In Vitro Analysis of Biodegradation Properties and Sterilization Stability of PLA Membranes for Bone Regeneration
Open Access
- 2 October 2025
- journal article
- research article
- Published by Springer Nature in Journal of Maxillofacial and Oral Surgery
- p. 1-14
Abstract
Introduction: Modern maxillofacial surgery increasingly emphasizes the restoration and regeneration of oral tissues, particularly the hard tissues of the jaws. Bone defects may arise from disease, trauma, or congenital anomalies. Guided bone regeneration (GBR) using barrier membranes is a widely accepted technique for managing such defects. However, standard titanium and PTFE membranes require a secondary surgical procedure for removal, limiting their clinical convenience. Although resorbable collagen membranes avoid this issue, they often lack sufficient structural integrity, making them less effective for vertical or complex bone augmentation. Aim: This study aimed to evaluate the physicochemical properties of biodegradable membranes based on polylactic acid (PLA), its copolymers, and composite materials for potential use in GBR. In addition, the effects of sterilizing doses of ionizing radiation were assessed to determine an optimal sterilization protocol. Materials and Methods: The materials tested included pure PLA, PLA reinforced with hydroxyapatite (PLA/HAP), and polyglycolic acid (PLGA) in two compositions: 85:15 and 60:40. Physicochemical properties and responses to electron beam sterilization (25 kGy) were analyzed. Biodegradation was evaluated in phosphate-buffered saline at 37 °C. Sample morphology and molecular structure were assessed using infrared (IR) spectroscopy and scanning electron microscopy (SEM). Results: After one month, PLGA (60:40) samples exhibited approximately 40% mass loss, while PLGA (85:15) showed only about 5%. Pure PLA remained largely intact, with less than 1% mass loss. Non-irradiated PLA/HAP samples degraded inconsistently, with mass loss ranging from negligible to 19%, while irradiated PLA/HAP samples exhibited minimal degradation (up to 2%). This increased stability may be due to radiation-induced crystallinity, though further investigation is needed. In some cases, a slight mass increase was observed, possibly due to water diffusion into deeper composite layers. Among all tested materials, pure PLA demonstrated the highest stability, retaining its shape and showing minimal degradation throughout the study period. Conclusion: The results support the potential use of PLA and its copolymers for developing biodegradable membranes in GBR. Ionizing radiation appears to be a viable sterilization method, with minimal impact on material integrity. Further optimization of physicochemical properties and degradation behavior is warranted to facilitate clinical application in maxillofacial surgery.Keywords
Funding Information
- Loma Linda University
This publication has 25 references indexed in Scilit:
- Ginsenoside Rg5 nanomedicine composited hydrogel with metabolic regulation and immunomodulation properties for tunneling diabetic wounds therapyChemical Engineering Journal, 2023
- Bio-based polyether from limonene oxide catalytic ROP as green polymeric plasticizer for PLAPolymer, 2020
- Effects of gamma irradiation on 3D-printed polylactic acid (PLA) and high-density polyethylene (HDPE)Polymer Bulletin, 2020
- Preparation and characterization of PLA/PCL/HA composite scaffolds using indirect 3D printing for bone tissue engineeringMaterials Science and Engineering: C, 2019
- Current Progress in Tendon and Ligament Tissue EngineeringTissue Engineering and Regenerative Medicine, 2019
- Polyglycolic acid‐collagen tube combined with collagen‐binding basic fibroblast growth factor accelerates gait recovery in a rat sciatic nerve critical‐size defect modelJournal of Biomedical Materials Research Part B: Applied Biomaterials, 2019
- Investigation of anti-corrosive properties of poly(aniline-co-2-pyridylamine-co-2,3-xylidine) and its nanocomposite poly(aniline-co-2-pyridylamine-co-2,3-xylidine)/ZnO on mild steel in 0.1 M HClApplied Surface Science, 2016
- The modification of PLA and PLGA using electron‐beam radiationJournal of Biomedical Materials Research Part A, 2008
- The complete process of bioresorption and bone replacement using devices made of forged composites of raw hydroxyapatite particles/poly l-lactide (F-u-HA/PLLA)Biomaterials, 2005
- An Overview of Polylactides as Packaging MaterialsMacromolecular Bioscience, 2004