the osteoporotic thoracic vertebrae: A biomechanical study in human cadavers. Acta Orthop Traumatol Turc., 2024;58(1):57-61.


  • Improved creep resistance of AZ91 magnesium alloy after the micro arc oxidation process

    by Ekin Selvi, Faiz Muhaffel, Halil İbRahim Filiz, Ali Serdar Vanlı, Murat Baydoğan