Biomechanical Analysis of 3D Printed and Thermoformed EVA Custom‐Made Mouthguard: Experimental and Finite Element Analyses
Authors:
- Airin Karelys Avendaño RondonARAirin Karelys Avendaño Rondon
- Izabela Batista CordeiroICIzabela Batista Cordeiro
- Maribí Isomar Terán LozadaMLMaribí Isomar Terán Lozada
- Gustavo MendonçaGMGustavo Mendonça
- Priscilla Barbosa Ferreira SoaresPSPriscilla Barbosa Ferreira Soares
- Paulo Sergio BorellaPBPaulo Sergio Borella
- Carlos José SoaresCSCarlos José Soares
Open Access
- 18 December 2025
- journal article
- Published by Wiley in Dental Traumatology
- Vol. 42 (4) , 511-522
Abstract
Background/Objective: 3D printed materials have been evaluated for fabricating mouthguards; however, little is known about their biomechanical performance in preventing dental trauma. This study aimed to compare two 3D printed polymers and three ethylene vinyl acetate (EVA) sheets used for mouthguard fabrication regarding their mechanical properties and stress–strain behavior during impact, analyzed through finite element analysis (FEA). Materials and Methods: Two 3D printed polymers, KeyGuard (Keystone) and DimaPrint (Kulzer), and three EVA sheets, Bio‐art, Essence Dental, and Proform, were used to create the specimens following ISO 37‐II ( n = 10). Shore A hardness was measured on the surface. The breaking force ( F , N), elongation (EL, %), ultimate tensile strength (UTS, MPa), and elastic modulus (E, MPa) were measured using a universal testing machine (EMIC). Density ( ρ , g/cm 3 ) was determined using the test method following ASTM D792. Poisson's ratio was calculated by using axial tensile tests following ASTM D638. Scanning electron microscopy was used to examine the surfaces of EVAs and 3D printed polymers. A two‐dimensional finite element model of the maxillary structure and upper incisor was evaluated with and without a 4.0 mm mouthguard made from each material. An impact simulation was performed by striking the upper incisor with a rigid surface at 1 m/s (3.6 km/h). Strain and modified von Mises stress distributions were evaluated, and mouthguard displacement relative to the tooth was calculated. Results: One‐way ANOVA revealed significant differences among the tested mouthguards for all evaluated parameters ( p < 0.01). Essence Dental showed the highest and DimaPrint the lowest values of F and UTS values ( p < 0.01). Proform was the highest, and DimaPrint had the lowest EL values ( p < 0.01). DimaPrint and KeyGuard had the highest, and Proform had the lowest E values ( p < 0.01). KeyGuard, Essence Dental, and Bio‐art had higher Shore A values than Proform and DimaPrint ( p < 0.01). The 3D printed polymer group had significantly higher Poisson's ratio values than EVAs. The density values were similar for all tested materials ( p = 0.055). The absence of a mouthguard led to greater stress and strain on the impacted tooth. All mouthguards significantly reduced these values, showing comparable shock‐absorbing capacity. Displacement was generally lower in the buccal region and increased toward the palatal side. Conclusion: Although the 3D‐printed polymers exhibited mechanical properties different from EVA materials, all mouthguards demonstrated similar effectiveness for reducing stress and strain on the impacted tooth, indicating comparable protection against dental trauma.Keywords
Funding Information
- Conselho Nacional de Desenvolvimento Científico e Tecnológico (INCT 406840/2022‐9)
- Conselho Nacional de Desenvolvimento Científico e Tecnológico (422603/2021‐0)
- Fundação de Amparo à Pesquisa do Estado de Minas Gerais (APQ‐04262‐2)
- Fundação de Amparo à Pesquisa do Estado de Minas Gerais (RED‐00204‐23)
- Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
This publication has 46 references indexed in Scilit:
- The production and materials of mouthguards: Conventional vs additive manufacturing - A systematic reviewHeliyon, 2024
- Effects of post-curing duration on the mechanical properties of complex 3D printed geometrical partsJournal of the Mechanical Behavior of Biomedical Materials, 2024
- Prevalence and pattern of traumatic orofacial injuries in Kabaddi players in Delhi-NCR regionInjury, 2023
- Mechanical properties of 3D printed mouthguards: Influence of layer height and device thicknessMaterials & Design, 2021
- Child participation in collision sports and football: what influences parental decisions?The Physician and Sportsmedicine, 2021
- A review of the fatigue behavior of 3D printed polymersAdditive Manufacturing, 2019
- Effect of mouthguards on impact to the craniomandibular complexDental Traumatology, 2016
- The effect of antagonist tooth contact on the biomechanical response of custom‐fitted mouthguardsDental Traumatology, 2016
- Custom‐Fitted EVA Mouthguards: what is the ideal thickness? a dynamic finite element impact studyDental Traumatology, 2015
- Evaluation of a dentoalveolar model for testing mouthguards: stress and strain analysesDental Traumatology, 2015