Bert Hannon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bert Hannon has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Peter Sergeant
Ghent University
4 shared publications Luc Dupre
Electrical Energy Laboratory, Department of Electrical Machines, Metals, Mechanical Constructions and Systems, Ghent University, 9052 Ghent, Belgium and Flanders Make-EEDT, 3001 Leuven, Belgium
3 shared publicationsPeter Sergeant
Electrical Energy Laboratory, EEMMeCS, Ghent University, Ghent, Belgium
2 shared publications- Ahmed Hemeida
Aalto University
1 shared publication - Hendrik Vansompel
Ghent University
1 shared publication Luc Dupré
Department of EESA, Electrical Energy Laboratory, Ghent University, Technologiepark-Zwijnaarde 913, 9052 Gent, Belgium
1 shared publication
Latest Publications
- 18 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (3) , 1-10
Evaluation of the Rotor Eddy-Current Losses in High-Speed PMSMs With a Shielding Cylinder for Different Stator Sources
A continuous demand for more efficient and more compact drives is pushing the popularity of high-speed permanent magnet synchronous machines (PMSMs). However, high rotational speeds and extreme power densities imply that an appropriate cooling of the rotor may be difficult. This is all the more important because of the risk of demagnetization when permanent magnets are operated at high temperatures. Therefore, it is paramount to reduce the losses in the rotor of high-speed machines as much as possible. One technique to reduce the eddy-current losses is introducing a shielding cylinder, i.e., a conductive sleeve that is wrapped around the magnets. However, when badly designed, such a shielding cylinder may increase, rather than decrease, the losses. Therefore, an in-depth study of the effect of the shielding cylinder on the eddy-current losses in high-speed PMSMs is required. By studying how the eddy-current losses are affected by the shielding cylinder's thickness and its conductivity, this paper aims at providing more insight in how the eddy-current losses can be reduced. Moreover, the study of the eddy-current losses is repeated for different stator sources to evaluate the importance of accounting for the actual control strategy during the machine's design.
- 18 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (3) , 1-10
Evaluation of the Rotor Eddy-Current Losses in High-Speed PMSMs With a Shielding Cylinder for Different Stator Sources
A continuous demand for more efficient and more compact drives is pushing the popularity of high-speed permanent magnet synchronous machines (PMSMs). However, high rotational speeds and extreme power densities imply that an appropriate cooling of the rotor may be difficult. This is all the more important because of the risk of demagnetization when permanent magnets are operated at high temperatures. Therefore, it is paramount to reduce the losses in the rotor of high-speed machines as much as possible. One technique to reduce the eddy-current losses is introducing a shielding cylinder, i.e., a conductive sleeve that is wrapped around the magnets. However, when badly designed, such a shielding cylinder may increase, rather than decrease, the losses. Therefore, an in-depth study of the effect of the shielding cylinder on the eddy-current losses in high-speed PMSMs is required. By studying how the eddy-current losses are affected by the shielding cylinder's thickness and its conductivity, this paper aims at providing more insight in how the eddy-current losses can be reduced. Moreover, the study of the eddy-current losses is repeated for different stator sources to evaluate the importance of accounting for the actual control strategy during the machine's design.
- 9 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 33 (1) , 281-289
Computational-Time Reduction of Fourier-Based Analytical Models
An increasing interest in both efficient electric machines and more extensive control strategies demands evermore faster simulation tools. In that context, Fourier-based models, which combine low computational times with a high accuracy, have already proven their value. However, even Fourier-based models may encounter problems related to CPU usage. To cope with these problems the authors present a number of simple techniques to reduce the computational effort of Fourier-based models for synchronous machines. The techniques are based on simplifying the studied geometry and a qualitative analysis of the machine's time- and spatial-harmonic content. The proposed techniques are validated and a benchmark test has shown that a great reduction in computational burden can be achieved without significant loss of accuracy. The preliminary harmonic analysis gives, by far, the largest reduction of the computational burden.
- 9 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 33 (1) , 281-289
Computational-Time Reduction of Fourier-Based Analytical Models
An increasing interest in both efficient electric machines and more extensive control strategies demands evermore faster simulation tools. In that context, Fourier-based models, which combine low computational times with a high accuracy, have already proven their value. However, even Fourier-based models may encounter problems related to CPU usage. To cope with these problems the authors present a number of simple techniques to reduce the computational effort of Fourier-based models for synchronous machines. The techniques are based on simplifying the studied geometry and a qualitative analysis of the machine's time- and spatial-harmonic content. The proposed techniques are validated and a benchmark test has shown that a great reduction in computational burden can be achieved without significant loss of accuracy. The preliminary harmonic analysis gives, by far, the largest reduction of the computational burden.
- 29 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (10) , 1-8
Study of the Effect of a Shielding Cylinder on the Torque in a Permanent-Magnet Synchronous Machine Considering Two Torque-Producing Mechanisms
Despite an ever-growing interest, a lot of questions related to the design and operation of high-speed permanent-magnet synchronous machines remain unanswered. One aspect of such high-speed machines that requires special attention is the effect of the shielding cylinder (SC), a conductive sleeve that is wrapped around the magnets and which’ goal is to reduce the rotor losses and/or retain the magnets. Therefore, this paper aims at theoretically studying the effect of the SC on the torque production. The study is performed using a 2-D analytical subdomain model that accounts for slotting and the eddy-current reaction field. The torque is divided in two components, the classical torque due to interaction between the magnets and the stator currents and the torque due to interaction with the eddy currents in the SC. This approach is unique and results in a better insight in the machine’s physics.
- 29 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (10) , 1-8
Study of the Effect of a Shielding Cylinder on the Torque in a Permanent-Magnet Synchronous Machine Considering Two Torque-Producing Mechanisms
Despite an ever-growing interest, a lot of questions related to the design and operation of high-speed permanent-magnet synchronous machines remain unanswered. One aspect of such high-speed machines that requires special attention is the effect of the shielding cylinder (SC), a conductive sleeve that is wrapped around the magnets and which’ goal is to reduce the rotor losses and/or retain the magnets. Therefore, this paper aims at theoretically studying the effect of the SC on the torque production. The study is performed using a 2-D analytical subdomain model that accounts for slotting and the eddy-current reaction field. The torque is divided in two components, the classical torque due to interaction between the magnets and the stator currents and the torque due to interaction with the eddy currents in the SC. This approach is unique and results in a better insight in the machine’s physics.
- 7 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (00189464) , 1
Time- and Spatial-Harmonic Content in Synchronous Electrical Machines
The use of power electronics has led to a growing importance of higher time-harmonic content in electrical machines. To gain insight in phenomena related to these higher harmonics, such as noise and losses, a good understanding of the magnetic field's harmonic content is mandatory. Moreover, the development of fast and accurate, harmonic-based, analytical models requires a qualitative knowledge of the machine's time- and spatial-harmonic content. Although the harmonic content of electric machines is an extensively studied topic, previous publications tended to focus on one type of synchronous machines and often did not consider higher time-harmonic orders. This paper complements the existing theory by providing a more general approach, thereby covering machines and operating points that were not covered until now. It considers both three-phase and multi-phase machines with an odd number of phases. The winding distribution can either have an integer or a fractional number of slots per pole and per phase, and higher time-harmonic content is regarded as well. Note that the saturation is neglected. Despite its general validity, this paper succeeds at providing one simple equation to determine the machine's time-and spatial-harmonic content. Moreover, this paper also extensively discusses the physical causes of the harmonic content. The combination of this general validity, the simple result, and the insight in the physics makes that this paper is a strong tool to both study harmonic-related phenomena in electric machines and to develop harmonic-based analytical models.
- 7 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (00189464) , 1
Time- and Spatial-Harmonic Content in Synchronous Electrical Machines
The use of power electronics has led to a growing importance of higher time-harmonic content in electrical machines. To gain insight in phenomena related to these higher harmonics, such as noise and losses, a good understanding of the magnetic field's harmonic content is mandatory. Moreover, the development of fast and accurate, harmonic-based, analytical models requires a qualitative knowledge of the machine's time- and spatial-harmonic content. Although the harmonic content of electric machines is an extensively studied topic, previous publications tended to focus on one type of synchronous machines and often did not consider higher time-harmonic orders. This paper complements the existing theory by providing a more general approach, thereby covering machines and operating points that were not covered until now. It considers both three-phase and multi-phase machines with an odd number of phases. The winding distribution can either have an integer or a fractional number of slots per pole and per phase, and higher time-harmonic content is regarded as well. Note that the saturation is neglected. Despite its general validity, this paper succeeds at providing one simple equation to determine the machine's time-and spatial-harmonic content. Moreover, this paper also extensively discusses the physical causes of the harmonic content. The combination of this general validity, the simple result, and the insight in the physics makes that this paper is a strong tool to both study harmonic-related phenomena in electric machines and to develop harmonic-based analytical models.
- Open Access
- 31 October 2016
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2016, 1-14
Comparison of Three Analytical Methods for the Precise Calculation of Cogging Torque and Torque Ripple in Axial Flux PM Machines
A comparison between different analytical and finite-element (FE) tools for the computation of cogging torque and torque ripple in axial flux permanent-magnet synchronous machines is made. 2D and 3D FE models are the most accurate for the computation of cogging torque and torque ripple. However, they are too time consuming to be used for optimization studies. Therefore, analytical tools are also used to obtain the cogging torque and torque ripple. In this paper, three types of analytical models are considered. They are all based on dividing the machine into many slices in the radial direction. One model computes the lateral force based on the magnetic field distribution in the air gap area. Another model is based on conformal mapping and uses complex Schwarz Christoffel (SC) transformations. The last model is based on the subdomain technique, which divides the studied geometry into a number of separate domains. The different types of models are compared for different slot openings and permanent-magnet widths. One of the main conclusions is that the subdomain model is best suited to compute the cogging torque and torque ripple with a much higher accuracy than the SC model.
- 31 October 2016
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2016, 1-14
Open AccessComparison of Three Analytical Methods for the Precise Calculation of Cogging Torque and Torque Ripple in Axial Flux PM Machines
A comparison between different analytical and finite-element (FE) tools for the computation of cogging torque and torque ripple in axial flux permanent-magnet synchronous machines is made. 2D and 3D FE models are the most accurate for the computation of cogging torque and torque ripple. However, they are too time consuming to be used for optimization studies. Therefore, analytical tools are also used to obtain the cogging torque and torque ripple. In this paper, three types of analytical models are considered. They are all based on dividing the machine into many slices in the radial direction. One model computes the lateral force based on the magnetic field distribution in the air gap area. Another model is based on conformal mapping and uses complex Schwarz Christoffel (SC) transformations. The last model is based on the subdomain technique, which divides the studied geometry into a number of separate domains. The different types of models are compared for different slot openings and permanent-magnet widths. One of the main conclusions is that the subdomain model is best suited to compute the cogging torque and torque ripple with a much higher accuracy than the SC model.
- Open Access
- 1 October 2015
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2015, 1-8
Voltage Sources in 2D Fourier-Based Analytical Models of Electric Machines
The importance of extensive optimizations during the design of electric machines entails a need for fast and accurate simulation tools. For that reason, Fourier-based analytical models have gained a lot of popularity. The problem, however, is that these models typically require a current density as input. This is in contrast with the fact that the great majority of modern drive trains are powered with the help of a pulse-width modulated voltage-source inverter. To overcome that mismatch, this paper presents a coupling of classical Fourier-based models with the equation for the terminal voltage of an electric machine, a technique that is well known in finite-element modeling but has not yet been translated to Fourier-based analytical models. Both a very general discussion of the technique and a specific example are discussed. The presented work is validated with the help of a finite-element model. A very good accuracy is obtained.
- 1 October 2015
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2015, 1-8
Open AccessVoltage Sources in 2D Fourier-Based Analytical Models of Electric Machines
The importance of extensive optimizations during the design of electric machines entails a need for fast and accurate simulation tools. For that reason, Fourier-based analytical models have gained a lot of popularity. The problem, however, is that these models typically require a current density as input. This is in contrast with the fact that the great majority of modern drive trains are powered with the help of a pulse-width modulated voltage-source inverter. To overcome that mismatch, this paper presents a coupling of classical Fourier-based models with the equation for the terminal voltage of an electric machine, a technique that is well known in finite-element modeling but has not yet been translated to Fourier-based analytical models. Both a very general discussion of the technique and a specific example are discussed. The presented work is validated with the help of a finite-element model. A very good accuracy is obtained.