Yu Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yu Chen has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Chao Chen
Center For Precision Cancer Medicine Med‐X Institute The First Affiliated Hospital of Xi'an Jiaotong University Xi'an China
1 shared publication - Chunyu Liu
MOE Key Laboratory of Rare Pediatric Diseases & Hunan Key Laboratory of Medical Genetics, School of Life Sciences, and Department of Psychiatry, The Second Xiangya Hospital, Central South University, Changsha, China
1 shared publication - Cuihua Xia
Central South University
1 shared publication Fei Wang
School of Resource and Safety Engineering
1 shared publication- Lei Li
Institute of Mass Spectrometry and Atmospheric Environment, Jinan University, Guangzhou 510632, China
1 shared publication Longfei Tang
Central South University
1 shared publication
Latest Publications
- 1 October 2021
- Published by Elsevier in European Neuropsychopharmacology
- Vol. 51, e140-e141
TU83. COMPARING GENE EXPRESSION CHANGES IN BLOOD AND BRAIN OF SCHIZOPHRENIA
- 1 October 2021
- Published by Elsevier in European Neuropsychopharmacology
- Vol. 51, e140-e141
TU83. COMPARING GENE EXPRESSION CHANGES IN BLOOD AND BRAIN OF SCHIZOPHRENIA
- 1 July 2021
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 142, 106586
The online detection of halogenated hydrocarbon in the atmosphere
- 1 July 2021
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 142, 106586
The online detection of halogenated hydrocarbon in the atmosphere
- Open Access
- 1 January 2018
- Published by Wiley in Advances in Civil Engineering
- Vol. 2018 (1)
An Experimental Study on Mechanical Behavior of Parallel Joint Specimens under Compression Shear
In order to investigate the influence of the joint on the failure mode, peak shear strength, and shear stress‐strain curve of rock mass, the compression shear test loading on the parallel jointed specimens was carried out, and the acoustic emission system was used to monitor the loading process. The joint spacing and joint overlap were varied to alter the relative positions of parallel joints in geometry. Under compression‐shear loading, the failure mode of the joint specimen can be classified into four types: coplanar shear failure, shear failure along the joint plane, shear failure along the shear stress plane, and similar integrity shear failure. The joint dip angle has a decisive effect on the failure mode of the specimen. The joint overlap affects the crack development of the specimen but does not change the failure mode of the specimen. The joint spacing can change the failure mode of the specimen. The shear strength of the specimen firstly increases and then decreases with the increase of the dip angle and reaches the maximum at 45°. The shear strength decreases with the increase of the joint overlap and increases with the increase of the joint spacing. The shear stress‐displacement curves of different joint inclination samples have differences which mainly reflect in the postrupture stage. From monitoring results of the AE system, the variation regular of the AE count corresponds to the failure mode, and the peak value of the AE count decreases with the increase of joint overlap and increases with the increase of joint spacing.
- 1 January 2018
- Published by Wiley in Advances in Civil Engineering
- Vol. 2018 (1)
Open AccessAn Experimental Study on Mechanical Behavior of Parallel Joint Specimens under Compression Shear
In order to investigate the influence of the joint on the failure mode, peak shear strength, and shear stress‐strain curve of rock mass, the compression shear test loading on the parallel jointed specimens was carried out, and the acoustic emission system was used to monitor the loading process. The joint spacing and joint overlap were varied to alter the relative positions of parallel joints in geometry. Under compression‐shear loading, the failure mode of the joint specimen can be classified into four types: coplanar shear failure, shear failure along the joint plane, shear failure along the shear stress plane, and similar integrity shear failure. The joint dip angle has a decisive effect on the failure mode of the specimen. The joint overlap affects the crack development of the specimen but does not change the failure mode of the specimen. The joint spacing can change the failure mode of the specimen. The shear strength of the specimen firstly increases and then decreases with the increase of the dip angle and reaches the maximum at 45°. The shear strength decreases with the increase of the joint overlap and increases with the increase of the joint spacing. The shear stress‐displacement curves of different joint inclination samples have differences which mainly reflect in the postrupture stage. From monitoring results of the AE system, the variation regular of the AE count corresponds to the failure mode, and the peak value of the AE count decreases with the increase of joint overlap and increases with the increase of joint spacing.