Sergey Chigileychik
Research Subjects
Sergey Chigileychik has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Kostyantyn Balushok
Motor Sich JSC
4 shared publications - Ruslan Kulykovskyi
Faculty of Engineering and Physics, National University Zaporizhzhia Polytechnic, 69063 Zaporizhzhia, Ukraine
3 shared publications - Игорь Андреевич Петрик
АТ «Мотор Січ», Запоріжжя
3 shared publications - Nataliia Shyrokobokova
National University Zaporizhzhia Polytechnic, Zaporizhzhia
2 shared publications - Sergey Sakhno
JSC «MOTOR SICH», Zaporizhzhia
2 shared publications - Yuriy Torba
SE “Ivchenko-Progress”, Zaporizhzhia, Ukraine
2 shared publications
Latest Publications
- Open Access
- 7 May 2026
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 2,p. 79-86
MICROPLASMA POWDER CLADDING FOR THE REPAIR OF TURBINE MONOWHEELS MADE OF NICKEL-BASED HEAT-RESISTANT ALLOYS
Purpose. Theoretical justification and experimental development of a technology for the restoration of turbine blades of an aircraft engine, manufactured using the “blisk” process from heat-resistant nickel alloys, via the additive micro-plasma powder cladding method (MPC). Research methods. The study employed microplasma layer-by-layer powder cladding on the end faces of plates made of the ЖС32-ВИ alloy, using the specialised robotic system STARWELD 190H. The MPC process was carried out using direct current of positive polarity (currents of 2…50 А). High-purity argon was used as the plasma-forming and shielding gas. The dimensions of the test plates were115×15×2 mm. The cladding was carried out using a reciprocating motion. After cladding, the samples were subjected to heat treatment. The mechanical properties of the samples obtained by the additive growth method were determined on standard flat specimens. Results. Following mechanical testing, the specimens exhibited the following properties: average tensile strength σ = 1147 MPa and plasticity δ = 9.5%, whilst the requirements of the standard specify σв ≥ 882 MPa and δ = 6.0%. The fracture surfaces exhibited a medium-grained structure. No defects were observed in the fracture surfaces. The microstructure of the sample material prior to heat treatment consists of γ-solid solution containing an intermetallic γ´ phase, carbides, carbonitrides, and 5 μm-sized eutectic (γ-γ´) phase, which is characteristic of the as-cast condition of the ЖС32-ВИ alloy. The microstructure of the sample material after heat treatment corresponds to the normal state of the ЖС32-ВИ alloy. Scientific novelty. When manufacturing turbine wheels by casting, one of the most serious problems is casting defects, such as cracks, porosity and cavities. The use of existing repair methods, which are based on welding or surfacing using argon arc welding, for example for blades, is limited by the high susceptibility of heat-resistant nickel alloys (ЖС3ДК, ВЖЛ12) to the formation of heat-fatigue cracks due to the high content of γ´ phase. The proposed repair technology involves cutting the blade down to the location of the defect and subsequently restoring the blade profile layer by layer using the additive micro-plasma cladding method. Practical value. It has been established that the repair of aircraft engine turbine blades using the additive microplasma powder cladding method ensures high mechanical properties across the entire height of the grown blade without the occurrence of casting defects.
- 7 May 2026
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 2,p. 79-86
Open AccessMICROPLASMA POWDER CLADDING FOR THE REPAIR OF TURBINE MONOWHEELS MADE OF NICKEL-BASED HEAT-RESISTANT ALLOYS
Purpose. Theoretical justification and experimental development of a technology for the restoration of turbine blades of an aircraft engine, manufactured using the “blisk” process from heat-resistant nickel alloys, via the additive micro-plasma powder cladding method (MPC). Research methods. The study employed microplasma layer-by-layer powder cladding on the end faces of plates made of the ЖС32-ВИ alloy, using the specialised robotic system STARWELD 190H. The MPC process was carried out using direct current of positive polarity (currents of 2…50 А). High-purity argon was used as the plasma-forming and shielding gas. The dimensions of the test plates were115×15×2 mm. The cladding was carried out using a reciprocating motion. After cladding, the samples were subjected to heat treatment. The mechanical properties of the samples obtained by the additive growth method were determined on standard flat specimens. Results. Following mechanical testing, the specimens exhibited the following properties: average tensile strength σ = 1147 MPa and plasticity δ = 9.5%, whilst the requirements of the standard specify σв ≥ 882 MPa and δ = 6.0%. The fracture surfaces exhibited a medium-grained structure. No defects were observed in the fracture surfaces. The microstructure of the sample material prior to heat treatment consists of γ-solid solution containing an intermetallic γ´ phase, carbides, carbonitrides, and 5 μm-sized eutectic (γ-γ´) phase, which is characteristic of the as-cast condition of the ЖС32-ВИ alloy. The microstructure of the sample material after heat treatment corresponds to the normal state of the ЖС32-ВИ alloy. Scientific novelty. When manufacturing turbine wheels by casting, one of the most serious problems is casting defects, such as cracks, porosity and cavities. The use of existing repair methods, which are based on welding or surfacing using argon arc welding, for example for blades, is limited by the high susceptibility of heat-resistant nickel alloys (ЖС3ДК, ВЖЛ12) to the formation of heat-fatigue cracks due to the high content of γ´ phase. The proposed repair technology involves cutting the blade down to the location of the defect and subsequently restoring the blade profile layer by layer using the additive micro-plasma cladding method. Practical value. It has been established that the repair of aircraft engine turbine blades using the additive microplasma powder cladding method ensures high mechanical properties across the entire height of the grown blade without the occurrence of casting defects.
- 9 November 2025
- Published by Springer Nature
- p. 415-419
Additive Manufacturing in the Production of Aircraft Parts
- 9 November 2025
- Published by Springer Nature
- p. 415-419
Additive Manufacturing in the Production of Aircraft Parts
- Open Access
- 19 June 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Visnik Nacional noi academii nauk Ukrai ni
- No. 6,p. 53-55
Науково-технічне співробітництво АТ «Івченко-Прогрес» та установ НАН України з питань оптимізації виготовлення деталей авіаційних двигунів. Досягнення та перспективи подальшої співпраці
Як цитувати: Чигілейчик С.Л. Науково-технічне співробітництво АТ «Івченко-Прогрес» та установ НАН України з питань оптимізації виготовлення деталей авіаційних двигунів. Досягнення та перспективи подальшої співпраці (стенограма виступу на сесії Загальних зборів НАН України 30 квітня 2025 р.). Вісник НАН України. 2025. № 6. С. 53—55. https://doi.org/10.15407/visn2025.06.053
- 19 June 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Visnik Nacional noi academii nauk Ukrai ni
- No. 6,p. 53-55
Open AccessНауково-технічне співробітництво АТ «Івченко-Прогрес» та установ НАН України з питань оптимізації виготовлення деталей авіаційних двигунів. Досягнення та перспективи подальшої співпраці
Як цитувати: Чигілейчик С.Л. Науково-технічне співробітництво АТ «Івченко-Прогрес» та установ НАН України з питань оптимізації виготовлення деталей авіаційних двигунів. Досягнення та перспективи подальшої співпраці (стенограма виступу на сесії Загальних зборів НАН України 30 квітня 2025 р.). Вісник НАН України. 2025. № 6. С. 53—55. https://doi.org/10.15407/visn2025.06.053
- Open Access
- 29 January 2025
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 4,p. 52-58
INFLUENCE OF ACTIVE GAS CONTENT IN POWDER ON MECHANICAL PROPERTIES OF WORKPIECE BLANKS PRODUCED BY PLASMA ADDITIVE TECHNOLOGIES
Purpose. Analysis of the influence of powder quality (content of active gases) on the level of mechanical properties of workpieces produced by plasma additive technologies. Research methods. Chemical composion of the powders was determined in accordance with regulatory document. The presence of non-metallic inclusions and contaminants in the powders was determined visualy. To quantify the oxygen in the powders, the vacuum extraction method was used in accordance with ДСТУ ISO 4491-4:2016. Oxygen and nitrogen gas analyser TC 500 (company LECO). Before being loaded into the dosing unit, all powders were dried in an oven (temperature - 250°C, for 1 hour). Samples (size 130×70×14 mm) were produced by additive growth by plasma powder surfacing (PPS) on a specialised robotic device STARWELD 190H. The chemical composition of the grown samples was determined by the spectral method using a SPECTROMAX optical emission spectrometer according to standard methods in accordance with ГОСТ19863.1-19863.12. The content of nitrogen and oxygen in the deposited metal was determined in accordance with TC 500 (company LECO). Microstructural analysis were carried out on the samples in the longitudinal and cross directions before and after heat treatment, after etching in a reagent for electrowinning of heat-resistant alloys (Н3РО4 – 800 ml +CrО3 – 100ml). The mechanical properties of the alloy were obtained on standard cylindrical samples according to ГОСТ 1497-84, ГОСТ 1497-84, ГОСТ 10145-81s. Results. The chemical composition of the deposited metal is determined by the chemical composition of the powder. The content of oxygen and nitrogen in the deposited metal is determined by the content of these elements in the powder itself, as well as by the protection of the weld pool with argon. It has been established that in the alloy ЭП-648ВИ when the powder contains nitrogen in the amount of [N] ≥ 0.03 wt. %, or oxygen in [O] ≥ 0.02 wt. % in the deposited metal at a temperature of 1100 °C, a significant decrease in its deformation capacity (ε ≤ 3.8 %) is recorded, which under the influence of thermal stresses leads to the appearance of hot cracks, and as a result, we see a significant decrease in the strength and plasticity in the longitudinal direction. Scientific novelty. The influence of the quality of the alloy ЕП-648ВИ powder on the properties of workpieces obtained using additive technologies has been established. Practical value.The negative effect of the content of active gases on the mechanical properties of the grown workpieces, established in this work, will allow to screen out powder with an unacceptable content of active gases ([N] ≥ 0.03 wt. %, or oxygen in [O] ≥ 0.02 wt. %) at the stage of incoming inspection.
- 29 January 2025
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 4,p. 52-58
Open AccessINFLUENCE OF ACTIVE GAS CONTENT IN POWDER ON MECHANICAL PROPERTIES OF WORKPIECE BLANKS PRODUCED BY PLASMA ADDITIVE TECHNOLOGIES
Purpose. Analysis of the influence of powder quality (content of active gases) on the level of mechanical properties of workpieces produced by plasma additive technologies. Research methods. Chemical composion of the powders was determined in accordance with regulatory document. The presence of non-metallic inclusions and contaminants in the powders was determined visualy. To quantify the oxygen in the powders, the vacuum extraction method was used in accordance with ДСТУ ISO 4491-4:2016. Oxygen and nitrogen gas analyser TC 500 (company LECO). Before being loaded into the dosing unit, all powders were dried in an oven (temperature - 250°C, for 1 hour). Samples (size 130×70×14 mm) were produced by additive growth by plasma powder surfacing (PPS) on a specialised robotic device STARWELD 190H. The chemical composition of the grown samples was determined by the spectral method using a SPECTROMAX optical emission spectrometer according to standard methods in accordance with ГОСТ19863.1-19863.12. The content of nitrogen and oxygen in the deposited metal was determined in accordance with TC 500 (company LECO). Microstructural analysis were carried out on the samples in the longitudinal and cross directions before and after heat treatment, after etching in a reagent for electrowinning of heat-resistant alloys (Н3РО4 – 800 ml +CrО3 – 100ml). The mechanical properties of the alloy were obtained on standard cylindrical samples according to ГОСТ 1497-84, ГОСТ 1497-84, ГОСТ 10145-81s. Results. The chemical composition of the deposited metal is determined by the chemical composition of the powder. The content of oxygen and nitrogen in the deposited metal is determined by the content of these elements in the powder itself, as well as by the protection of the weld pool with argon. It has been established that in the alloy ЭП-648ВИ when the powder contains nitrogen in the amount of [N] ≥ 0.03 wt. %, or oxygen in [O] ≥ 0.02 wt. % in the deposited metal at a temperature of 1100 °C, a significant decrease in its deformation capacity (ε ≤ 3.8 %) is recorded, which under the influence of thermal stresses leads to the appearance of hot cracks, and as a result, we see a significant decrease in the strength and plasticity in the longitudinal direction. Scientific novelty. The influence of the quality of the alloy ЕП-648ВИ powder on the properties of workpieces obtained using additive technologies has been established. Practical value.The negative effect of the content of active gases on the mechanical properties of the grown workpieces, established in this work, will allow to screen out powder with an unacceptable content of active gases ([N] ≥ 0.03 wt. %, or oxygen in [O] ≥ 0.02 wt. %) at the stage of incoming inspection.
- Open Access
- 21 November 2024
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 6,p. 47-51
Сфера застосування адитивних технологій методом плазмового наплавлення при виробництві авіаційних двигунів
The determination of the scope of application of additive technologies by the method of plasma surfacing in the manufacture of aircraft engines is determined by ensuring the mechanical and service properties of heat-resistant nickel and titanium alloys during the production of blanks, necessary for the operation and determination of the technological capabilities of this method. To determine the mechanical properties, 140×70×14 mm heat-resistant nickel alloys ЭП 648ВИ, ВЖ 98ВИ and titanium alloys ВТ6, ВТ20 were grown. After growing, all samples underwent heat treatment according to the technical conditions for each alloy. The mechanical properties for ЭП 648ВИ were determined on these samples (transverse direction: σВ=83.5 kgf/mm2; σ0.2= 63.5 kgf/mm2; δ= 11.2 %; ψ = 21.8 %; longitudinal direction: σB=87.5 kgf/mm2; σ0.2= 57.3 kgf/mm2; δ=21.8 %; ψ= 23.5 %), for ВЖ98 (transverse direction: σВ=83.5 kgf/mm2; σ0.2= 63.5 kgf/mm2; δ= 11.2 %; ψ= 21.8 %, longitudinal direction: σВ=87.5 kgf/mm2; σ0.2= 57.3 kgf/mm2; δ=21.8 %; ψ= 23.5 %), for ВТ6 (transverse direction: σВ=92.2 kgf/mm2 σ0.2= 84.8 kgf/mm2; δ= 17.2 %; ψ= 54.3 %; longitudinal direction: σВ=98.9 кгс/мм2; σ0.2= 91.0 кгс/мм2; δ=9.8 %; ψ= 22.5 %), for ВТ20 (transverse direction: σВ= 115 kgf/mm2; σ0.2= 108 kgf/mm2; δ=15 %; ψ=29.3 %; longitudinal direction: σВ=114 kgf/mm2; σ0.2= 103 kgf/mm2; δ= 14.0 %; ψ=37.6 %). The obtained properties of heat-resistant nickel and titanium alloys are not inferior to blanks obtained by casting and forging methods. The scope of application of additive technologies by the method of plasma surfacing in the manufacture of aircraft engines is defined. For heat-resistant nickel alloys, these are parts included in nozzle devices, heat pipes and combustion chambers. For titanium alloys, these are parts included in the body. From the technological possibilities, the plasma surfacing method is most rationally used when growing cylindrical and conical workpieces of parts with a diameter of 150 to 1500 mm. The technology of adaptive plasma cultivation has been introduced into serial production at JSC "Motor Sich". Currently, more than 20 different types of aircraft engine parts are being produced.
- 21 November 2024
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 6,p. 47-51
Open AccessСфера застосування адитивних технологій методом плазмового наплавлення при виробництві авіаційних двигунів
The determination of the scope of application of additive technologies by the method of plasma surfacing in the manufacture of aircraft engines is determined by ensuring the mechanical and service properties of heat-resistant nickel and titanium alloys during the production of blanks, necessary for the operation and determination of the technological capabilities of this method. To determine the mechanical properties, 140×70×14 mm heat-resistant nickel alloys ЭП 648ВИ, ВЖ 98ВИ and titanium alloys ВТ6, ВТ20 were grown. After growing, all samples underwent heat treatment according to the technical conditions for each alloy. The mechanical properties for ЭП 648ВИ were determined on these samples (transverse direction: σВ=83.5 kgf/mm2; σ0.2= 63.5 kgf/mm2; δ= 11.2 %; ψ = 21.8 %; longitudinal direction: σB=87.5 kgf/mm2; σ0.2= 57.3 kgf/mm2; δ=21.8 %; ψ= 23.5 %), for ВЖ98 (transverse direction: σВ=83.5 kgf/mm2; σ0.2= 63.5 kgf/mm2; δ= 11.2 %; ψ= 21.8 %, longitudinal direction: σВ=87.5 kgf/mm2; σ0.2= 57.3 kgf/mm2; δ=21.8 %; ψ= 23.5 %), for ВТ6 (transverse direction: σВ=92.2 kgf/mm2 σ0.2= 84.8 kgf/mm2; δ= 17.2 %; ψ= 54.3 %; longitudinal direction: σВ=98.9 кгс/мм2; σ0.2= 91.0 кгс/мм2; δ=9.8 %; ψ= 22.5 %), for ВТ20 (transverse direction: σВ= 115 kgf/mm2; σ0.2= 108 kgf/mm2; δ=15 %; ψ=29.3 %; longitudinal direction: σВ=114 kgf/mm2; σ0.2= 103 kgf/mm2; δ= 14.0 %; ψ=37.6 %). The obtained properties of heat-resistant nickel and titanium alloys are not inferior to blanks obtained by casting and forging methods. The scope of application of additive technologies by the method of plasma surfacing in the manufacture of aircraft engines is defined. For heat-resistant nickel alloys, these are parts included in nozzle devices, heat pipes and combustion chambers. For titanium alloys, these are parts included in the body. From the technological possibilities, the plasma surfacing method is most rationally used when growing cylindrical and conical workpieces of parts with a diameter of 150 to 1500 mm. The technology of adaptive plasma cultivation has been introduced into serial production at JSC "Motor Sich". Currently, more than 20 different types of aircraft engine parts are being produced.
- Open Access
- 31 October 2024
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 3,p. 25-30
DETERMINATION OF OPTIMAL CONDITIONS FOR HERMETIC WELDING OF THIN FOILS WHEN USED IN MEMBRANE-TYPE STRUCTURES
Purpose. Development of optimal technology for welding thin-walled shells mode of 12Х18Н10Т steel (δ=0.15 mm), working at alternating loads. Research methods. Research methods. For welding automatic argon-arc welding (AAAW) equipment was used for of orbital welding, which includes a MW 2600 current source (FRONIUS) with software control unit and welding head of closed type MW40. Research warks showed that this type of welding is not enough for such small thicknesses concentration of the welding arc, which does not allow stable forming of the bath and obtaining solid uniform seam. A special robotic complex was used for microplasma welding STARWELD 190H, which includes: a power source for the regular arc INV 50; source main arc power supply INV 190; SIEMENS Simatic S 7-300 control unit; robot CR3-535M (MITSUBISHI); manipulator and HPH 80 plasmatron. Welding quality control was carried out by visual inspection and metallographic examination. Taking into account the conditions of operation of the parts, according to the technical conditions of the drawing, it was also provided pneumohydraulic control method. Obtained results. Visual inspection the outer surface of the welds showed the absence of defects in the form of pores, cracks, shells, no fusions, undercuts, etc. The geometric dimensions of the weld met the requirements of the standard documentation valid at the enterprise. Metallographic studies of the boxes membranes, welded by microplasma welding, gave a positive result. Defects of metallurgical character were not found in the welds. Practical value. The optimal method of welding that can be applied is determined for the manufacture of thin-walled membrane structures, from the point of view of manufacturability and economy expediency It has been established that microplasma welding allows obtaining a hermetically tight seam, when the thickness of parts to be welded is about 0.15 mm. The performance of welded membrane boxes is confirmed in the barostatic valve of an aircraft engine. It is established that micro plasma welding can be used in the manufacture of thin-walled shells made of 12X18H10T steel (δ=0.15 mm), which work at variable loads. The technological process of welding is introduced into the series production.
- 31 October 2024
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 3,p. 25-30
Open AccessDETERMINATION OF OPTIMAL CONDITIONS FOR HERMETIC WELDING OF THIN FOILS WHEN USED IN MEMBRANE-TYPE STRUCTURES
Purpose. Development of optimal technology for welding thin-walled shells mode of 12Х18Н10Т steel (δ=0.15 mm), working at alternating loads. Research methods. Research methods. For welding automatic argon-arc welding (AAAW) equipment was used for of orbital welding, which includes a MW 2600 current source (FRONIUS) with software control unit and welding head of closed type MW40. Research warks showed that this type of welding is not enough for such small thicknesses concentration of the welding arc, which does not allow stable forming of the bath and obtaining solid uniform seam. A special robotic complex was used for microplasma welding STARWELD 190H, which includes: a power source for the regular arc INV 50; source main arc power supply INV 190; SIEMENS Simatic S 7-300 control unit; robot CR3-535M (MITSUBISHI); manipulator and HPH 80 plasmatron. Welding quality control was carried out by visual inspection and metallographic examination. Taking into account the conditions of operation of the parts, according to the technical conditions of the drawing, it was also provided pneumohydraulic control method. Obtained results. Visual inspection the outer surface of the welds showed the absence of defects in the form of pores, cracks, shells, no fusions, undercuts, etc. The geometric dimensions of the weld met the requirements of the standard documentation valid at the enterprise. Metallographic studies of the boxes membranes, welded by microplasma welding, gave a positive result. Defects of metallurgical character were not found in the welds. Practical value. The optimal method of welding that can be applied is determined for the manufacture of thin-walled membrane structures, from the point of view of manufacturability and economy expediency It has been established that microplasma welding allows obtaining a hermetically tight seam, when the thickness of parts to be welded is about 0.15 mm. The performance of welded membrane boxes is confirmed in the barostatic valve of an aircraft engine. It is established that micro plasma welding can be used in the manufacture of thin-walled shells made of 12X18H10T steel (δ=0.15 mm), which work at variable loads. The technological process of welding is introduced into the series production.
- Open Access
- 25 October 2024
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 5,p. 39-45
Ремонт деталей авіаційних двигунів із жароміцних нікелевих сплавів із застосуванням адитивних плазмових технологій
In order to improve the maintainability of aircraft engine parts, the article examined the use of additive technologies in repairs. The article establishes that the use of additive technologies by the method of plasma surfacing in the repair of aircraft engine parts, such as turbine blades, sealing discs, NA parts, is very promising and will significantly increase the percentage of parts and assemblies restored after operation, which have a significant area of damage. Turbine blades are made of nickel heat-resistant alloys with a polycrystalline structure (ЖС6К-ВИ, ЖС6У-ВИ), or from alloys with directional crystallization (ЖС32-ВИ, ЖС26-ВИ). After operating for more than 6 thousand hours, in addition to the operational wear of the ends and side walls of the shroud flanges, thermal fatigue cracks up to 6 mm deep are observed on the blades received for repair. The technology of argon-arc surfacing and the surfacing materials existing for this process do not provide the heat-resistant properties of the restored surface necessary for the operation of the blades. The solution to the problem was achieved through the use of a compressed arc source with precision adjustment of the welding current and mechanization of the supply of filler material (powder), which would make it possible to surfacing with a limited penetration depth and, accordingly, mixing the deposited material with the base metal. The developed technology made it possible to restore damaged sections of blades after operation (shroud flanges, labyrinth scallops, z-shaped profiles and airfoil ends) on heat-resistant alloys using filler material equal to the strength of the base metal. For this process, powders of nickel and cobalt alloys with a fraction of +63...-160 microns are used, obtained by atomization with a jet of inert gas (argon). The main powders used are ЖС32-ВИ, ЖС6К-ВИ, В3К, Stellite 12, Stellite 6, ХТН61. Disc material – ЭП742-ИД. Working medium, air, oil and combustion products. The maximum heating temperature of labyrinth scallops is up to 680 ºC at a maximum medium pressure of up to 1.47 MPa. The maximum peripheral speed of the scallop end is 251 m/s. Material of seal mating parts ЭИ435 (cell δ = 0,1 mm). When developing the technology, the successful experience of restoring labyrinthine scallops of turbine blades was taken into account. The restoration of the labyrinthine ridges of the disk was carried out using a compressed arc source with precision control of the welding current and a robotic installation, which included a robot for moving the plasma torch and a manipulator for rotating the disk. This made it possible to carry out surfacing with a limited penetration depth and obtain a uniformly directed bead over the entire diameter of the disk. Testing of the restored disk in order to verify its performance was carried out as part of a run-in aircraft engine. To do this, after the next assembly of the run-in engine, the disk was installed in the MPT rotor. The test was carried out in 5 cycles, the duration of each cycle was 15 hours. No wear of the labyrinth ridges or cracks was detected. The functionality of the restored disk has been confirmed. NA parts are made of heat-resistant, low-aging, high-chromium nickel-based alloy ЭП648-ВИ. They operate in hot engine conditions at temperatures up to 900'C. As a result of operation, both end surfaces and flat surfaces in the tract area are subject to wear. To restore parts of the NA, the technology of additive growth by the method of microplasma powder surfacing was used. To confirm the operability of restored parts, a set of studies of samples grown using the same repair technology was conducted. At the same time, it was established that the chemical composition of the deposited metal corresponds to the requirements of the technical conditions-» the microstructure of the deposited metal after heat treatment corresponds to the normal heat-treated state of the alloy ЭП648-ВИ (ХН50ВМТЮБ-ВИ), the level of mechanical properties of the grown alloy with subsequent serial heat treatment (aging at 700ºC, exposure -16 hours) is not lower than the forging level used in serial production of the part.
- 25 October 2024
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 5,p. 39-45
Open AccessРемонт деталей авіаційних двигунів із жароміцних нікелевих сплавів із застосуванням адитивних плазмових технологій
In order to improve the maintainability of aircraft engine parts, the article examined the use of additive technologies in repairs. The article establishes that the use of additive technologies by the method of plasma surfacing in the repair of aircraft engine parts, such as turbine blades, sealing discs, NA parts, is very promising and will significantly increase the percentage of parts and assemblies restored after operation, which have a significant area of damage. Turbine blades are made of nickel heat-resistant alloys with a polycrystalline structure (ЖС6К-ВИ, ЖС6У-ВИ), or from alloys with directional crystallization (ЖС32-ВИ, ЖС26-ВИ). After operating for more than 6 thousand hours, in addition to the operational wear of the ends and side walls of the shroud flanges, thermal fatigue cracks up to 6 mm deep are observed on the blades received for repair. The technology of argon-arc surfacing and the surfacing materials existing for this process do not provide the heat-resistant properties of the restored surface necessary for the operation of the blades. The solution to the problem was achieved through the use of a compressed arc source with precision adjustment of the welding current and mechanization of the supply of filler material (powder), which would make it possible to surfacing with a limited penetration depth and, accordingly, mixing the deposited material with the base metal. The developed technology made it possible to restore damaged sections of blades after operation (shroud flanges, labyrinth scallops, z-shaped profiles and airfoil ends) on heat-resistant alloys using filler material equal to the strength of the base metal. For this process, powders of nickel and cobalt alloys with a fraction of +63...-160 microns are used, obtained by atomization with a jet of inert gas (argon). The main powders used are ЖС32-ВИ, ЖС6К-ВИ, В3К, Stellite 12, Stellite 6, ХТН61. Disc material – ЭП742-ИД. Working medium, air, oil and combustion products. The maximum heating temperature of labyrinth scallops is up to 680 ºC at a maximum medium pressure of up to 1.47 MPa. The maximum peripheral speed of the scallop end is 251 m/s. Material of seal mating parts ЭИ435 (cell δ = 0,1 mm). When developing the technology, the successful experience of restoring labyrinthine scallops of turbine blades was taken into account. The restoration of the labyrinthine ridges of the disk was carried out using a compressed arc source with precision control of the welding current and a robotic installation, which included a robot for moving the plasma torch and a manipulator for rotating the disk. This made it possible to carry out surfacing with a limited penetration depth and obtain a uniformly directed bead over the entire diameter of the disk. Testing of the restored disk in order to verify its performance was carried out as part of a run-in aircraft engine. To do this, after the next assembly of the run-in engine, the disk was installed in the MPT rotor. The test was carried out in 5 cycles, the duration of each cycle was 15 hours. No wear of the labyrinth ridges or cracks was detected. The functionality of the restored disk has been confirmed. NA parts are made of heat-resistant, low-aging, high-chromium nickel-based alloy ЭП648-ВИ. They operate in hot engine conditions at temperatures up to 900'C. As a result of operation, both end surfaces and flat surfaces in the tract area are subject to wear. To restore parts of the NA, the technology of additive growth by the method of microplasma powder surfacing was used. To confirm the operability of restored parts, a set of studies of samples grown using the same repair technology was conducted. At the same time, it was established that the chemical composition of the deposited metal corresponds to the requirements of the technical conditions-» the microstructure of the deposited metal after heat treatment corresponds to the normal heat-treated state of the alloy ЭП648-ВИ (ХН50ВМТЮБ-ВИ), the level of mechanical properties of the grown alloy with subsequent serial heat treatment (aging at 700ºC, exposure -16 hours) is not lower than the forging level used in serial production of the part.
- Open Access
- 10 June 2024
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Mechanics and Advanced Technologies
- Vol. 8 (2(101)) , 121-129
Developing technology of directed energy deposition of workpieces of parts of aircraft engines from heat-resistant nickel alloys by means of using layer-by-layer microplasma surfacing method
The article presents the technology of the Directed Energy Deposition (DED) process using the method of layer-by-layer microplasma surfacing with powder and wire made from a heat-resistant nickel-based high-chromium alloy of the Ni-Cr-Ti-Al system (γ´ = 3–5 %), which is used for manufacturing workpieces of gas turbine engine parts, while ensuring a given level of mechanical properties required for the parts’ further operation. The article discusses the equipment and characteristic features of the DED technology using the continuous (layer-by-layer) microplasma surfacing method. The additive deposition was implemented on the STARWELD 190H robotic installation for microplasma powder surfacing and on the integrated installation based on the FANUC robot and the SBI plasma equipment by means of using wire made from a nickel-based alloy of the Ni-Cr-Ti-Al system (γ´ = 3–5 %). Following the deposition, such operations as the heat treatment (aging 900 °С, exposure 16 hours), the machining and the quality control were conducted. A set of studies was conducted to develop the evidence base for the purpose of determining the possibility of installing deposited workpieces in engines, with the studies being as follows: determining the chemical composition of workpieces deposited by means of a technology similar to depositing workpieces; implementing metallographic studies and mechanical tests. The authors state that studies conducted showed that the chemical composition of the deposited metal is in compliance with the requirements set forth in the regulatory documentation, and the microstructure of the deposited metal after the heat treatment corresponds to the normally heat-treated state of a low-aging nickel-based high-chromium alloy of the Ni-Cr-Ti-Al system (γ´ = 3–5 %),while the level of mechani-cal properties of the deposited alloy followed by the serial heat treatment (aging 900 °С, holding for 16 hours) is not lower than the level of the forging implemented in the serial production of this type of parts.
- 10 June 2024
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Mechanics and Advanced Technologies
- Vol. 8 (2(101)) , 121-129
Open AccessDeveloping technology of directed energy deposition of workpieces of parts of aircraft engines from heat-resistant nickel alloys by means of using layer-by-layer microplasma surfacing method
The article presents the technology of the Directed Energy Deposition (DED) process using the method of layer-by-layer microplasma surfacing with powder and wire made from a heat-resistant nickel-based high-chromium alloy of the Ni-Cr-Ti-Al system (γ´ = 3–5 %), which is used for manufacturing workpieces of gas turbine engine parts, while ensuring a given level of mechanical properties required for the parts’ further operation. The article discusses the equipment and characteristic features of the DED technology using the continuous (layer-by-layer) microplasma surfacing method. The additive deposition was implemented on the STARWELD 190H robotic installation for microplasma powder surfacing and on the integrated installation based on the FANUC robot and the SBI plasma equipment by means of using wire made from a nickel-based alloy of the Ni-Cr-Ti-Al system (γ´ = 3–5 %). Following the deposition, such operations as the heat treatment (aging 900 °С, exposure 16 hours), the machining and the quality control were conducted. A set of studies was conducted to develop the evidence base for the purpose of determining the possibility of installing deposited workpieces in engines, with the studies being as follows: determining the chemical composition of workpieces deposited by means of a technology similar to depositing workpieces; implementing metallographic studies and mechanical tests. The authors state that studies conducted showed that the chemical composition of the deposited metal is in compliance with the requirements set forth in the regulatory documentation, and the microstructure of the deposited metal after the heat treatment corresponds to the normally heat-treated state of a low-aging nickel-based high-chromium alloy of the Ni-Cr-Ti-Al system (γ´ = 3–5 %),while the level of mechani-cal properties of the deposited alloy followed by the serial heat treatment (aging 900 °С, holding for 16 hours) is not lower than the level of the forging implemented in the serial production of this type of parts.
- 18 July 2022
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Kosmìčna nauka ì tehnologìâ
- Vol. 28 (3) , 03-16
RESEARCH AND OPTIMIZATION OF REFURBISHMENT OF HPT BLADES OF THE D-18T AIRCRAFT GAS TURBINE ENGINE BY MICRO-PLASMA POWDER WELDING
In current work, peculiarities of the micro-plasma powder welding deposition process applied to the batch refurbishment of D-18T aircraft engine HPT blades made of ZhS32-VI nickel superalloy with limited weldability have been studied. It has been demonstrated that extending operating resource over 6-8 thousand hours leads to an increase in ZhS32-VI “base-deposited metal” weld’s cracking susceptibility during welding and subsequent thermal processing operations. It has been shown that providing stable forming of deposited bead on the shroud edge’s surface requires applying nonstationary impulse modes of straight polarity welding current. Considering the significant amount of technological parameters of the process studied, subjective analysis of such welding modes is extremely complicated. We have introduced the method of specifying requirements for such single-layer micro-plasma powder welding deposition modes with welding current in a range of 7-20 A according to the criteria of effective arc heating power and heat input, which involves using the system for registration and digital processing of welding current-welding bead deposition time dependency. Based on the analysis of statistical data on the quantitative evaluation of cracking susceptibility of the investigated weld, the optimal range of average values has been discovered for these generalized welding deposition mode parameters to be applied in a manual or automated process, which provides no more than several percent of cracked blades detected at the end of refurbishment technological cycle. We have shown that significant technological parameters, which affect the amount of technological defects during mentioned blades’ refurbishment, are the average value of effective welding current and ZhS32 superalloy powder quality, primarily determined by oxygen and nitrogen average weight content in its dispersed particles. It was also shown that the increase in average weight content of gas impurities in the filler powder, primarily oxygen, causes a significant increase in energy consumed on deposited bead formation during the micro-plasma powder deposition process. An initial quality control method for the ZhS32-VI filler powder range has been proposed. The method is based on the average weight content of oxygen and nitrogen, evaluated by reducing fusion in transporting gas flow and on evaluation criteria of effective arc heating power and heat input average values of witness sample blades’ refurbishment process and their conformity to previously defined optimal. An evaluation of future application possibilities for registration systems and deposition mode analysis in batch repair conditions of nickel superalloy aircraft parts has been introduced.
- 18 July 2022
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Kosmìčna nauka ì tehnologìâ
- Vol. 28 (3) , 03-16
RESEARCH AND OPTIMIZATION OF REFURBISHMENT OF HPT BLADES OF THE D-18T AIRCRAFT GAS TURBINE ENGINE BY MICRO-PLASMA POWDER WELDING
In current work, peculiarities of the micro-plasma powder welding deposition process applied to the batch refurbishment of D-18T aircraft engine HPT blades made of ZhS32-VI nickel superalloy with limited weldability have been studied. It has been demonstrated that extending operating resource over 6-8 thousand hours leads to an increase in ZhS32-VI “base-deposited metal” weld’s cracking susceptibility during welding and subsequent thermal processing operations. It has been shown that providing stable forming of deposited bead on the shroud edge’s surface requires applying nonstationary impulse modes of straight polarity welding current. Considering the significant amount of technological parameters of the process studied, subjective analysis of such welding modes is extremely complicated. We have introduced the method of specifying requirements for such single-layer micro-plasma powder welding deposition modes with welding current in a range of 7-20 A according to the criteria of effective arc heating power and heat input, which involves using the system for registration and digital processing of welding current-welding bead deposition time dependency. Based on the analysis of statistical data on the quantitative evaluation of cracking susceptibility of the investigated weld, the optimal range of average values has been discovered for these generalized welding deposition mode parameters to be applied in a manual or automated process, which provides no more than several percent of cracked blades detected at the end of refurbishment technological cycle. We have shown that significant technological parameters, which affect the amount of technological defects during mentioned blades’ refurbishment, are the average value of effective welding current and ZhS32 superalloy powder quality, primarily determined by oxygen and nitrogen average weight content in its dispersed particles. It was also shown that the increase in average weight content of gas impurities in the filler powder, primarily oxygen, causes a significant increase in energy consumed on deposited bead formation during the micro-plasma powder deposition process. An initial quality control method for the ZhS32-VI filler powder range has been proposed. The method is based on the average weight content of oxygen and nitrogen, evaluated by reducing fusion in transporting gas flow and on evaluation criteria of effective arc heating power and heat input average values of witness sample blades’ refurbishment process and their conformity to previously defined optimal. An evaluation of future application possibilities for registration systems and deposition mode analysis in batch repair conditions of nickel superalloy aircraft parts has been introduced.
- 24 February 2022
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 1,p. 57-63
Досвід впровадження адитивних технологій при ремонті деталей ГТД зі сплава ЕП 648 ВІ (ХН50ВМТЮБ-ВІ) в умовах серійного виробництва
Technology has been developed for repairing the nozzle assembly (SA) casing in the D-18T engine by additively growing the damaged part by microplasma surfacing with a powder of EP648VI (KhN50VMTYUB-VI) alloy. Traditionally, a part with such damage was rejected. The cost of replacing a damaged part with a new one is about 200 thousand hryvnias. The article discusses the equipment and features of the growing technology using the method of microplasma multilayer surfacing. Additive growth of the cut-damaged part was carried out on a STARWELD 190 H robotic installation for microplasma powder surfacing using EP648 VI alloy powders with a 63–163 micron fraction. After growing, heat treatment (aging at 700 ºС, exposure for 16 hours), mechanical processing, and quality control of the grown part were carried out. To create an evidence base to determine the possibility of installing a repaired part on the engine, a set of studies was carried out, which included the determination of the chemical composition of samples grown using a technology similar to repair, metallographic studies, and mechanical tests. As a result, it was found that the chemical composition of the deposited metal meets the requirements of the technical specifications TU 14-1-3046-97 "Bars made of heat-resistant alloy grade KhN50VMTYUB (EP648), and the microstructure of the deposited metal after heat treatment is a γ - solid solution with the presence of carbides, carbonitrides and a small amount of γ´ phase, which corresponds to the normally heat-treated state of the EP 648 VI (KhN50VMTYUB-VI) alloy and the level of mechanical properties of the grown alloy with subsequent serial heat treatment (aging at 700 ° C, holding for 16 hours) not lower than the level of the forging used at serial production of a part. The economic effect of the introduction of this technology is shown, which is more than 100 thousand hryvnias (about 23% of the cost of a new part).
- 24 February 2022
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 1,p. 57-63
Досвід впровадження адитивних технологій при ремонті деталей ГТД зі сплава ЕП 648 ВІ (ХН50ВМТЮБ-ВІ) в умовах серійного виробництва
Technology has been developed for repairing the nozzle assembly (SA) casing in the D-18T engine by additively growing the damaged part by microplasma surfacing with a powder of EP648VI (KhN50VMTYUB-VI) alloy. Traditionally, a part with such damage was rejected. The cost of replacing a damaged part with a new one is about 200 thousand hryvnias. The article discusses the equipment and features of the growing technology using the method of microplasma multilayer surfacing. Additive growth of the cut-damaged part was carried out on a STARWELD 190 H robotic installation for microplasma powder surfacing using EP648 VI alloy powders with a 63–163 micron fraction. After growing, heat treatment (aging at 700 ºС, exposure for 16 hours), mechanical processing, and quality control of the grown part were carried out. To create an evidence base to determine the possibility of installing a repaired part on the engine, a set of studies was carried out, which included the determination of the chemical composition of samples grown using a technology similar to repair, metallographic studies, and mechanical tests. As a result, it was found that the chemical composition of the deposited metal meets the requirements of the technical specifications TU 14-1-3046-97 "Bars made of heat-resistant alloy grade KhN50VMTYUB (EP648), and the microstructure of the deposited metal after heat treatment is a γ - solid solution with the presence of carbides, carbonitrides and a small amount of γ´ phase, which corresponds to the normally heat-treated state of the EP 648 VI (KhN50VMTYUB-VI) alloy and the level of mechanical properties of the grown alloy with subsequent serial heat treatment (aging at 700 ° C, holding for 16 hours) not lower than the level of the forging used at serial production of a part. The economic effect of the introduction of this technology is shown, which is more than 100 thousand hryvnias (about 23% of the cost of a new part).