INFLUENCE OF ACTIVE GAS CONTENT IN POWDER ON MECHANICAL PROPERTIES OF WORKPIECE BLANKS PRODUCED BY PLASMA ADDITIVE TECHNOLOGIES
Open Access
- 29 January 2025
- journal article
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 4,p. 52-58
Abstract
Purpose. Analysis of the influence of powder quality (content of active gases) on the level of mechanical properties of workpieces produced by plasma additive technologies. Research methods. Chemical composion of the powders was determined in accordance with regulatory document. The presence of non-metallic inclusions and contaminants in the powders was determined visualy. To quantify the oxygen in the powders, the vacuum extraction method was used in accordance with ДСТУ ISO 4491-4:2016. Oxygen and nitrogen gas analyser TC 500 (company LECO). Before being loaded into the dosing unit, all powders were dried in an oven (temperature - 250°C, for 1 hour). Samples (size 130×70×14 mm) were produced by additive growth by plasma powder surfacing (PPS) on a specialised robotic device STARWELD 190H. The chemical composition of the grown samples was determined by the spectral method using a SPECTROMAX optical emission spectrometer according to standard methods in accordance with ГОСТ19863.1-19863.12. The content of nitrogen and oxygen in the deposited metal was determined in accordance with TC 500 (company LECO). Microstructural analysis were carried out on the samples in the longitudinal and cross directions before and after heat treatment, after etching in a reagent for electrowinning of heat-resistant alloys (Н3РО4 – 800 ml +CrО3 – 100ml). The mechanical properties of the alloy were obtained on standard cylindrical samples according to ГОСТ 1497-84, ГОСТ 1497-84, ГОСТ 10145-81s. Results. The chemical composition of the deposited metal is determined by the chemical composition of the powder. The content of oxygen and nitrogen in the deposited metal is determined by the content of these elements in the powder itself, as well as by the protection of the weld pool with argon. It has been established that in the alloy ЭП-648ВИ when the powder contains nitrogen in the amount of [N] ≥ 0.03 wt. %, or oxygen in [O] ≥ 0.02 wt. % in the deposited metal at a temperature of 1100 °C, a significant decrease in its deformation capacity (ε ≤ 3.8 %) is recorded, which under the influence of thermal stresses leads to the appearance of hot cracks, and as a result, we see a significant decrease in the strength and plasticity in the longitudinal direction. Scientific novelty. The influence of the quality of the alloy ЕП-648ВИ powder on the properties of workpieces obtained using additive technologies has been established. Practical value.The negative effect of the content of active gases on the mechanical properties of the grown workpieces, established in this work, will allow to screen out powder with an unacceptable content of active gases ([N] ≥ 0.03 wt. %, or oxygen in [O] ≥ 0.02 wt. %) at the stage of incoming inspection.Keywords
This publication has 5 references indexed in Scilit:
- INFLUENCE OF ACTIVE GAS CONTENT IN POWDER ON MECHANICAL PROPERTIES OF WORKPIECE BLANKS PRODUCED BY PLASMA ADDITIVE TECHNOLOGIESNew Materials and Technologies in Metallurgy and Mechanical Engineering, 2025
- Study on the element segregation and Laves phase formation in the carbon nanotubes reinforced IN718 superalloy by laser claddingPowder Technology, 2019
- Influence of metal powder characteristics on product quality with directed energy deposition of Inconel 625CIRP Annals, 2016
- Effect of NiCrBSi content on microstructural evolution, cracking susceptibility and wear behaviors of laser cladding WC/Ni–NiCrBSi composite coatingsJournal of Alloys and Compounds, 2015
- influence of active gas content and disperse filler continuity on the process of bead formation in microplasma powder surfacing of nickel superalloysThe Paton Welding Journal, 2014