Comparative Study of the Effectiveness of Laboratory‐Formulated Polishing Pastes for Two CAD/CAM Ceramic Restorative Materials
- 24 October 2021
- journal article
- research article
- Published by Wiley in Journal of Prosthodontics
- Vol. 31 (6) , 529-536
Abstract
Purpose : To evaluate the effect of different polishing pastes with different particle sizes on the surface finish of two different CAD/CAM ceramics. Materials and Methods : A total of 128 specimens were prepared of two CAD/CAM ceramics: lithium disilicate (12.4×14.5×2mm) and monolithic zirconia (17.5×12.5×2.5mm). They were divided randomly into 8 groups according to surface treatment (n = 8). Group 1 (control) was left as received after crystallization or sintering with no further surface treatment; Group 2 (glazed); Group 3 (positive control), where specimens were polished using standardized surface treatment (medium grit silicon carbide discs, rubber cup and pumice slurry, then rubber cup and toothpaste). For groups 4–8, in addition to silicon carbide and pumice slurry polishing, specimens were further polished using a diamond paste (DP), and polishing pastes of microzirconia (MZ), nanosilica (NS), nanodiamond (ND), and nanozirconia (NZ), respectively. Surface roughness (Ra) was measured using non-contact profilometer. The mean values were compared using ANOVA and Post-Hoc Tukey's test (α = 0.05). Specimens’ surfaces were studied using a scanning electron microscope (SEM). Results : Positive control group and MZ exhibited significant Ra of lithium disilicate compared to control (P˂0.001), glazed (P = 0.001), DPs (P = 0.002), NS (P˂0.001), ND (P˂0.001), and NZ (P = 0.002). In the case of zirconia, positive control showed a significantly higher Ra compared to all other groups (p˂0.001). No statistical difference was found between all other polishing techniques (positive control, glazed, DPs, NS, ND, MZ and NZ) (P>0.05). Conclusion : Polishing with ND, NZ and NS lab-formulated pastes produced surfaces with comparable smoothness to control and glazed specimens for lithium disilicate and zirconia ceramic materials. This article is protected by copyright. All rights reservedKeywords
This publication has 26 references indexed in Scilit:
- Surface Evaluation of Polishing Techniques for New ResilientCAD/CAMRestorative MaterialsJournal of Esthetic and Restorative Dentistry, 2015
- Effects of surface-finishing protocols on the roughness, color change, and translucency of different ceramic systemsThe Journal of Prosthetic Dentistry, 2014
- Current status of zirconia restorationJournal of Prosthodontic Research, 2013
- Implant‐Supported Fixed Dental Prostheses with CAD/CAM‐Fabricated Porcelain Crown and Zirconia‐Based FrameworkJournal of Prosthodontics, 2013
- Wear performance of dental ceramics after grinding and polishing treatmentsJournal of the Mechanical Behavior of Biomedical Materials, 2012
- Performance of Different Polishing Techniques for Direct CAD/CAM Ceramic RestorationsOperative Dentistry, 2010
- Clinical evaluation of all-ceramic crowns fabricated from intraoral digital impressions based on the principle of active wavefront samplingJournal of Dentistry, 2010
- Evaluation of Different Methods of Optical Impression Making on the Marginal Gap of Onlays Created with CEREC 3DOperative Dentistry, 2010
- Wear of ceramic and antagonist—A systematic evaluation of influencing factors in vitroDental Materials, 2008
- Abrasive Finishing and Polishing in Restorative Dentistry: A State-of-the-Art ReviewDental Clinics of North America, 2007