Effect of Active Air-Cooling Configuration During Interlayer Friction Stir Processing on Grain Morphology and Within-Wall Homogeneity in UAMFSP-Fabricated Aluminum 4043 Walls: A Single-Replicate Exploratory Study
Open Access
- 20 July 2026
- journal article
- research article
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (7) , 252
Abstract
The Unified Additive-Deformation Manufacturing Process (UAMFSP) integrates MIG-based Wire Arc Additive Manufacturing (WAAM) with interlayer Friction Stir Processing (FSP) on a single CNC platform, applying severe plastic deformation to each deposited layer. The novelty of this work is the first controlled comparison, to the authors’ knowledge, of the spatial position of forced-air cooling applied concurrently with the FSP traverse in such an integrated platform: cooling was directed at the top bead surface (TC), at the bottom substrate (BC), or at both surfaces simultaneously (DC), with a MIG-only wall serving as the baseline. Single-layer, four-bead ER4043 aluminum walls were deposited on AA6061 substrates, and optical micrographs from three within-bead locations per condition were quantified with ImageJ, yielding 2038 to 2723 grains per condition. A lumped-parameter thermal model calibrated to infrared thermography ranked the comparative cooling rates as NC < TC < BC < DC. The principal finding is grain homogenization: every FSP condition reduced the grain area scatter by 55 to 71 percent relative to MIG-only, eliminating the coarse-grain tail of the as-deposited distribution regardless of cooling position. Mean equivalent diameters of all four conditions lie within 0.5 µm of one another, at the resolution limit of the optical measurement, so the mean-size ordering (DC finest, 2.76 µm) is reported as a ranking rather than as net refinement. Vickers microhardness on the MIG-only and uncooled FSP walls revealed a 27 HV within-wall gradient (86 ± 7 HV at the stir-zone center versus 59 ± 2 HV at the bead edge), which motivates bilateral cooling for thermal-field homogenization. Because the design is single-replicate, between-condition differences are presented as hypotheses for replicate study with EBSD and spatially resolved hardness mapping.Keywords
This publication has 31 references indexed in Scilit:
- Effect of the active cooling and dwell time to tensile properties of AZ31 wall components by wire-arc directed energy depositionThe International Journal of Advanced Manufacturing Technology, 2026
- Additive manufacturing of hybrid ZrO2–SiC aluminum nanocomposites via a novel WAAM–FSP hybrid methodJournal of Materials Research and Technology, 2026
- Submerged friction stir processing of wire arc additively manufactured Al alloy: Microstructure and mechanical propertiesJournal of Alloys and Compounds, 2024
- An integrated hybrid wire-arc directed energy deposition, friction stir processing, and milling system for multi-track, multi-layer part manufacturingAdditive Manufacturing Letters, 2024
- Microstructure evolution and grain refinement in 2319 aluminium alloy via wire arc additive manufacturing coupled with multi-pass friction stir processingJournal of Alloys and Compounds, 2024
- Improvement of microstructure and fatigue performance of wire-arc additive manufactured 4043 aluminum alloy assisted by interlayer friction stir processingJournal of Materials Science & Technology, 2022
- Oxidation in wire arc additive manufacturing of aluminium alloysAdditive Manufacturing, 2021
- Microstructures and mechanical properties of Al–Zn–Mg aluminium alloy samples produced by wire + arc additive manufacturingJournal of Materials Research and Technology, 2020
- A review of the wire arc additive manufacturing of metals: properties, defects and quality improvementJournal of Manufacturing Processes, 2018
- Submerged friction stir processing of AZ31 Magnesium alloyMaterials & Design (1980-2015), 2013