SCSittichai Charonerat

Sittichai Charonerat

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sittichai Charonerat has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Multi-objective optimization of two-point incremental forming parameters for Ti-6Al-4V using taguchi approach

    by Sittichai Charonerat, Keaittipong Onbut, Suriya Prasomthong, Yodprem Pookamnerd, Panuwat Thosa

    This study explores the optimization of essential process parameters in two-point incremental forming (TPIF) of Ti-6Al-4V titanium alloy using the Taguchi design method, in conjunction with signal-to-noise (S/N) ratio analysis and ANOVA, to enhance formability and surface characteristics. As the need for lightweight, high-performance, and customizable titanium components continues to grow in the biomedical and aerospace sectors, TPIF has emerged as a promising manufacturing method, offering high flexibility, cost efficiency, and minimal tooling requirements compared to traditional forming techniques. The study focuses on two critical response variables: forming depth and surface hardness. An L9 orthogonal array was implemented to evaluate the influence of three key parameters: step down, tool diameter, and contour path width. Experimental results indicated that tool diameter most significantly affected surface hardness, while step down was the dominant factor influencing forming depth. The optimal combination 0.3 mm step down, 10 mm tool diameter, and 6 mm contour path width produced a maximum forming depth of 8.35 mm and a surface hardness of 357 HV. The findings demonstrate that statistical design of experiments can successfully guide parameter selection to improve product quality, reduce material thinning, and minimize surface defects. Moreover, the integrated method ensures consistency, repeatability, and sustainable use of resources, making TPIF highly suitable for low-volume, high-precision applications such as patient-specific cranial implants and aerospace structural brackets. The study provides valuable insights for researchers and manufacturers aiming to advance incremental sheet forming technologies for next-generation materials

  • Open Access

    Development of mechanical property prediction model and optimization for dissimilar aluminum alloy joints with the friction stir welding (FSW) process

    by Yodprem Pookamnerd, Panuwat Thosa, Sittichai Charonerat, Suriya Prasomthong

    Friction stir welding (FSW) is a solid-state joining process used to weld dissimilar aluminum alloys with varying material properties and compositions. Unlike traditional welding methods, FSW does not involve melting the materials being welded but instead uses a rotating tool to heat and stir the materials until they are in a plastic state. The process results in a welded joint with high strength, excellent ductility, and minimal distortion, making it a popular choice in various industries, including aerospace, automotive, and marine. AA6061-T6 (Mg-Si) and AA7075 (Al-Zn-Mg-Cu) aluminum alloys are one of the most popular grades of aluminum alloys used in current manufacturing industries, such as aerospace and automotive, joined by the Friction Stir Welding Process (FSW) technique. Taguchi orthogonal array (L9) experimental design was applied to reduce the number of insignificant factors in the process. First, the study determines three welding factors: rotation speed, travel speed, and pin eccentricity. Investigations found that travel speeds significantly on tensile strength (Ts) and elongation ( %El), but the rotational speed and tool eccentricity did not affect Ts and %El. Furthermore, considering the fabricated parameters on the hardness (HV) of the joint, it was found that all factors unaffected the HV of the joint zone at a 95 % confidence level. Next, examine the microstructure; Mg2Al3 and Al2O3 intermetallic compounds were found in the weld. Therefore, investigating the crystallite size found that welding significantly affects the crystallite size. Finally, consider the fracture surface, experimental condition A2B1C2 (optimal parameter), which is the parameter with the highest tensile strength having dimple fracture characteristics. On the other hand, the welding condition A1B3C3, the parameter with the lowest tensile strength, Small and fine dimple fracture with cleavage fracture. Because the material is highly ductile and can undergo large deformations before it is damaged. On the other hand, materials with low tensile strength exhibiting cleavage fracture indicate that the materials are brittle and can break easily under stress