A Study on the Optimization of Anisotropic Conductive Films for Sn-3Ag-0.5Cu-Based Flex-on-Board Application at a 250 °C Bonding Temperature
- 30 January 2018
- journal article
- research article
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 8 (3) , 383-391
Abstract
Although cationic epoxy was optimized for low-melting SnBi58 solder ACF joints with the lowest coefficient of thermal expansion (CTE) in terms of reliability, cationic epoxy also showed a faster curing property than any other types of adhesives. In fact, solder joint shapes at 250 °C bonding are very different from those shapes at 200 °C bonding. In this paper, four adhesive film types were investigated in terms of Sn-3Ag-0.5Cu solder ACF joint shapes on the electrical performances and reliability in a pressure cooker test (PCT). Thermal stability of adhesive films was tested to be first. Resin curing speeds were measured in a 250 °C isothermal mode differential scanning calorimetry, resin viscosities were checked by a parallel-plate rheometer, and adhesive thermomechanical properties, such as modulus and CTE, were characterized. Then, four different types of ACF resins containing the same weight percentages of Sn-3Ag-0.5Cu solders were assembled by the same thermocompression bonding parameter (250 °C 10s 2MPa on bump) on a 500-μm-pitch flex-on-board (FOB) application, and different solder joint morphologies were verified. Various bonded solder ACFs joints were compared in terms of solder wetting areas, electrical performances by a four-point-probe method, and the reliability of PCT (121 °C 100% humidity 2atm) for 120 h. This paper aims at optimizing the best adhesive film candidate for SAC305 solder ACF joints of FOB application.Keywords
Funding Information
- National Natural Science Foundation of China (51474081, 61702317)
This publication has 18 references indexed in Scilit:
- A Study on the Bonding Conditions and Nonconductive Filler Contents on Cationic Epoxy-Based Sn–58Bi Solder ACFs Joints for Reliable Flex-on-Board ApplicationsIEEE Transactions on Components, Packaging and Manufacturing Technology, 2017
- Effects of acrylic adhesives property and optimized bonding parameters on Sn 58Bi solder joint morphology for flex-on-board assemblyMicroelectronics Reliability, 2017
- Joint Morphologies and Failure Mechanisms of Anisotropic Conductive Films (ACFs) During a Power Handling Capability Test for Flex-On-Board ApplicationsIEEE Transactions on Components, Packaging and Manufacturing Technology, 2016
- A Study on the Failure Mechanism and Enhanced Reliability of Sn58Bi Solder Anisotropic Conductive Film Joints in a Pressure Cooker Test Due to Polymer Viscoelastic Properties and HydroswellingIEEE Transactions on Components, Packaging and Manufacturing Technology, 2016
- A Study on the Solder Ball Size and Content Effects of Solder ACFs for Flex-on-Board Assembly Applications Using Ultrasonic BondingIEEE Transactions on Components, Packaging and Manufacturing Technology, 2014
- Cu6Sn5 precipitation during Sn-based solder/Cu joint solidification and its effects on the growth of interfacial intermetallic compoundsJournal of Alloys and Compounds, 2014
- Flux function added solder anisotropic conductive films (ACFs) for high power and fine pitch assemblies2013
- Six cases of reliability study of Pb-free solder joints in electronic packaging technologyMaterials Science and Engineering: R: Reports, 2002
- A reliable and environmentally friendly packaging technology-flip-chip joining using anisotropically conductive adhesiveIEEE Transactions on Components and Packaging Technologies, 1999
- Cationic polymerization of diglycidly ether of bisphenol a resins initiated by benzylsulfonium saltsPolymer Composites, 1997