Can the body slope of interference screw affect initial stability of reconstructed anterior cruciate ligament?: An in-vitro investigation
Open Access
- 18 June 2021
- journal article
- research article
- Published by Springer Nature in BMC Musculoskeletal Disorders
- Vol. 22 (1) , 1-10
Abstract
Background: Superior biomechanical performance of tapered interference screws, compared with non-tapered screws, with reference to the anterior cruciate ligament (ACL) reconstruction process, has been reported in the literature. However, the effect of tapered interference screw’s body slope on the initial stability of ACL is poorly understood. Thus, the main goal of this study was to investigate the effect of the interference screw’s body slope on the initial stability of the reconstructed ACL. Methods: Based on the best screw-bone tunnel diameter ratios in non-tapered screws, two different tapered interference screws were designed and fabricated. The diameters of both screws were equal to bone tunnel diameter in one-third of their length from screw tip, then they were gradually increased by 1mm, in the lower slope (LSTIS), and 2 mm, in the higher slope (HSTIS) screws. To simulate the ACL reconstruction, sixteen soft tissue grafts were fixed, using HSTIS and LSTIS, in synthetic bone blocks. Through applying sub-failure cyclic incremental tensile load, graft-bone-screw construct’s stiffness and graft laxity in each cycle, also through applying subsequent step of loading graft to the failure, maximum load to failure, and graft’s mode of failure were determined. Accordingly, the performance of the fabricated interference screws was compared with each other. Results: HSTIS provides a greater graft-bone-screw construct stiffness, and a lower graft laxity, compared to LSTIS. Moreover, transverse rupture of graft fibers for LSTIS, and necking of graft in the HSTIS group were the major types of grafts’ failure. Conclusions: HSTIS better replicates the intact ACL’s behavior, compared to LSTIS, by causing less damage in graft’s fibers; reducing graft laxity; and increasing fixation stability. Nonetheless, finding the optimal slope remains as an unknown and can be the subject of future studies.Keywords
All Related Versions
This publication has 33 references indexed in Scilit:
- Contact pressure on ACL hamstring grafts in the bone tunnel with interference screw fixation — Dynamic adaptation under loadThe Knee, 2012
- Fixation strength of biocomposite wedge interference screw in ACL reconstruction: effect of screw length and tunnel/screw ratio. A controlled laboratory studyBMC Musculoskeletal Disorders, 2010
- The Effect of Interference Screw Diameter on Fixation of Soft‐Tissue Grafts in Anterior Cruciate Ligament ReconstructionArthroscopy, 2010
- Does Graft Construct Lengthening at the Fixations Cause an Increase in Anterior Laxity Following Anterior Cruciate Ligament Reconstruction in vivo?Journal of Biomechanical Engineering, 2010
- Bioabsorbable Versus Metallic Interference Screw Fixation in Anterior Cruciate Ligament Reconstruction: A Meta‐Analysis of Randomized Controlled TrialsArthroscopy, 2010
- Characterization of the structure–function relationship at the ligament-to-bone interfaceProceedings of the National Academy of Sciences, 2008
- Biomechanics of the anterior cruciate ligament and implications for surgical reconstructionStrategies in Trauma and Limb Reconstruction, 2007
- Graft Laceration and Pullout Strength of Soft‐Tissue Anterior Cruciate Ligament Reconstruction: In Vitro Study Comparing Titanium, Poly‐D,L‐Lactide, and Poly‐D,L‐Lactide–Tricalcium Phosphate ScrewsArthroscopy, 2006
- The effect of screw taper on interference fit during load to failure at the soft tissue/bone interfaceThe Knee, 2005
- Components of laxity in interference fit fixation of quadrupled hamstring graftsActa Orthopaedica, 2002