GSGeorgy V. Shimov

Georgy V. Shimov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Georgy V. Shimov has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Hot-extrusion of platinum-rhodium alloy tubes

    by Yu. N. Loginov, A. E. Pervukhin, G. V. Shimov, N. I. Bushueva

  • Pressing of clad rods from aluminum alloys using a front deformable washer

    by N. I. Bushueva, Yu. N. Loginov, G. V. Shimov

    The possibility of producing a bimetallic rod from an aluminum alloy by pressing has been studied. At the first stage of the study, numerical modeling was carried out in a specialized software package using the finite element method. The problem of pressing a large-size rod made of aluminum alloy 6061 was formulated using an additional bar made of a softer aluminum alloy in the processing state for direct and reverse pressing options. The features of the stress-strain state of materials during the pressing process have been studied. Using the function of tracer points, a comparison of flow rates of materials of the main and additional bars during plastic deformation was made. Graphs of the dependence of cladding layer thickness on the length of the rod`s pressed part for the options of direct and reverse pressing were constructed. Graphs of the flow rate distribution of materials of the main and additional bars for direct and reverse pressing options were also constructed. It has been established that to achieve the task of producing a bimetallic rod, it is prefera bleto use the direct pressing method. Based on the results of numerical modeling, a defective area was identified where peeling of the cladding bar metal is observed. An experimental modeling of the bimetallic rod pressing process was carried out in order to confirm the correctness of the numerical modeling results. During experimental pressing, a defect was detected on the surface of the bimetallic product, which corresponds to the numerical simulation data. Conclusions are drawn about the possible causes of the defect.The research was carried out with financial support from the Ministry of Science and Higher Education of the Russian Federation within the framework of the Development Program of the Ural Federal University named after the first President of Russia B. N. Yeltsin in accordance with the strategic academic leadership program “Priority – 2030”.


  • Aluminum alloy extrusion scheme and model with reduction of basis metal waste

    by Yu. E. Loginov, A. V. Razinkin, G. V. Shimov, N. I. Bushueva

    This paper considers the process of extrusion of aluminium alloy 6061 bars aimed at finding a way to minimize the in-process metal loss due to the use of an additional work piece (in the form of back plug) made of cheaper material. Numerical modelling of the extrusion process was carried out for three different heating modes applied to both the tooling and the work pieces. The authors analyzed the mutual flow of the ingot and plug material at the final stage of extrusion in order to determine the moment when the back end defect starts to form and how it forms. The stress-strain state for three process options was investigated. Thus, the authors looked at the colour gradient pictures showing the distribution of strain and strain rate longitudinally along the extrusion centerline. It was found that when a pre-heated additional work piece is used, the butt-end should be made larger because of the early formed back end defect. When a cold plug and a hot dummy block are used, the back end defect forms early as well, as the back plug heats up at the final process stage reaching almost the same temperatures as the main work piece. It was established that the optimum option would be not heating the back work piece or the dummy block. The modelling helped reveal that the size of the buttend in this case is smaller. The obtained modelling data can be used for conducting pilot studies aimed at reducing the size of the butt-end when producing extruded aluminium bars. This will help improve the metal utilization factor.This research was carried out as part of Project No. 22-29-00931 dated 20/12/2021 by the Russian Science Foundation.


  • Processing non-dimensional pipe sections to obtain cold-rolled strip

    by G. V. Shimov, Yu. N. Loginov, N. I. Bushueva

    The work purpose is to assess the possibility of obtaining of marketable products in the form of a thin strip from non-dimensional pipe sections. Two options for processing pipe sections into a cold strip are considered: the first option is flattening – rolling – separation, the second one is flattening – separation – rolling. The physical modeling was used in order to test the proposed schemes for the analysis, as well as process computer simulation under consideration in a finite element formulation. Computer simulation made it possible to establish deformation accumulation patterns in various areas of the strip from operation to operation and to analyze the metal destruction probability in "dangerous" zones. It is shown that the flattening stage forms large values of accumulated deformation in the future strip edges, which subsequently leads to cracking of lateral edges. In addition, accumulated metal damage in these zones leads to the need to remove them after rolling (the option 1) or immediately after flattening before rolling (the option 2). The strip obtained by both methods has a fairly uniform strain degree distribution over the cross section. Physical modeling made it possible to verify the proposed technical solutions feasibility. A strip was obtained in accordance with GOST 4986-79 with a length - 1.5 m according to both proposed options. The advantages and disadvantages of both options for processing such pipe sections are shown. Several interesting effects related to the "double strip" rolling have been established. The pipe inner surface after rolling became smooth, roughness decreased, and externally it became shiny in contrast to the outer matte surface. This effect is explained by the favorable stress state at the strip-strip boundary, which leads to strip surface smoothing. The principal possibility of introducing the considered nondimensional pipe scraps processing method to obtain marketable products without transferring the metal into the liquid phase has been established as a result of the work.The studies were carried out as part of the implementation of the project of the Russian Science Foundation (No. 22-29-00931 dated December 20/2021).


  • Open Access

    Structure and strain state of aluminum bars at the initial phase of extrusion

    by Yu. N. Loginov, A. V. Razinkin, G. V. Shimov, T. V. Maltseva, N. I. Bushueva, E. G. Dymshakova, N. A. Kalinina

    The structure of insufficiently deformed areas at the non-steady phase of extrusion was studied. The tests at Kamensk Uralsky Metallurgical Works using a 120 MN press and 800 mm dia. container, in order to extrude a 355.6 mm dia. Bar was performed. The bar material is the Al–Mg–Si AD33 aluminum alloy (GOST 4784), similar to ASTM 6061. The percentage reduction was 80 %, and the reduction ratio was 5.06. After that, the macrostructure, microstructure, and average grain size along the radius, mechanical properties at room and elevated temperatures were investigated. It was found that the extruded bar macrostructure is fine-grained, homogeneous, and dense, with no nonmetallic or intermetallic inclusions. The cross-section contained several structures. The central part is weakly deformed preserving the dendritic cell structure inherited from the casting. At the circumference, a streaked structure is formed. Its components are crushed and uniformly distributed. We measured the strength at elevated temperatures and compared the results to the data available in the literature. The tested material strength almost doubled, thus indicating its incomplete softening. The ductility was also performed. The DEFORM-2D software, in order to simulate the low reduction of extrusion was used. The metal at the circumference is exposed to a greater strain from the extrusion beginning. A step-by-step analysis indicated that at the first step, the strain is localized near the die hole. In the second step, a rigid area is formed in the vicinity of the die/container liner interface. The circumference layer of metal with a 1.75–2.00 reduction of area is formed. At the bar center, this range is 0.75–1.00 (half of the circumference value). In the third step, the circumference layer with an elevated strain has a wedge-like shape. In the fourth step, the circumference layer (with elevated strain) has an equal thickness along the extrusion axis. This indicates the steady phase. The plastic strain at the bar front end is higher at the circumference than in the center. This confirms the structural analysis results. They show that the central part of the bar may retain its cast structure, while the circumference is deformed. If the bar central part is required to have some specific properties, the bar has to undergo another manufacturing operation to increase the accumulated strain. Re-extrusion processes the areas insufficiently deformed during the first extrusion.


  • Lead Brass Bar Two-Channel Extrusion

    by Yu. N. Loginov, G. V. Shimov, A. S. Vorsin