A. P. Reutova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
A. P. Reutova has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Andrey I. Yaremenko
First Pavlov University, Ministry of Health of Russia
2 shared publications - Maria A. Markova
Radiation Technology Department, St. Petersburg State Institute of Technology, Technical University, 190013 St. Petersburg, Russia
2 shared publications - Zhanna B. Lyutova
Radiation Technology Department, St. Petersburg State Institute of Technology, Technical University, 190013 St. Petersburg, Russia
2 shared publications - A.V. Popugaev
Petersburg Nuclear Physics Institute named by B.P. Konstantinov of National Research Centre “Kurchatov Institute
1 shared publication E.A. Zernitskaya
Clinic ”Hollywood smile
1 shared publication- Ekaterina A. Zernitckaia
Department of Implant Dentistry Loma Linda University School of Dentistry Loma Linda California USA
1 shared publication
Latest Publications
- 26 February 2026
- Published by Media Sphere Publishing Group in Stomatologiya
- Vol. 105 (1) , 21-30
Experimental study of radiation sterilization and degradation of polylactide and copolymer membranes for maxillofacial surgery
Objective. The aim of the study. To evaluate the physicochemical properties and radiation stability of biodegradable membranes based on polylactic acid (PLA) and its copolymers (PLGA) for potential use in guided bone regeneration (GBR) in maxillofacial surgery. Materials and methods. Membranes made of pure PLA, PLA with hydroxyapatite (PLA/HAP), and polylactic-co-glycolic acid (PLGA) in 85:15 and 60:40 ratios were studied. Samples were sterilized using electron beam irradiation at a dose of 25 kGy. Degradation was carried out in phosphate-buffered saline at 37 °C. Molecular structure was assessed by FTIR spectroscopy, and surface morphology was evaluated using scanning electron microscopy (SEM). Results. After one month, PLGA 60:40 samples lost approximately 40% of their mass and structural integrity and were excluded from further observation. PLGA 85:15 samples maintained shape and exhibited a minor mass loss (~5%). Non-irradiated PLA/HAP composites showed variable mass loss (0—19%), while irradiated ones displayed minimal changes (up to 2%). Pure PLA samples remained the most stable throughout the 2.5-month observation period, showing only minor hydrolytic surface alterations. Radiation sterilization did not cause significant changes in the molecular structure of any tested materials. Conclusion. PLA copolymers demonstrated controlled degradation rates and sufficient structural stability, making them promising candidates for the development of patient-specific resorbable membranes for GBR. Their predictable resorption profile may eliminate the need for secondary surgery to remove the membrane. The results support the feasibility of using ionizing radiation for sterilization without compromising material properties.
- 26 February 2026
- Published by Media Sphere Publishing Group in Stomatologiya
- Vol. 105 (1) , 21-30
Experimental study of radiation sterilization and degradation of polylactide and copolymer membranes for maxillofacial surgery
Objective. The aim of the study. To evaluate the physicochemical properties and radiation stability of biodegradable membranes based on polylactic acid (PLA) and its copolymers (PLGA) for potential use in guided bone regeneration (GBR) in maxillofacial surgery. Materials and methods. Membranes made of pure PLA, PLA with hydroxyapatite (PLA/HAP), and polylactic-co-glycolic acid (PLGA) in 85:15 and 60:40 ratios were studied. Samples were sterilized using electron beam irradiation at a dose of 25 kGy. Degradation was carried out in phosphate-buffered saline at 37 °C. Molecular structure was assessed by FTIR spectroscopy, and surface morphology was evaluated using scanning electron microscopy (SEM). Results. After one month, PLGA 60:40 samples lost approximately 40% of their mass and structural integrity and were excluded from further observation. PLGA 85:15 samples maintained shape and exhibited a minor mass loss (~5%). Non-irradiated PLA/HAP composites showed variable mass loss (0—19%), while irradiated ones displayed minimal changes (up to 2%). Pure PLA samples remained the most stable throughout the 2.5-month observation period, showing only minor hydrolytic surface alterations. Radiation sterilization did not cause significant changes in the molecular structure of any tested materials. Conclusion. PLA copolymers demonstrated controlled degradation rates and sufficient structural stability, making them promising candidates for the development of patient-specific resorbable membranes for GBR. Their predictable resorption profile may eliminate the need for secondary surgery to remove the membrane. The results support the feasibility of using ionizing radiation for sterilization without compromising material properties.
- Open Access
- 2 October 2025
- Published by Springer Nature in Journal of Maxillofacial and Oral Surgery
- p. 1-14
In Vitro Analysis of Biodegradation Properties and Sterilization Stability of PLA Membranes for Bone Regeneration
Introduction: Modern maxillofacial surgery increasingly emphasizes the restoration and regeneration of oral tissues, particularly the hard tissues of the jaws. Bone defects may arise from disease, trauma, or congenital anomalies. Guided bone regeneration (GBR) using barrier membranes is a widely accepted technique for managing such defects. However, standard titanium and PTFE membranes require a secondary surgical procedure for removal, limiting their clinical convenience. Although resorbable collagen membranes avoid this issue, they often lack sufficient structural integrity, making them less effective for vertical or complex bone augmentation. Aim: This study aimed to evaluate the physicochemical properties of biodegradable membranes based on polylactic acid (PLA), its copolymers, and composite materials for potential use in GBR. In addition, the effects of sterilizing doses of ionizing radiation were assessed to determine an optimal sterilization protocol. Materials and Methods: The materials tested included pure PLA, PLA reinforced with hydroxyapatite (PLA/HAP), and polyglycolic acid (PLGA) in two compositions: 85:15 and 60:40. Physicochemical properties and responses to electron beam sterilization (25 kGy) were analyzed. Biodegradation was evaluated in phosphate-buffered saline at 37 °C. Sample morphology and molecular structure were assessed using infrared (IR) spectroscopy and scanning electron microscopy (SEM). Results: After one month, PLGA (60:40) samples exhibited approximately 40% mass loss, while PLGA (85:15) showed only about 5%. Pure PLA remained largely intact, with less than 1% mass loss. Non-irradiated PLA/HAP samples degraded inconsistently, with mass loss ranging from negligible to 19%, while irradiated PLA/HAP samples exhibited minimal degradation (up to 2%). This increased stability may be due to radiation-induced crystallinity, though further investigation is needed. In some cases, a slight mass increase was observed, possibly due to water diffusion into deeper composite layers. Among all tested materials, pure PLA demonstrated the highest stability, retaining its shape and showing minimal degradation throughout the study period. Conclusion: The results support the potential use of PLA and its copolymers for developing biodegradable membranes in GBR. Ionizing radiation appears to be a viable sterilization method, with minimal impact on material integrity. Further optimization of physicochemical properties and degradation behavior is warranted to facilitate clinical application in maxillofacial surgery.
- 2 October 2025
- Published by Springer Nature in Journal of Maxillofacial and Oral Surgery
- p. 1-14
Open AccessIn Vitro Analysis of Biodegradation Properties and Sterilization Stability of PLA Membranes for Bone Regeneration
Introduction: Modern maxillofacial surgery increasingly emphasizes the restoration and regeneration of oral tissues, particularly the hard tissues of the jaws. Bone defects may arise from disease, trauma, or congenital anomalies. Guided bone regeneration (GBR) using barrier membranes is a widely accepted technique for managing such defects. However, standard titanium and PTFE membranes require a secondary surgical procedure for removal, limiting their clinical convenience. Although resorbable collagen membranes avoid this issue, they often lack sufficient structural integrity, making them less effective for vertical or complex bone augmentation. Aim: This study aimed to evaluate the physicochemical properties of biodegradable membranes based on polylactic acid (PLA), its copolymers, and composite materials for potential use in GBR. In addition, the effects of sterilizing doses of ionizing radiation were assessed to determine an optimal sterilization protocol. Materials and Methods: The materials tested included pure PLA, PLA reinforced with hydroxyapatite (PLA/HAP), and polyglycolic acid (PLGA) in two compositions: 85:15 and 60:40. Physicochemical properties and responses to electron beam sterilization (25 kGy) were analyzed. Biodegradation was evaluated in phosphate-buffered saline at 37 °C. Sample morphology and molecular structure were assessed using infrared (IR) spectroscopy and scanning electron microscopy (SEM). Results: After one month, PLGA (60:40) samples exhibited approximately 40% mass loss, while PLGA (85:15) showed only about 5%. Pure PLA remained largely intact, with less than 1% mass loss. Non-irradiated PLA/HAP samples degraded inconsistently, with mass loss ranging from negligible to 19%, while irradiated PLA/HAP samples exhibited minimal degradation (up to 2%). This increased stability may be due to radiation-induced crystallinity, though further investigation is needed. In some cases, a slight mass increase was observed, possibly due to water diffusion into deeper composite layers. Among all tested materials, pure PLA demonstrated the highest stability, retaining its shape and showing minimal degradation throughout the study period. Conclusion: The results support the potential use of PLA and its copolymers for developing biodegradable membranes in GBR. Ionizing radiation appears to be a viable sterilization method, with minimal impact on material integrity. Further optimization of physicochemical properties and degradation behavior is warranted to facilitate clinical application in maxillofacial surgery.