Yang Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Yang Liu has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Wei Jiang
4 shared publicationsZhiyuan Wang
4 shared publicationsFengyuan Bao
3 shared publicationsLicun Zhao
3 shared publications- Chenghao Zhang2 shared publications
Chun Li
2 shared publications
Latest Publications
- Open Access
- 12 October 2026
- Published by Elsevier in SSRN Electronic Journal
Ultrasonic-assisted low-temperature Cu–Cu bonding of bimodal particles for power electronics interconnects: effects on microstructure and joint properties
Low-temperature sintering of Cu particles has considerable potential for advanced power electronic packaging, but surface oxidation and insufficient atomic diffusion at low temperatures limit the performance of sintering joints. In this paper, an ultrasonic-assisted sintering process was proposed and optimized, and the effect of the ultrasonic process and sintering temperature on the microstructure and properties of the Cu-Cu sintered joints was investigated. Without ultrasonic assistance, the average shear strength increased from 6.12 MPa to 46.73 MPa as the sintering temperature increased from 200°C to 240 °C, which was primarily attributable to the temperature promoting atomic diffusion. The joint performance showed a trend of increasing first and then decreasing with the increase of ultrasonic power and duration under the ultrasonic-assisted process at 200°C. The best performance was obtained at 600 W for 4 s, giving a shear strength of 43.35 MPa, approximately 7.1 times higher than that without ultrasonic assistance at 200°C, approaching the shear strength of the sintered joint without ultrasonic-assisted sintering at 240℃. However, excessively high ultrasonic power and duration could damage the sintered layer, cause micro-cracks, and reduce performance. Microstructural analysis indicates that moderate ultrasonic treatment could promote surface-oxide disruption, particle rearrangement, and plastic deformation, thereby facilitating atomic diffusion and sintering-neck growth at low temperatures, and transforming the fracture path from interface separation to internal cohesive fracture. This study proposed an ultrasonic-assisted process for copper particle low-temperature sintering and elucidated its strengthening mechanism, providing a basis for Cu-Cu bonding in low thermal budget power devices.
- 12 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessUltrasonic-assisted low-temperature Cu–Cu bonding of bimodal particles for power electronics interconnects: effects on microstructure and joint properties
Low-temperature sintering of Cu particles has considerable potential for advanced power electronic packaging, but surface oxidation and insufficient atomic diffusion at low temperatures limit the performance of sintering joints. In this paper, an ultrasonic-assisted sintering process was proposed and optimized, and the effect of the ultrasonic process and sintering temperature on the microstructure and properties of the Cu-Cu sintered joints was investigated. Without ultrasonic assistance, the average shear strength increased from 6.12 MPa to 46.73 MPa as the sintering temperature increased from 200°C to 240 °C, which was primarily attributable to the temperature promoting atomic diffusion. The joint performance showed a trend of increasing first and then decreasing with the increase of ultrasonic power and duration under the ultrasonic-assisted process at 200°C. The best performance was obtained at 600 W for 4 s, giving a shear strength of 43.35 MPa, approximately 7.1 times higher than that without ultrasonic assistance at 200°C, approaching the shear strength of the sintered joint without ultrasonic-assisted sintering at 240℃. However, excessively high ultrasonic power and duration could damage the sintered layer, cause micro-cracks, and reduce performance. Microstructural analysis indicates that moderate ultrasonic treatment could promote surface-oxide disruption, particle rearrangement, and plastic deformation, thereby facilitating atomic diffusion and sintering-neck growth at low temperatures, and transforming the fracture path from interface separation to internal cohesive fracture. This study proposed an ultrasonic-assisted process for copper particle low-temperature sintering and elucidated its strengthening mechanism, providing a basis for Cu-Cu bonding in low thermal budget power devices.
- 11 August 2026
- Published by Emerald Publishing in Soldering & Surface Mount Technology
- p. 1-11
Reliability analysis of large area sintered Cu interconnects based on simulation and thermal shock test
Purpose: The purpose of this study is to assess the thermomechanical reliability of large-area sintered Cu interconnects for automotive power modules under actual operating conditions and to determine the optimal sintering layer thickness using finite element simulation and experimental validation. The escalating demand for high-performance electronic packaging has underscored the significance of sintered Cu interconnects, renowned for their superior electrical and thermal conductivities. Recent attempts to apply large-area sintered Cu between the module and heatsink have shown that such interconnections can achieve lower thermal resistance and higher bonding strength. However, the reliability of these interconnects under thermal cycling conditions remains a critical concern. Design/methodology/approach: This study used a combined approach of finite element (FE) simulation and experimental validation to assess the reliability of sintered Cu interconnects under actual operating conditions. First, FE simulation is conducted under irregular thermal flux to simulate the actual working conditions of the module. Based on the stress–strain results, the optimal sintering layer thickness is determined, while also considering printing yield and economic feasibility. Subsequently, shear strength tests were conducted on shear specimen model and thermal shock testing (TST) along with C SAM (scanning acoustic microscopy) analysis were performed on TST specimen. Findings: This study evaluates the thermomechanical reliability of large-area sintered copper interconnects for automotive power modules. Combining FE simulations and experiments, the optimal sintering layer thickness was determined to be 100 µm. The overall structure exhibited high shear strength (>25 MPa) and withstood 1,000 thermal shock cycles (−40 °C to 125 °C) with a delamination rate of only 1.575% and negligible crack propagation. Its excellent reliability for next-generation electronics was confirmed. Originality/value: This study provides the reliability assessment of large-area sintered Cu interconnects specifically for automotive power modules, bridging the gap between process optimization and durability in actual working conditions. The identified optimal thickness of 100 µm sintered layer offers a critical design rule, balancing thermomechanical performance with manufacturability. The combined simulation-experimental approach quantitatively validates that this interconnect solution can withstand stringent automotive thermal cycling with exceptional durability (<2% delamination after 1,000 cycles), offering a credible high-performance alternative to traditional solders or sintered silver.
- 11 August 2026
- Published by Emerald Publishing in Soldering & Surface Mount Technology
- p. 1-11
Reliability analysis of large area sintered Cu interconnects based on simulation and thermal shock test
Purpose: The purpose of this study is to assess the thermomechanical reliability of large-area sintered Cu interconnects for automotive power modules under actual operating conditions and to determine the optimal sintering layer thickness using finite element simulation and experimental validation. The escalating demand for high-performance electronic packaging has underscored the significance of sintered Cu interconnects, renowned for their superior electrical and thermal conductivities. Recent attempts to apply large-area sintered Cu between the module and heatsink have shown that such interconnections can achieve lower thermal resistance and higher bonding strength. However, the reliability of these interconnects under thermal cycling conditions remains a critical concern. Design/methodology/approach: This study used a combined approach of finite element (FE) simulation and experimental validation to assess the reliability of sintered Cu interconnects under actual operating conditions. First, FE simulation is conducted under irregular thermal flux to simulate the actual working conditions of the module. Based on the stress–strain results, the optimal sintering layer thickness is determined, while also considering printing yield and economic feasibility. Subsequently, shear strength tests were conducted on shear specimen model and thermal shock testing (TST) along with C SAM (scanning acoustic microscopy) analysis were performed on TST specimen. Findings: This study evaluates the thermomechanical reliability of large-area sintered copper interconnects for automotive power modules. Combining FE simulations and experiments, the optimal sintering layer thickness was determined to be 100 µm. The overall structure exhibited high shear strength (>25 MPa) and withstood 1,000 thermal shock cycles (−40 °C to 125 °C) with a delamination rate of only 1.575% and negligible crack propagation. Its excellent reliability for next-generation electronics was confirmed. Originality/value: This study provides the reliability assessment of large-area sintered Cu interconnects specifically for automotive power modules, bridging the gap between process optimization and durability in actual working conditions. The identified optimal thickness of 100 µm sintered layer offers a critical design rule, balancing thermomechanical performance with manufacturability. The combined simulation-experimental approach quantitatively validates that this interconnect solution can withstand stringent automotive thermal cycling with exceptional durability (<2% delamination after 1,000 cycles), offering a credible high-performance alternative to traditional solders or sintered silver.
- 18 July 2026
- Published by Elsevier in Applied Surface Science
- Vol. 749
In situ nanostructured Cu surfaces for low-temperature joining: interfacial behavior and bonding mechanism
- 18 July 2026
- Published by Elsevier in Applied Surface Science
- Vol. 749
In situ nanostructured Cu surfaces for low-temperature joining: interfacial behavior and bonding mechanism
- Open Access
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Research on the Controllable Fabrication of Amorphous/Nanocrystalline Multilayer Film Modulation Structures and the Tribological Damage Mechanism
In this study, utilising magnetron sputtering technology and by precisely controlling the structural parameters of amorphous/nanocrystalline multilayer films, we successfully fabricated a composite film system with varying modulation ratios and systematically elucidated the coupling mechanism between the film’s microstructure and tribological properties. The residual stress state of the film and the distribution characteristics of the amorphous and nanocrystalline phases have a decisive influence on its friction and wear behaviour. The amorphous phase, owing to its excellent toughness and stress buffering capacity, is capable of effectively suppressing the propagation of microcracks under alternating loads; the nanocrystalline phase, acting as a hard reinforcing phase, provides the film with superior load-bearing support through grain boundary strengthening and dispersion strengthening mechanisms; whilst the high-density, well-defined heterogeneous interfaces facilitate the effective dissipation of strain energy during friction via interfacial shear slippage and stress redistribution, thereby delaying the film failure process. Tribological performance tests indicate that the wear rate of the optimised film was significantly reduced by 28.7% and 22.1% compared to films (1#) and (3#), respectively, demonstrating excellent friction stability. By establishing a design strategy of ’stress regulation–structural optimisation–performance synergy’, this study provides a new theoretical basis and technical approach for the development of high-performance wear-resistant films.
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessResearch on the Controllable Fabrication of Amorphous/Nanocrystalline Multilayer Film Modulation Structures and the Tribological Damage Mechanism
In this study, utilising magnetron sputtering technology and by precisely controlling the structural parameters of amorphous/nanocrystalline multilayer films, we successfully fabricated a composite film system with varying modulation ratios and systematically elucidated the coupling mechanism between the film’s microstructure and tribological properties. The residual stress state of the film and the distribution characteristics of the amorphous and nanocrystalline phases have a decisive influence on its friction and wear behaviour. The amorphous phase, owing to its excellent toughness and stress buffering capacity, is capable of effectively suppressing the propagation of microcracks under alternating loads; the nanocrystalline phase, acting as a hard reinforcing phase, provides the film with superior load-bearing support through grain boundary strengthening and dispersion strengthening mechanisms; whilst the high-density, well-defined heterogeneous interfaces facilitate the effective dissipation of strain energy during friction via interfacial shear slippage and stress redistribution, thereby delaying the film failure process. Tribological performance tests indicate that the wear rate of the optimised film was significantly reduced by 28.7% and 22.1% compared to films (1#) and (3#), respectively, demonstrating excellent friction stability. By establishing a design strategy of ’stress regulation–structural optimisation–performance synergy’, this study provides a new theoretical basis and technical approach for the development of high-performance wear-resistant films.
- 25 May 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1071
The evolution of structural and magnetic properties in soft magnetic alloy films induced by Si doping
- 25 May 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1071
The evolution of structural and magnetic properties in soft magnetic alloy films induced by Si doping
- 25 July 2025
- Published by Elsevier in Corrosion Science
- Vol. 256
Research on the amorphous–nanocrystalline heterointerfaces for optimized CoCrFeNiAl protective film growth
- 25 July 2025
- Published by Elsevier in Corrosion Science
- Vol. 256
Research on the amorphous–nanocrystalline heterointerfaces for optimized CoCrFeNiAl protective film growth
- 1 July 2025
- Published by Elsevier in Optics & Laser Technology
- Vol. 192
A case study: dynamic behavior of a typical Micro-LED chips during laser induced forward transfer process
- 1 July 2025
- Published by Elsevier in Optics & Laser Technology
- Vol. 192
A case study: dynamic behavior of a typical Micro-LED chips during laser induced forward transfer process