Sustainable Waterborne Polyurethane Coatings Reinforced with Bio-Functionalized Carbon Nanofillers for Enhanced Protective Performance
- 24 August 2026
- journal article
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 4 (9) , 4970-4985
Abstract
Increasing environmental constraints have intensified the need for coating systems that integrate functional performance with sustainable material design principles. Here, we address this challenge by transitioning from conventional solvent-based polyurethane (PU) to a waterborne system derived from renewable castor oil, a low-cost vegetable resource, while preserving practical performance. To further improve functionality, multi-walled carbon nanotubes (MWCNTs) were added as reinforcing fillers (0.05−0.25 wt %), and their dispersion into the aqueous polymer matrix was enhanced through mild surface modification using tannic acid (a bio-based polyphenol). The resulting hybrid waterborne dispersions remained stable during one month of storage, with dispersions up to 0.1 wt % of MNT-TA maintaining particle sizes <150 nm without detectable aggregation, indicating good colloidal stability. However, the highest filler loading (0.25 wt %) showed slight aggregation, indicating the practical dispersion limit at elevated nanofiller concentrations. This approach enabled the development of an inorganic−organic hybrid coating suitable for direct-to-metal (DTM) applications, offering a strong balance of mechanical strength as well as surface durability. The coatings also exhibited improved wear resistance, withstanding up to 1000 friction cycles, along with a robust adhesive strength of ∼2.4 MPa. Notably, the optimized formulation with a 0.1 wt % filler showed superior electrochemical performance, including a low corrosion current (Icorr: 1.8 × 10−10 A cm−2), reduced corrosion rate (CR: 2.1 × 10−6 mmpy), and high coating resistance (Rp: 4.9 × 106 Ω). Beyond the optimum filler loading, the anticorrosive performance gradually declined as a result of MNT-TA agglomeration. This study presents a unified design strategy based on castor oil-derived polymer synthesis and bio-inspired nanofiller functionalization, resulting in a hybrid coating system that simultaneously achieves sustainability, structural integrity, and enhanced interfacial performance.Keywords
Funding Information
- Council of Scientific and Industrial Research, India (31/0014(19495)/2024-EMR-1)
- Department of Chemicals and Petrochemicals, Ministry of Chemicals and Fertilizers, India (25012/01/2020-PC-II - GAP 0875)
This publication has 51 references indexed in Scilit:
- Interfacial engineering of polyaniline/graphene oxide nanosheets with vermiculites for enhancing anticorrosion performance of epoxy coatingsCarbon, 2025
- Role of Ordered Mesoporous Silica Loaded with Cerium and with an Amine‐Modified Surface as an Effective Binder and Nano‐container in Corrosion Resistant Hybrid CoatingChemistrySelect, 2023
- Stretchable and electrically conductive polyurethane- silver/graphene composite fibers prepared by wet-spinning processComposites Part B: Engineering, 2019
- A computer simulation of stress transfer in carbon nanotube/polymer nanocompositesComposites Part B: Engineering, 2019
- Preparation and characterization of bio‐based polyurethanes obtained from castor oil and poly (3‐hydroxybutyrate) and their nanocompositesPolymer Composites, 2017
- Enhanced thermal conductivity and mechanical properties of polyurethane composites with the introduction of thermally annealed carbon nanotubesMacromolecular Research, 2017
- Synthesis of CNT‐polyurethane nanocomposites using ester‐based polyols with different molecular structure: Mechanical, thermal, and electrical propertiesJournal of Applied Polymer Science, 2016
- Microstructure changes of polyurethane by inclusion of chemically modified carbon nanotubes at low filler contentsComposites Science and Technology, 2012
- Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate–polymer compositesComposites Part B: Engineering, 2008
- Carbon nanotube-reinforced epoxy-composites: enhanced stiffness and fracture toughness at low nanotube contentComposites Science and Technology, 2004