Aigul Abisheva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Aigul Abisheva has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Ainur Muratova
Alfa-Standard Center for Expertise and Certification, Seifullin Avenue 531, Almaty 050000, Kazakhstan
2 shared publications - Aitugan Sabitov
Department of Analytical, Colloid Chemistry and Technology of Rare Elements, Al-Farabi Kazakh National University, Al-Farabi Ave., 71, Almaty 050040, Kazakhstan
2 shared publications - Assem Zh. Askarova
Alfa-Standard Center for Expertise and Certification, Seifullin Avenue 531, Almaty 050000, Kazakhstan
2 shared publications - Gulnaz Adilbayeva
Department of Chemical Physics and Materials Science, Al-Farabi Kazakh National University, Al-Farabi Avenue 71, Almaty 050040, Kazakhstan
2 shared publications - Makhmud Biisenbayev
Scientific and Technical Center “Zhalyn”, Pavlodarskaya street 11, Almaty 050050, Kazakhstan
2 shared publications - Olga Golovchenko
Department of Chemical Physics and Materials Science, Al-Farabi Kazakh National University, Al-Farabi Avenue 71, Almaty 050040, Kazakhstan
2 shared publications
Latest Publications
- Open Access
Development of Composite Aluminosilicate Materials Based on Iron–Carbon Fly Ash from CHPP-2: A Comparative Analysis of the Effect of Saryozek and Alekseevskaya Clay Structural Types on Phase Formation During Semi-Dry Pressing
This study presents a comparative analysis of the effect of the structural–mineralogical type of clay matrices on the phase and structure formation in composite aluminosilicate materials within the multi-component Fe-Al-C-Si system. Highly plastic Saryozek montmorillonite clay and moderately plastic Alekseevskaya kaolinite–illite clay were investigated as binding matrices to consolidate iron–aluminosilicate fly ash from the Almaty CHPP-2. The raw materials and binary batches containing 10 to 50 wt.% fly ash were evaluated using XRD, XRF, TG/DTA, and SEM techniques. The results demonstrate that the superior plastic and binding properties of the Saryozek clay ensure enhanced consolidation of the non-plastic, fragmented ash particles. Simultaneous thermal analysis reveals that increasing the compaction pressure from 20 to 30 MPa induces a kinetic shift in the montmorillonite dehydroxylation interval toward higher temperatures (580–720 °C) due to increased partial water vapor pressure within the dense green body. This thermal shift scientifically necessitates introducing an isothermal dwell at 600 °C to mitigate firing defects. The optimal composite properties are achieved at a molding pressure of 30 MPa, a firing temperature of 1050 °C, and a fly ash concentration of 10–20 wt.%, yielding a peak compressive strength of 38.4 MPa. SEM confirmed that under these conditions, the locally formed silicate melt uniformly encapsulates the crystalline mullite and quartz microparticles, whereas increasing the ash content to 50 wt.% results in a loose, highly porous structure that degrades strength down to 17.9 MPa. These findings lay a scientifically substantiated foundation for optimizing composite ceramic synthesis and reducing structural defects.
Open AccessDevelopment of Composite Aluminosilicate Materials Based on Iron–Carbon Fly Ash from CHPP-2: A Comparative Analysis of the Effect of Saryozek and Alekseevskaya Clay Structural Types on Phase Formation During Semi-Dry Pressing
This study presents a comparative analysis of the effect of the structural–mineralogical type of clay matrices on the phase and structure formation in composite aluminosilicate materials within the multi-component Fe-Al-C-Si system. Highly plastic Saryozek montmorillonite clay and moderately plastic Alekseevskaya kaolinite–illite clay were investigated as binding matrices to consolidate iron–aluminosilicate fly ash from the Almaty CHPP-2. The raw materials and binary batches containing 10 to 50 wt.% fly ash were evaluated using XRD, XRF, TG/DTA, and SEM techniques. The results demonstrate that the superior plastic and binding properties of the Saryozek clay ensure enhanced consolidation of the non-plastic, fragmented ash particles. Simultaneous thermal analysis reveals that increasing the compaction pressure from 20 to 30 MPa induces a kinetic shift in the montmorillonite dehydroxylation interval toward higher temperatures (580–720 °C) due to increased partial water vapor pressure within the dense green body. This thermal shift scientifically necessitates introducing an isothermal dwell at 600 °C to mitigate firing defects. The optimal composite properties are achieved at a molding pressure of 30 MPa, a firing temperature of 1050 °C, and a fly ash concentration of 10–20 wt.%, yielding a peak compressive strength of 38.4 MPa. SEM confirmed that under these conditions, the locally formed silicate melt uniformly encapsulates the crystalline mullite and quartz microparticles, whereas increasing the ash content to 50 wt.% results in a loose, highly porous structure that degrades strength down to 17.9 MPa. These findings lay a scientifically substantiated foundation for optimizing composite ceramic synthesis and reducing structural defects.
- Open Access
- 21 July 2026
- Published by MDPI AG in Preprints.org
Development of Composite Aluminosilicate Materials Based on Iron-Carbon Fly Ash from CHPP-2: A Comparative Analysis of the Effect of Saryozek and Alekseevskaya Clay Structural Types on Phase Formation During Semi-Dry Pressing
This study presents a comparative analysis of the effect of the structural-mineralogical type of clay matrices on the phase and structure formation in composite aluminosilicate materials within the multi-component Fe-Al-C-Si system. Highly plastic Saryozek montmorillonite clay and moderately plastic Alekseevskaya kaolinite-illite clay were investigated as binding matrices to consolidate iron-aluminosilicate fly ash from the Almaty CHPP-2. The raw materials and binary batches containing 10 to 50 wt.% fly ash were evaluated using XRD, XRF, TG/DTA, and SEM techniques. The results demonstrate that the superior plastic and binding properties of the Saryozek clay ensure enhanced consolidation of the non-plastic, fragmented ash particles. Simultaneous thermal analysis reveals that increasing the compaction pressure from 20 to 30 MPa induces a kinetic shift in the montmorillonite dehydroxylation interval toward higher temperatures (580 °C –720 °C) due to increased partial water vapor pressure within the dense green body. This thermal shift scientifically necessitates introducing an isothermal dwell at 600°C to mitigate firing defects. The optimal composite properties are achieved at a molding pressure of 30 MPa, a firing temperature of 1050 °C, and a fly ash concentration of 10–20 wt.%, yielding a peak compressive strength of 38.4 MPa. SEM analysis confirmed that under these conditions, the locally formed silicate melt uniformly encapsulates the crystalline mullite and quartz microparticles, whereas increasing the ash content to 50 wt.% results in a loose, highly porous structure that degrades strength down to 17.9 MPa. These findings lay a scientifically substantiated foundation for optimizing composite ceramic synthesis and reducing structural defects.
- 21 July 2026
- Published by MDPI AG in Preprints.org
Open AccessDevelopment of Composite Aluminosilicate Materials Based on Iron-Carbon Fly Ash from CHPP-2: A Comparative Analysis of the Effect of Saryozek and Alekseevskaya Clay Structural Types on Phase Formation During Semi-Dry Pressing
This study presents a comparative analysis of the effect of the structural-mineralogical type of clay matrices on the phase and structure formation in composite aluminosilicate materials within the multi-component Fe-Al-C-Si system. Highly plastic Saryozek montmorillonite clay and moderately plastic Alekseevskaya kaolinite-illite clay were investigated as binding matrices to consolidate iron-aluminosilicate fly ash from the Almaty CHPP-2. The raw materials and binary batches containing 10 to 50 wt.% fly ash were evaluated using XRD, XRF, TG/DTA, and SEM techniques. The results demonstrate that the superior plastic and binding properties of the Saryozek clay ensure enhanced consolidation of the non-plastic, fragmented ash particles. Simultaneous thermal analysis reveals that increasing the compaction pressure from 20 to 30 MPa induces a kinetic shift in the montmorillonite dehydroxylation interval toward higher temperatures (580 °C –720 °C) due to increased partial water vapor pressure within the dense green body. This thermal shift scientifically necessitates introducing an isothermal dwell at 600°C to mitigate firing defects. The optimal composite properties are achieved at a molding pressure of 30 MPa, a firing temperature of 1050 °C, and a fly ash concentration of 10–20 wt.%, yielding a peak compressive strength of 38.4 MPa. SEM analysis confirmed that under these conditions, the locally formed silicate melt uniformly encapsulates the crystalline mullite and quartz microparticles, whereas increasing the ash content to 50 wt.% results in a loose, highly porous structure that degrades strength down to 17.9 MPa. These findings lay a scientifically substantiated foundation for optimizing composite ceramic synthesis and reducing structural defects.
- Open Access
- 11 July 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (7) , 267
High-Temperature Synthesis of Superconducting MgB2 Materials in a Centrifuge
There is a wide variety of superconducting materials, but only a few of them are suitable for practical industrial use, and one of the most promising superconductors is MgB2. Its main advantages are a critical temperature close to 40 K, which allows for operation in a cryogenic environment, low cost of precursors, and the ease of manufacture. In this paper, we attempted to obtain superconducting materials based on magnesium diboride in a new way by using a high-temperature centrifuge and then investigated how centrifugal acceleration could affect the superconducting characteristics of the materials in a greater way during combustion synthesis. As a brief result of this research, it was found that the value of centrifugal acceleration affected the critical current density (Jc = 1.4 A/cm2) of the MgB2 composites, although it did not considerably impact the critical transition temperature of the MgB2 materials (remained at around 37.5–38 K).
- 11 July 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (7) , 267
Open AccessHigh-Temperature Synthesis of Superconducting MgB2 Materials in a Centrifuge
There is a wide variety of superconducting materials, but only a few of them are suitable for practical industrial use, and one of the most promising superconductors is MgB2. Its main advantages are a critical temperature close to 40 K, which allows for operation in a cryogenic environment, low cost of precursors, and the ease of manufacture. In this paper, we attempted to obtain superconducting materials based on magnesium diboride in a new way by using a high-temperature centrifuge and then investigated how centrifugal acceleration could affect the superconducting characteristics of the materials in a greater way during combustion synthesis. As a brief result of this research, it was found that the value of centrifugal acceleration affected the critical current density (Jc = 1.4 A/cm2) of the MgB2 composites, although it did not considerably impact the critical transition temperature of the MgB2 materials (remained at around 37.5–38 K).