Dimas Pristovani Riananda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dimas Pristovani Riananda has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Dadet Pramadihanto
Politeknik Elektronika Negeri Surabaya
10 shared publications - Eko Henfri Binugroho
EEPIS Robotics Research Center (ER2C) Electronics Engineering Polytechnic Institute of Surabaya (EEPIS) St. Raya ITS, Keputih, Sukolilo, Surabaya, Indonesia, 60111
3 shared publications - Afif Zuhri Arfianto
Politeknik Perkapalan Negeri Surabaya
2 shared publications Dewanto Sanggar
Politeknik Elektronika Negeri Surabaya
2 shared publicationsRaden Sanggar Dewanto
Politeknik Elektronika Negeri Surabaya,EEPIS Robotic Research CenterSurabayaIndonesia
2 shared publicationsSanggar Dewanto
EEPIS Robotics Research Center (ER2C) Electronics Engineering Polytechnic Institute of Surabaya (EEPIS) / Politeknik Elektronika Negeri Surabaya (PENS), Surabaya, 60111, Indonesia
2 shared publications
Latest Publications
- Open Access
- 30 September 2026
- Published by Indonesian Society of Applied Science (ISAS) in Journal of Advanced Vocational Information and Communication Technology
- Vol. 1 (3) , 141-153
Implementation of a Kalman Filter to Improve RSSI-Based Trilateration Accuracy Using the LoRa RFM95W Module
Internet of Things (IoT)-based positioning has become increasingly important for monitoring and navigation applications. This study proposes a LoRa-based positioning system using Received Signal Strength Indicator (RSSI) measurements filtered by a Kalman Filter. The filtered RSSI values are converted into distance using the Log-Distance Path Loss model, while the target position is estimated through trilateration. Positioning accuracy is evaluated by comparing the estimated coordinates with GPS coordinates obtained from a u-blox NEO-6M module using the Haversine distance. Experimental results show that the Kalman Filter improves RSSI stability and reduces distance fluctuations, leading to more consistent position estimates. However, the positioning accuracy remains lower than GPS, particularly in dynamic environments. Despite this limitation, the proposed system demonstrates the potential of LoRa as a low-power, long-range positioning solution. Future work will focus on adaptive filtering methods to further improve positioning accuracy.
- 30 September 2026
- Published by Indonesian Society of Applied Science (ISAS) in Journal of Advanced Vocational Information and Communication Technology
- Vol. 1 (3) , 141-153
Open AccessImplementation of a Kalman Filter to Improve RSSI-Based Trilateration Accuracy Using the LoRa RFM95W Module
Internet of Things (IoT)-based positioning has become increasingly important for monitoring and navigation applications. This study proposes a LoRa-based positioning system using Received Signal Strength Indicator (RSSI) measurements filtered by a Kalman Filter. The filtered RSSI values are converted into distance using the Log-Distance Path Loss model, while the target position is estimated through trilateration. Positioning accuracy is evaluated by comparing the estimated coordinates with GPS coordinates obtained from a u-blox NEO-6M module using the Haversine distance. Experimental results show that the Kalman Filter improves RSSI stability and reduces distance fluctuations, leading to more consistent position estimates. However, the positioning accuracy remains lower than GPS, particularly in dynamic environments. Despite this limitation, the proposed system demonstrates the potential of LoRa as a low-power, long-range positioning solution. Future work will focus on adaptive filtering methods to further improve positioning accuracy.
- Open Access
- 1 August 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 16 (4)
Implementation of support vector machine on LVMDP panel with overheating protection system
Electricity is a critical requirement in industrial operations, where the continuity and stability of power distribution directly affect safety and productivity. The low voltage main distribution panel (LVMDP) functions as the main node of electrical power distribution; however, conventional LVMDP systems generally lack intelligent protection mechanisms capable of detecting overheating-related fire hazards and initiating preventive action before failure occurs. This study proposes an intelligent monitoring and protection system for LVMDP panels that combines real-time multi-sensor monitoring, support vector machine (SVM)-based hazard classification, and an automatic shutdown mechanism. The main contribution of this work lies in the integration of predictive thermal risk detection with autonomous protective action, enabling the system not only to monitor panel conditions but also to respond immediately to hazardous states before they escalate into fire incidents. SVM was selected because of its strong capability to classify complex and nonlinear patterns from sensor data with high reliability. The developed system continuously evaluates panel conditions and triggers auto-shutdown when an overheating risk is identified, thereby improving preventive protection compared with conventional alarm-based monitoring systems. Experimental results show that the sensor measurements achieved error rates mostly below 5% compared with calibrated instruments, indicating good accuracy. In addition, the SVM model obtained an overall accuracy of 93%, with a macro-average F1-score of 92% and a weighted-average F1-score of 93%. These results demonstrate that the proposed system is effective for early detection and active protection of LVMDP panels against overheating hazards.
- 1 August 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 16 (4)
Open AccessImplementation of support vector machine on LVMDP panel with overheating protection system
Electricity is a critical requirement in industrial operations, where the continuity and stability of power distribution directly affect safety and productivity. The low voltage main distribution panel (LVMDP) functions as the main node of electrical power distribution; however, conventional LVMDP systems generally lack intelligent protection mechanisms capable of detecting overheating-related fire hazards and initiating preventive action before failure occurs. This study proposes an intelligent monitoring and protection system for LVMDP panels that combines real-time multi-sensor monitoring, support vector machine (SVM)-based hazard classification, and an automatic shutdown mechanism. The main contribution of this work lies in the integration of predictive thermal risk detection with autonomous protective action, enabling the system not only to monitor panel conditions but also to respond immediately to hazardous states before they escalate into fire incidents. SVM was selected because of its strong capability to classify complex and nonlinear patterns from sensor data with high reliability. The developed system continuously evaluates panel conditions and triggers auto-shutdown when an overheating risk is identified, thereby improving preventive protection compared with conventional alarm-based monitoring systems. Experimental results show that the sensor measurements achieved error rates mostly below 5% compared with calibrated instruments, indicating good accuracy. In addition, the SVM model obtained an overall accuracy of 93%, with a macro-average F1-score of 92% and a weighted-average F1-score of 93%. These results demonstrate that the proposed system is effective for early detection and active protection of LVMDP panels against overheating hazards.
- Open Access
- 31 December 2025
- Published by Atlantis Press SARL
- p. 343-349
Introduction of Artificial Intelligence-Based Traditional Fishing Vessel Innovation to Increase Fish Catch Results in Brondong Lamongan East Java
- 31 December 2025
- Published by Atlantis Press SARL
- p. 343-349
Open AccessIntroduction of Artificial Intelligence-Based Traditional Fishing Vessel Innovation to Increase Fish Catch Results in Brondong Lamongan East Java
- Open Access
- 31 July 2023
- Published by Politeknik Negeri Malang in Jurnal Elektronika dan Otomasi Industri
- Vol. 10 (2) , 175-182
Perancangan Strategi Keputusan Robot Sepak Bola Beroda menggunakan Metode Decision Tree
Kontes Robot Sepak Bola Beroda (KRSBI – Beroda) tahun 2022 telah diadakan secara luring. Kemampuan utama yang harus dimiliki robot saat pertandingan adalah mencari, mengumpan, menggiring, dan menendang bola ke gawang. Namun, masih banyak tim kontestan yang langsung menendang ketika mendapat bola. Hal tersebut disebabkan dikarenakan robot tidak bisa membuat keputusan yang baik sehingga kemungkinan terjadinya gol menjadi kecil. Melihat permasalahan tersebut, maka diberikan solusi yaitu penerapan metode decision tree sebagai strategi keputusan mengumpan, menggiring, menghindar, atau menendang. Pengambilan keputusan akan ditentukan oleh beberapa faktor, yaitu posisi robot, posisi kawan, posisi gawang, dan posisi robot lawan. Waktu respon robot mencari gawang lawan dan kecepatan robot menghadap ke gawang lawan memiliki rata-rata 2.46 detik dengan range jarak X terhadap gawang = 500-6000, dan range Y terhadap gawang = 500. Hasil nilai gain terbesar yaitu pada bola dengan nilai 1 akan dijadikan node utama atau root node. Dari pohon keputusan robot dapat membuat keputusan mengumpan, menghindar, menggiring, atau langsung menendang ke gawang lawan lebih efisien dan efektif.
- 31 July 2023
- Published by Politeknik Negeri Malang in Jurnal Elektronika dan Otomasi Industri
- Vol. 10 (2) , 175-182
Open AccessPerancangan Strategi Keputusan Robot Sepak Bola Beroda menggunakan Metode Decision Tree
Kontes Robot Sepak Bola Beroda (KRSBI – Beroda) tahun 2022 telah diadakan secara luring. Kemampuan utama yang harus dimiliki robot saat pertandingan adalah mencari, mengumpan, menggiring, dan menendang bola ke gawang. Namun, masih banyak tim kontestan yang langsung menendang ketika mendapat bola. Hal tersebut disebabkan dikarenakan robot tidak bisa membuat keputusan yang baik sehingga kemungkinan terjadinya gol menjadi kecil. Melihat permasalahan tersebut, maka diberikan solusi yaitu penerapan metode decision tree sebagai strategi keputusan mengumpan, menggiring, menghindar, atau menendang. Pengambilan keputusan akan ditentukan oleh beberapa faktor, yaitu posisi robot, posisi kawan, posisi gawang, dan posisi robot lawan. Waktu respon robot mencari gawang lawan dan kecepatan robot menghadap ke gawang lawan memiliki rata-rata 2.46 detik dengan range jarak X terhadap gawang = 500-6000, dan range Y terhadap gawang = 500. Hasil nilai gain terbesar yaitu pada bola dengan nilai 1 akan dijadikan node utama atau root node. Dari pohon keputusan robot dapat membuat keputusan mengumpan, menghindar, menggiring, atau langsung menendang ke gawang lawan lebih efisien dan efektif.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2706 (1)
Design and development of virtual digital assistant for fishers with fish distribution based on lora RFM95 communication
The waters region in Indonesia are immense and have a tremendous potential natural resource for marine businesses, especially fisheries. Many Indonesians, especially those living in coastal areas, make fishing their source of livelihood. Currently, the technology that is commonly used to support the work of fishers in catching fish is the Fish Finder. However, there are still very few Fish Finder users because the tools are too expensive and complicated for fishers to obtain. In this study, a Digital Virtual Assistant is created to communicate and navigate in the search for fish distribution. In addition, this tool can simplify the work of fishers and save fuel costs, so that it is beneficial in terms of the economy aspect. This tool works by receiving data from land with LoRa RFM95 communication which indicates the potential presence of fish. The device works based on Latitude and Longitude data from the Marine Research and Observation Center. By entering required data, Virtual Digital Assistant will show the distance and direction to the location of fish distribution. This is result of system testing, the GPS sensor used in the Digital Virtual Assistant Ublox NEO-7m has an accuracy level with an average distance value of 3.220921 meters. The communication distance using portable devices with PC systems using LoRa with 3dBi antennas can reach 1.41 kilometers in a condition without obstructions between nodes. The delay in updating the ship coordinate data on the interface has the lowest average of 30.8 seconds.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2706 (1)
Open AccessDesign and development of virtual digital assistant for fishers with fish distribution based on lora RFM95 communication
The waters region in Indonesia are immense and have a tremendous potential natural resource for marine businesses, especially fisheries. Many Indonesians, especially those living in coastal areas, make fishing their source of livelihood. Currently, the technology that is commonly used to support the work of fishers in catching fish is the Fish Finder. However, there are still very few Fish Finder users because the tools are too expensive and complicated for fishers to obtain. In this study, a Digital Virtual Assistant is created to communicate and navigate in the search for fish distribution. In addition, this tool can simplify the work of fishers and save fuel costs, so that it is beneficial in terms of the economy aspect. This tool works by receiving data from land with LoRa RFM95 communication which indicates the potential presence of fish. The device works based on Latitude and Longitude data from the Marine Research and Observation Center. By entering required data, Virtual Digital Assistant will show the distance and direction to the location of fish distribution. This is result of system testing, the GPS sensor used in the Digital Virtual Assistant Ublox NEO-7m has an accuracy level with an average distance value of 3.220921 meters. The communication distance using portable devices with PC systems using LoRa with 3dBi antennas can reach 1.41 kilometers in a condition without obstructions between nodes. The delay in updating the ship coordinate data on the interface has the lowest average of 30.8 seconds.
- 22 April 2020
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2226 (1) , 060008
Propulsion selection method using motor thrust table for optimum flight in multirotor aircraft
One of the problems when designing an aircraft is flight time estimation. When we design the aircraft, in general, calculating the maximum takeoff weight becomes the priority. The longer flight time required by the aircraft, the more batteries should be added. More batteries mean the payload capacity of the aircraft is decreased. On the other hand, adding more weight will increase the requirement of using more powerful motors. We need to take into our account, that using powerful motors should be calculated carefully because the current consumption is also increased. This problem is circling in the same situation, without any real solution to overcome the problem. As unmanned aircraft has become a critical part of human life for example in surveillance, agricultural, and medicine delivery mission, obtaining the optimum and efficient flight time is vital. In this research, we propose a novel approach of maximum takeoff weight calculation that is needed when designing the aircraft by looking at the complete map of motor specifications. The goal of this paper is to help any aircraft user from hobbyist to professional to determine whether their aircraft design is feasible.
- 22 April 2020
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2226 (1) , 060008
Propulsion selection method using motor thrust table for optimum flight in multirotor aircraft
One of the problems when designing an aircraft is flight time estimation. When we design the aircraft, in general, calculating the maximum takeoff weight becomes the priority. The longer flight time required by the aircraft, the more batteries should be added. More batteries mean the payload capacity of the aircraft is decreased. On the other hand, adding more weight will increase the requirement of using more powerful motors. We need to take into our account, that using powerful motors should be calculated carefully because the current consumption is also increased. This problem is circling in the same situation, without any real solution to overcome the problem. As unmanned aircraft has become a critical part of human life for example in surveillance, agricultural, and medicine delivery mission, obtaining the optimum and efficient flight time is vital. In this research, we propose a novel approach of maximum takeoff weight calculation that is needed when designing the aircraft by looking at the complete map of motor specifications. The goal of this paper is to help any aircraft user from hobbyist to professional to determine whether their aircraft design is feasible.
- 22 April 2020
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2226 (1) , 060010
Smart pulley workflow in delivery drone for goods transportation
Delivery drone is one of tools for supporting the realization of industry 4.0 especially in the E-commerce industry. A lot of delivery drone were proposed to solve the goods transportation problems. We are building a delivery drone with single wire pulley mechanical system. We find that just only using advanced mechanical design and physics laws, our delivery drone can detect the landing phase and maximum phase without any advanced sensor requirement. This paper explains how we manage the workflow of how to control the pulley mechanical system with those mechanical sensors to obtain a smart pulley system. Not only how to control the pulley, this paper also discusses about the safety workflow for emergency case during dropping the goods. Based on the experiment, the successful dropping process by using automatic workflow are 90% and 10% with manual workflow as safety workflow.
- 22 April 2020
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2226 (1) , 060010
Smart pulley workflow in delivery drone for goods transportation
Delivery drone is one of tools for supporting the realization of industry 4.0 especially in the E-commerce industry. A lot of delivery drone were proposed to solve the goods transportation problems. We are building a delivery drone with single wire pulley mechanical system. We find that just only using advanced mechanical design and physics laws, our delivery drone can detect the landing phase and maximum phase without any advanced sensor requirement. This paper explains how we manage the workflow of how to control the pulley mechanical system with those mechanical sensors to obtain a smart pulley system. Not only how to control the pulley, this paper also discusses about the safety workflow for emergency case during dropping the goods. Based on the experiment, the successful dropping process by using automatic workflow are 90% and 10% with manual workflow as safety workflow.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 120-125
Speed and Balancing Control of Two Cables Pulley-Gripper System for Delivery Drone
The important thing that should be consist on delivery drone is landing speed and dropping object with smoothly. For the two cables and two motor pulley system, balancing control are use to balancing the cable that carrying the gripper, while the speed on landing system are controlled. The main advantage to build the system are using balancing PID controller with cable length input and speed control to makes the pulley automatically landing and pulling the object. The object can be land smoothly with speed control, and the cable will be in stable parallel position when the pulley are rotating with balancing control. To detect the object height, we use the proximity sensor and calibrating with rotary encoder. In this paper, we have installed the speed and balancing control on the two cables pulley-gripper system for delivery drone. The final result, the pulley can be land the box smoothly from 4 - 5 meters distance and stable the cable distance with error less than 2 cm respectively.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 120-125
Speed and Balancing Control of Two Cables Pulley-Gripper System for Delivery Drone
The important thing that should be consist on delivery drone is landing speed and dropping object with smoothly. For the two cables and two motor pulley system, balancing control are use to balancing the cable that carrying the gripper, while the speed on landing system are controlled. The main advantage to build the system are using balancing PID controller with cable length input and speed control to makes the pulley automatically landing and pulling the object. The object can be land smoothly with speed control, and the cable will be in stable parallel position when the pulley are rotating with balancing control. To detect the object height, we use the proximity sensor and calibrating with rotary encoder. In this paper, we have installed the speed and balancing control on the two cables pulley-gripper system for delivery drone. The final result, the pulley can be land the box smoothly from 4 - 5 meters distance and stable the cable distance with error less than 2 cm respectively.
- Open Access
- 1 February 2019
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 9 (1) , 203-214
Implementation and design of new low-cost foot pressure sensor module using piezoelectric sensor in T-FLoW humanoid robot
Basically, human can sense the active body force trough the soles of their feet and can feel the position vector of zero moment point (ZMP) based on the center of pressure (CoP) from active body force. This behavior is adapted by T-FLoW humanoid robot using unique sensor which is piezoelectric sensor. Piezoelectric sensor has a characteristic which is non-continuous reading (record a data only a moment). Because of it, this sensor cannot be used to stream data such as flex sensor, loadcell sensor, and torque sensor like previous research. Therefore, the piezoelectric sensor still can be used to measure the position vector of ZMP. The idea is using this sensor in a special condition which is during landing condition. By utilizing 6 unit of piezoelectric sensor with a certain placement, the position vector of ZMP (X-Y-axis) and pressure value in Z-axis from action body force can be found. The force resultant method is used to find the position vector of ZMP from each piezoelectric sensor. Based on those final conclusions in each experiment, the implementation of foot pressure sensor modul using piezoelectric sensor has a good result (94%) as shown in final conclusions in each experiment. The advantages of this new foot pressure sensor modul is low-cost design and similar result with another sensor. The disadvantages of this sensor are because of the main characteristic of piezoelectric sensor (non-continuous read) sometimes the calculation has outlayer data.
- 1 February 2019
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 9 (1) , 203-214
Open AccessImplementation and design of new low-cost foot pressure sensor module using piezoelectric sensor in T-FLoW humanoid robot
Basically, human can sense the active body force trough the soles of their feet and can feel the position vector of zero moment point (ZMP) based on the center of pressure (CoP) from active body force. This behavior is adapted by T-FLoW humanoid robot using unique sensor which is piezoelectric sensor. Piezoelectric sensor has a characteristic which is non-continuous reading (record a data only a moment). Because of it, this sensor cannot be used to stream data such as flex sensor, loadcell sensor, and torque sensor like previous research. Therefore, the piezoelectric sensor still can be used to measure the position vector of ZMP. The idea is using this sensor in a special condition which is during landing condition. By utilizing 6 unit of piezoelectric sensor with a certain placement, the position vector of ZMP (X-Y-axis) and pressure value in Z-axis from action body force can be found. The force resultant method is used to find the position vector of ZMP from each piezoelectric sensor. Based on those final conclusions in each experiment, the implementation of foot pressure sensor modul using piezoelectric sensor has a good result (94%) as shown in final conclusions in each experiment. The advantages of this new foot pressure sensor modul is low-cost design and similar result with another sensor. The disadvantages of this sensor are because of the main characteristic of piezoelectric sensor (non-continuous read) sometimes the calculation has outlayer data.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 23-28
Development and Performance Testing of FLoWRTOS with Random Case: 3 Main Processes on The Head System of T-FLoW Robot
The real-time operating system (RTOS) is a software that contains the resources of a hardware device, and provides the facility to run the application in real-time by doing the task according to the given deadline. FLoWRTOS is a RTOS running on an embedded system device, which is being built by the EEPIS Robotics Research Center (ER2C) on the ARM Cortex-M4 platform of the i.MX6SoloX processor. In contrast to the real-time operating system in general, FLoWRTOS performs task scheduling based on deadline priority, this allows performance of FLoWRTOS to be optimized in the absence of an idle time of all the scheduled tasks. Tests were conducted to evaluate the performance of FLoWRTOS, and also on the implementation of FLoWRTOS on a plant, which is the head system of T-FLoW robot. The result shows that FLoWRTOS can run many tasks with a condition that the CPU utilization is less than equal to 0.8. And if the CPU utilization approaches less than equal to 1, at a certain time it will cause the task to run past the deadline because FLoWRTOS is still non-preemptive.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 23-28
Development and Performance Testing of FLoWRTOS with Random Case: 3 Main Processes on The Head System of T-FLoW Robot
The real-time operating system (RTOS) is a software that contains the resources of a hardware device, and provides the facility to run the application in real-time by doing the task according to the given deadline. FLoWRTOS is a RTOS running on an embedded system device, which is being built by the EEPIS Robotics Research Center (ER2C) on the ARM Cortex-M4 platform of the i.MX6SoloX processor. In contrast to the real-time operating system in general, FLoWRTOS performs task scheduling based on deadline priority, this allows performance of FLoWRTOS to be optimized in the absence of an idle time of all the scheduled tasks. Tests were conducted to evaluate the performance of FLoWRTOS, and also on the implementation of FLoWRTOS on a plant, which is the head system of T-FLoW robot. The result shows that FLoWRTOS can run many tasks with a condition that the CPU utilization is less than equal to 0.8. And if the CPU utilization approaches less than equal to 1, at a certain time it will cause the task to run past the deadline because FLoWRTOS is still non-preemptive.