Development of Composite Aluminosilicate Materials Based on Iron–Carbon Fly Ash from CHPP-2: A Comparative Analysis of the Effect of Saryozek and Alekseevskaya Clay Structural Types on Phase Formation During Semi-Dry Pressing
Authors:
- Gulnaz AdilbayevaGAGulnaz Adilbayeva
- Sestager AknazarovSASestager Aknazarov
- Olga GolovchenkoOGOlga Golovchenko
- Aigul AbishevaAAAigul Abisheva
- Zhanibek AmirZAZhanibek Amir
- Makhmud BiisenbayevMBMakhmud Biisenbayev
- Ainur MuratovaAMAinur Muratova
- Assem Zh. AskarovaAAAssem Zh. Askarova
- Aitugan SabitovAitugan Sabitov
Open Access
Abstract
This study presents a comparative analysis of the effect of the structural–mineralogical type of clay matrices on the phase and structure formation in composite aluminosilicate materials within the multi-component Fe-Al-C-Si system. Highly plastic Saryozek montmorillonite clay and moderately plastic Alekseevskaya kaolinite–illite clay were investigated as binding matrices to consolidate iron–aluminosilicate fly ash from the Almaty CHPP-2. The raw materials and binary batches containing 10 to 50 wt.% fly ash were evaluated using XRD, XRF, TG/DTA, and SEM techniques. The results demonstrate that the superior plastic and binding properties of the Saryozek clay ensure enhanced consolidation of the non-plastic, fragmented ash particles. Simultaneous thermal analysis reveals that increasing the compaction pressure from 20 to 30 MPa induces a kinetic shift in the montmorillonite dehydroxylation interval toward higher temperatures (580–720 °C) due to increased partial water vapor pressure within the dense green body. This thermal shift scientifically necessitates introducing an isothermal dwell at 600 °C to mitigate firing defects. The optimal composite properties are achieved at a molding pressure of 30 MPa, a firing temperature of 1050 °C, and a fly ash concentration of 10–20 wt.%, yielding a peak compressive strength of 38.4 MPa. SEM confirmed that under these conditions, the locally formed silicate melt uniformly encapsulates the crystalline mullite and quartz microparticles, whereas increasing the ash content to 50 wt.% results in a loose, highly porous structure that degrades strength down to 17.9 MPa. These findings lay a scientifically substantiated foundation for optimizing composite ceramic synthesis and reducing structural defects.Keywords
All Related Versions
This publication has 28 references indexed in Scilit:
- Physicochemical analysis and speed-induced stress modelling of sugarcane bagasse ash-stabilized scarified pavement for subgrade applicationMultiscale and Multidisciplinary Modeling, Experiments and Design, 2026
- Fly ash as a sustainable reinforcement in composite materials: a comprehensive review on enhancing mechanical properties for eco-friendly engineeringDiscover Materials, 2025
- Study of Flash-Based Concrete with Nano-SiO₂ Particles by Destructive TestProcedia Structural Integrity, 2025
- A review on the effect of fly ash on the geotechnical properties and stability of soilCleaner Materials, 2022
- Morphology and chemical composition of mineral matter present in fly ashes of bituminous coal and ligniteInternational Journal of Environmental Science and Technology, 2020
- Current Challenges and Opportunities in Microstructure-Related Properties of Advanced High-Strength SteelsMetallurgical and Materials Transactions A, 2020
- Fly-ash cenosphere/clay blended composites for impact resistant tilesConstruction and Building Materials, 2017
- Strategies for Tailoring the Pore-Size Distribution of Virus Retention Filter PapersACS Applied Materials & Interfaces, 2016
- Thermal and structural properties of Ca-rich Montmorillonite mechanically deformed by compaction and shearApplied Clay Science, 2006
- The microstructural study of thermal treatment montmorillonite from Heping, ChinaSpectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, 2005