Color Stability, Surface Gloss, Surface Roughness, and Wettability of Material Jetting 3D-Printed Denture Material Under Various Surface Treatments
Open Access
- 20 May 2025
- journal article
- research article
- Published by MDPI AG in Dentistry Journal
- Vol. 13 (5) , 220
Abstract
Objectives: To examine the effects of surface treatments on the color stability, surface roughness, surface gloss, and wettability of monolithic polychromatic material jetting (MJT) 3D-printed denture material. Material and Methods: Twenty-one color variants of the same denture material (TrueDent; Stratasys, Eden, MN, USA) underwent two surface treatments (polishing only or polishing and glazing), creating 42 study groups with a total of 420 samples (n = 10 per group). The samples were manufactured using a PolyJet 3D printer (J5 DentaJet; Stratasys, Eden, MN, USA), a type of MJT 3D printer. Color measurements were taken with a digital spectrophotometer before and after the surface treatments, and quantitative color differences (ΔE00 and ΔC*) were calculated using the CIE2000 system. Comparisons of ΔE00 were made against the 50%:50% acceptability threshold (AT) of 1.8 and the 50%:50% perceptibility threshold (PT) of 0.8 for tooth shade, as well as the 50%:50% PT of 1.72 and the 50%:50% AT of 4.08 for gingival (pink) shade. After surface treatment, the gloss was measured using a glossmeter, surface roughness was measured with optical profilometry, and wettability was measured by contact angle measurements using an optical tensiometer. The significance of surface treatment on color changes for each color variant was evaluated using one-sided, one-sample t-tests against the AT and PT. The effects of surface treatment on surface gloss, surface roughness, contact angle, and ΔC* were analyzed using t-tests for each color variant. Pairwise comparisons between groups were made using Fisher’s Protected Least Significant Differences (α = 0.05). Results: In most cases, glazing caused the color change (ΔE00) to exceed the AT and PT, with a few exceptions. Most materials exhibited a more vibrant (more saturated) appearance and statistically higher chroma, with glazed surface treatments compared to polished ones, though there were some exceptions. For all materials, the glazed samples had significantly higher gloss units than the polished ones (p < 0.0001). Additionally, all materials showed significantly higher surface roughness in glazed samples compared to polished ones (p < 0.0001 for most). The polished samples had significantly higher contact angles (p < 0.0001 for most). Conclusions: Surface treatments significantly influenced the color, surface gloss, surface roughness, and wettability of MJT 3D-printed denture materials. Glazing led to increased chroma and gloss and produced more hydrophilic surfaces, although it also increased surface roughness. These results highlight the importance of surface treatment selection in optimizing the clinical performance of MJT-fabricated dentures.Keywords
This publication has 55 references indexed in Scilit:
- Visually acceptable gloss threshold for resin composite and polishing systemsThe Journal of the American Dental Association, 2021
- Evaluation of surface roughness, hardness and elastic modulus of nanoparticle containing light-polymerized denture glaze materialsJournal of the Mechanical Behavior of Biomedical Materials, 2020
- Effect of biomaterials hydrophobicity and roughness on biofilm developmentJournal of Materials Science: Materials in Medicine, 2019
- Comparison of the CIELab and CIEDE2000 color difference formulasThe Journal of Prosthetic Dentistry, 2016
- Determining color difference thresholds in denture base acrylic resinThe Journal of Prosthetic Dentistry, 2015
- Color and gloss evaluation of titanium dioxide coating for acrylic resin denture baseJournal of Prosthodontic Research, 2015
- Perceptibility and acceptability thresholds for colour differences in dentistryJournal of Dentistry, 2014
- The effect of Parylene coating on the surface roughness of PMMA after brushingJournal of Dentistry, 2013
- SEM and microleakage evaluation of the marginal integrity of two types of class V restorations with or without the use of a light-curable coating material and of polishingJournal of Dentistry, 2008
- A review of tooth colour and whitenessJournal of Dentistry, 2008