Physico-Chemical Features of Producing High-Temperature Strength Niobium Nb-Ti-Al-Cr-Mo System Alloys by Melting and the Powder Metallurgy Method
Open Access
- 1 January 2026
- journal article
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 33 (3-4) , 87-98
Abstract
Niobium alloys of the Nb-Ti-Al system are one of the most promising alloys in the rocket and space industry, especially alloys with a low specific gravity (≤ 7g/cm3), which have a yield strength at 1000 °C of not less than 500 MPa. Our studies have established the possibility of creating promising cast heat-resistant alloys of this system, and a promising heat-resistant alloy 57Nb-10Cr-5Al-21Ti-7Mo (at. %), which meets the specified requirements, was also developed. However, the large crystallization interval of cast alloys of this system, the thermophysical features of their crystallization cause the possibility of the formation of dendritic structures, the development of dendritic liquation and segregation, and the tendency to the formation of crystallization cracks, which reduces the operational characteristics of cast alloys. In this regard, there was a need to investigate the possibilities of obtaining these alloys by the powder metallurgy method. The article presents the results of a study of the influence of the production technology and the main technological parameters on the structural features and mechanical properties of the promising heat-resistant alloy 57Nb-10Cr-5Al-21Ti-7Mo (%, at.), obtained by the melting method and by two promising powder metallurgy technological schemes. The possibility of obtaining a homogeneous fine-crystalline alloy 57Nb-10Cr-5Al-21Ti-7Mo (at. %) with strength equal to that of the cast alloy by the powder metallurgy method using both open hot forging of billets from a mixture of powders at a temperature of 1200 °C with annealing at 1600 °C in vacuum (the first technological scheme), and the second vacuum-technological scheme – after sintering at 1600 °C of billets from a mixture of powders and thermoplastic compression deformation in vacuum has been established. The use of hot thermomechanical processing of sintered blanks at relatively low temperatures (1200 °C) in the range of solid-phase reactions provides materials with high dispersion of the structure and a high degree of homogeneity. The possibility of creating a composite material, the regularities of its dissolution during the annealing process, which allow controlling the processes of porosity formation and grain sizes of the alloy (57Nb-21Ti-5Al-10Cr-7Mo) at. % when obtained by the powder metallurgy method, is shown. Ніобієві сплави системи Nb-Ti-Al є одними з найбільш перспективних сплавів ракетно-космічної сфери, особливо сплави з низькою питомою вагою (≤ 7г/см3), що мають межу плинності при 1000 °С не нижче 500 МПа. У наших дослідженнях була встановлена можливість створення перспективних литих жароміцних сплавів даної системи, а також був розроблений перспективний жароміцний сплав 57Nb-10Cr-5Al-21Ti-7Mo (ат. %), який відповідає вказаним вимогам. Проте великий інтервал кристалізації литих сплавів даної системи, теплофізичні особливості їх кристалізації спричиняють можливість утворення дендритних структур, розвиток дендритної ліквації та сегрегації, схильність до утворення кристалізаційних тріщин, що знижує експлуатаційні характеристики литих сплавів. У зв’язку з цим, виникла необхідність дослідити можливості отримання даних сплавів методом порошкової металургії. В статті наведено результати дослідження впливу технології отримання та основних технологічних параметрів на особливості структури та механічні властивості перспективного жароміцного сплаву 57Nb-10Cr-5Al-21Ti-7Mo (%, ат.), отриманого методом плавки та по двох перспективних технологічних схемах порошкової металургії. Встановлено можливість одержання гомогенного дрібнокристалічного сплаву 57Nb-10Cr-5Al-21Ti-7Mo (ат. %) з міцністю нарівні показників литого сплаву методом порошкової металургії з використанням як відкритого гарячого штампування заготовок із суміші порошків при температурі 1200 °С з відпалом при 1600 °С у вакуумі (перша технологічна схема), так і при другій вакуумно-технологічній схемі — після спікання при 1600 °С заготовок із суміші порошків і термопластичної деформації на стиск у вакуумі. Застосування гарячої термомеханічної обробки спечених заготовок при відносно низьких температурах (1200 °С) в діапазоні твердофазних реакцій забезпечує отримання матеріалів з високою дисперсністю структури та високим ступенем гомогенності. Показано можливість створення композиційного матеріалу, закономірності його...Keywords
This publication has 18 references indexed in Scilit:
- Effect of the Production Parameters on Structural Features and Mechanical Properties of Multicomponent Creep-Resistant Niobium-Based AlloyPowder Metallurgy and Metal Ceramics, 2024
- Powder production, FAST processing and properties of a Nb-silicide based alloy for high temperature aerospace applicationsJournal of Materials Research and Technology, 2023
- Influence of Hot Forging on the Elastic Properties and Character of Anisotropy of Powder Composites with Titanium MatrixMaterials Science, 2021
- High-Entropy Alloys2019
- High-entropy alloy: challenges and prospectsMaterials Today, 2016
- Mechanical properties of low-density, refractory multi-principal element alloys of the Cr–Nb–Ti–V–Zr systemMaterials Science and Engineering: A, 2013
- Microstructure and mechanical properties of Nb–Ti–Si–Al–Hf–xCr–yV multi-element in situ compositeMaterials Science and Engineering: A, 2012
- Study of the role of Al, Cr and Ti additions in the microstructure of Nb–18Si–5Hf base alloysIntermetallics, 2010
- Solid‐Solution Phase Formation Rules for Multi‐component AlloysAdvanced Engineering Materials, 2008
- Study of the role of Al and Cr additions in the microstructure of Nb–Ti–Si in situ compositesIntermetallics, 2005