Yuri Nikolaevich Loginov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yuri Nikolaevich Loginov has a total of 139 co-authors. Here are the top co-authors by number of shared publications:
- Georgy V. Shimov
Ural Federal University
7 shared publications - Nikolay A. Babailov
Institute of Engineering Science, Ural Branch of the Russian Academy of Sciences
7 shared publications S. L. Demakov
Ural Federal University (UrFU)
6 shared publicationsA. G. Illarionov
Yeltsin Ural Federal University
5 shared publicationsA. Yu. Postylyakov
Ural Federal University, 620002, Yekaterinburg, Russia
4 shared publicationsL. I. Polyansky
4 shared publications
Latest Publications
- 3 November 2026
- Published by Springer Nature in Metallurgist
- p. 1-7
Extrusion of aluminum alloy rods following a pre-straining stage
- 3 November 2026
- Published by Springer Nature in Metallurgist
- p. 1-7
Extrusion of aluminum alloy rods following a pre-straining stage
- 1 May 2026
- Published by Springer Nature in Metallurgist
- Vol. 70 (1) , 75-82
Visualization of actual shape change and digitization of aluminum alloy slab rolling
- 1 May 2026
- Published by Springer Nature in Metallurgist
- Vol. 70 (1) , 75-82
Visualization of actual shape change and digitization of aluminum alloy slab rolling
- 15 July 2025
- Published by Springer Nature in Metallurgist
- Vol. 69 (4) , 480-487
Hot-extrusion of platinum-rhodium alloy tubes
- 15 July 2025
- Published by Springer Nature in Metallurgist
- Vol. 69 (4) , 480-487
Hot-extrusion of platinum-rhodium alloy tubes
- 30 May 2025
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 5,p. 58-62
Influence of hardening curve parameters of material on deformation distribution in deep drawing
The aim of the work is to evaluate the influence of the parameters of the hardening curve of the deformed material on the distribution of deformations in the deep drawing operation. It is noted that in the conditions of forging and stamping production, reference data on the strength properties of materials are often used, obtained by the method of preliminary flat rolling of samples with subsequent measurement of the conditional yield strength. In this case, the level of deformations is estimated by the relative compression index, and the same index is used to estimate the deformation in forging operations. However, to perform calculations of the change in shape in modern programs, the true deformation index is required. Formulas for recalculating the deformation indices are given. It is proposed to estimate the degree of intensity of metal work hardening by differentiating the conditional yield strength as a function of the deformation index and obtaining the derivative of the function. It is revealed that high-carbon steel 85 has a high hardening intensity index, and corrosion-resistant chromium-nickel steel has a low index. It is suggested that, based on the principle of minimum energy, the region of greatest deformation will move to the zone of smaller deformations, due to which the thinning of the workpiece during drawing will be aligned along the coordinates. Two boundary value problems of deep drawing of a hemisphere by the finite element method for the two steels mentioned above are set and solved. The previously formed hypothesis was confirmed - the results of the solution showed a decrease in the level of maximum deformation in steel with a higher value of the derivative of the conditional yield strength function. It was additionally revealed that the maximum degree of deformation can be located both on the inner side of the stamping and on the outer side, depending on the type of the hardening curve, which affects the possibility of cracks.
- 30 May 2025
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 5,p. 58-62
Influence of hardening curve parameters of material on deformation distribution in deep drawing
The aim of the work is to evaluate the influence of the parameters of the hardening curve of the deformed material on the distribution of deformations in the deep drawing operation. It is noted that in the conditions of forging and stamping production, reference data on the strength properties of materials are often used, obtained by the method of preliminary flat rolling of samples with subsequent measurement of the conditional yield strength. In this case, the level of deformations is estimated by the relative compression index, and the same index is used to estimate the deformation in forging operations. However, to perform calculations of the change in shape in modern programs, the true deformation index is required. Formulas for recalculating the deformation indices are given. It is proposed to estimate the degree of intensity of metal work hardening by differentiating the conditional yield strength as a function of the deformation index and obtaining the derivative of the function. It is revealed that high-carbon steel 85 has a high hardening intensity index, and corrosion-resistant chromium-nickel steel has a low index. It is suggested that, based on the principle of minimum energy, the region of greatest deformation will move to the zone of smaller deformations, due to which the thinning of the workpiece during drawing will be aligned along the coordinates. Two boundary value problems of deep drawing of a hemisphere by the finite element method for the two steels mentioned above are set and solved. The previously formed hypothesis was confirmed - the results of the solution showed a decrease in the level of maximum deformation in steel with a higher value of the derivative of the conditional yield strength function. It was additionally revealed that the maximum degree of deformation can be located both on the inner side of the stamping and on the outer side, depending on the type of the hardening curve, which affects the possibility of cracks.
- Open Access
- 1 February 2025
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2025 (1) , 36-43
Optimal dimensions of magnesium oxide briquettes
The paper discusses experimental studies on determining the drop strength of cylindrical magnesium oxide briquettes used in the metallurgical and refractory industries. Briquettes with a magnesium oxide content of 97% were produced by dry pressing, i.e. without a binder or moisture. Special equipment for producing cylindrical briquettes by single-action compacting in a closed mold was manufactured in the laboratory. The particle size of the material to be compacted does not exceed 1 mm. The resulting briquettes are studied with the following compaction process parameters: compaction stress ranging from 20 to 100 MPa, without heating the mixture and without lubricating the inner surface of the mold. The cylindrical briquettes were produced on a vertical hydraulic press with a nominal force of 100 kN. All the series of briquettes were produced with the same mixture compaction coefficient, which is equal to 3. These modes of compacting charge mixtures are implemented on roller briquetting presses under commercial production conditions. The study determines the following briquette properties: average density and drop strength. The average briquette density is 2.05 g/cm3. The analysis of the mechanical properties yields the optimal briquette shape in terms of strength. The results of the study make it possible to optimize the process of producing briquettes from magnesium oxide and to change the shape and size of the cells cut on the rolls of briquetting presses. The results will increase the economic efficiency of briquetting processes and the productivity of the roll briquetting process.
- 1 February 2025
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- Vol. 2025 (1) , 36-43
Open AccessOptimal dimensions of magnesium oxide briquettes
The paper discusses experimental studies on determining the drop strength of cylindrical magnesium oxide briquettes used in the metallurgical and refractory industries. Briquettes with a magnesium oxide content of 97% were produced by dry pressing, i.e. without a binder or moisture. Special equipment for producing cylindrical briquettes by single-action compacting in a closed mold was manufactured in the laboratory. The particle size of the material to be compacted does not exceed 1 mm. The resulting briquettes are studied with the following compaction process parameters: compaction stress ranging from 20 to 100 MPa, without heating the mixture and without lubricating the inner surface of the mold. The cylindrical briquettes were produced on a vertical hydraulic press with a nominal force of 100 kN. All the series of briquettes were produced with the same mixture compaction coefficient, which is equal to 3. These modes of compacting charge mixtures are implemented on roller briquetting presses under commercial production conditions. The study determines the following briquette properties: average density and drop strength. The average briquette density is 2.05 g/cm3. The analysis of the mechanical properties yields the optimal briquette shape in terms of strength. The results of the study make it possible to optimize the process of producing briquettes from magnesium oxide and to change the shape and size of the cells cut on the rolls of briquetting presses. The results will increase the economic efficiency of briquetting processes and the productivity of the roll briquetting process.
- 7 January 2025
- Published by Springer Nature in Metallurgist
- Vol. 68 (9) , 1302-1312
Experimental study of the influence of hot rolling on the structure, texture, and properties of a two-phase Ti–4.5Al–3Mo–V titanium alloy
- 7 January 2025
- Published by Springer Nature in Metallurgist
- Vol. 68 (9) , 1302-1312
Experimental study of the influence of hot rolling on the structure, texture, and properties of a two-phase Ti–4.5Al–3Mo–V titanium alloy
- Open Access
- 1 January 2025
- Published by Togliatti State University in Frontier materials & technologies
- No. 3,p. 27-37
Scheme for producing composite material based on structural aluminum alloy by the direct extrusion method
The work covers the development of a technology for producing a bimetallic rod from high-strength 7075 alloy with a cladding layer of 1100 aluminum, which is aimed at improving corrosion resistance while maintaining mechanical properties. A special feature of the proposed technology is the use of an additional front pure aluminum workpiece for the process of direct extrusion of a rod from 7075 alloy. The direct extrusion process for a composite workpiece was simulated with the DEFORM software package’s finite element method. The influence of process temperature and speed on the formation of the cladding layer was analyzed. For this purpose, four problems were formulated with varying heating modes of workpieces and tools. It was found that it is possible to produce a thin cladding layer at a heating temperature of the base 7075 alloy equal to 360 °C and a cladding layer temperature equal to 20 °C, which ensures a uniform distribution of the coating along the length of the rod without signs of delamination. Stress-strain analysis during extrusion showed that a cold additional workpiece ensures continuity for cladding coating formation. However, heating above 300 °C leads to rupture from deformation localization. The developed approach can be used to reduce the cost of products by reducing the consumption of expensive 7075 alloy while simultaneously increasing corrosion resistance due to the use of pure aluminum cladding. Prospects for the development of further research are associated with the optimization of extrusion modes for various rod sizes.
- 1 January 2025
- Published by Togliatti State University in Frontier materials & technologies
- No. 3,p. 27-37
Open AccessScheme for producing composite material based on structural aluminum alloy by the direct extrusion method
The work covers the development of a technology for producing a bimetallic rod from high-strength 7075 alloy with a cladding layer of 1100 aluminum, which is aimed at improving corrosion resistance while maintaining mechanical properties. A special feature of the proposed technology is the use of an additional front pure aluminum workpiece for the process of direct extrusion of a rod from 7075 alloy. The direct extrusion process for a composite workpiece was simulated with the DEFORM software package’s finite element method. The influence of process temperature and speed on the formation of the cladding layer was analyzed. For this purpose, four problems were formulated with varying heating modes of workpieces and tools. It was found that it is possible to produce a thin cladding layer at a heating temperature of the base 7075 alloy equal to 360 °C and a cladding layer temperature equal to 20 °C, which ensures a uniform distribution of the coating along the length of the rod without signs of delamination. Stress-strain analysis during extrusion showed that a cold additional workpiece ensures continuity for cladding coating formation. However, heating above 300 °C leads to rupture from deformation localization. The developed approach can be used to reduce the cost of products by reducing the consumption of expensive 7075 alloy while simultaneously increasing corrosion resistance due to the use of pure aluminum cladding. Prospects for the development of further research are associated with the optimization of extrusion modes for various rod sizes.
- 24 December 2024
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 22 (4)
Plastic Bending of a Round Sheet Blank of Variable Curvature
- 24 December 2024
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 22 (4)
Plastic Bending of a Round Sheet Blank of Variable Curvature
- 24 October 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (7) , 992-1000
Initial stage of titanium alloy tube billet extrusion: simulation and experiment
- 24 October 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (7) , 992-1000
Initial stage of titanium alloy tube billet extrusion: simulation and experiment
- 30 September 2024
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 22 (3)
Simulation of Plate Rolling of the Aluminum Alloy with Options of Softening Processes
- 30 September 2024
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 22 (3)
Simulation of Plate Rolling of the Aluminum Alloy with Options of Softening Processes